Ronix RH-4980 Pallet Truck Instruction Manual
- July 17, 2024
- Ronix
Table of Contents
Ronix RH-4980 Pallet Truck Instruction Manual
TECHNICAL SPECIFICATION
PART LIST
WARNING!
The use of the pallet truck, maintenance and repair must be done in accordance
with the requirements of the manufacturers.
Prohibits any modification or installed on attachments, to ensure that the
pallet truck is safe.
RANGE OF APPLICATION
– Pallet truck have steady lifting, manipulation of portable, safe and
reliable, etc.
– Ground: rough, hard, level and no holes and obstacles.
SETUP AND ASSEMBLY
– Insert the base of the handle into the pump bracket.
– Align the holes at the base of the handle with the holes in the pump
bracket.
– Using a screwdriver, pry the cam up and slip the cam net under the notch in
the cam.
– Insert handle pins into the holes of the pump bracket and handle. Align the
spring pin holes in the handle pin and the pump bracket.
– Tap the handle pins into place with a hammer.
– Using a hammer, tap the spring pins into the pump bracket and handle pins.
OPERATIONS
– To raise forks, place handle in the UP position.
– To lower forks, pull lever handle to DOWN position (upper part of slot).
– To freely move the handle, set lever in Neutral (center notch of slot).
– The cam nut is properly adjusted when pumping the handle in NEUTRAL position
causes no movement of the hydraulic ram.
INTRODUCTION
To better understand the proper use and safe operation of this pallet truck, please take a few minutes to carefully read and follow the instructions contained in this manual. When finished reading and understanding the manual, please file in a safe and convenient location for the life of the pallet truck. If the pallet trucktransfers ownership, the manual should accompany it.
This pallet truck is designed to push and pull palletized material loads up to
3000 kilogram only.
You will notice several important features about your WDFE Pallet Truck. For
example, the heavygauge steel frame is reinforced with cross welded steel
plates to prevent forks from bending and solid steel push rods are used for
added strength.
The pump features top of the stroke and overload by-pass valve systems. A
durable powder coat finish provides long lasting steel protection. Extra wide
polyurethane covered steel steer wheels and nylon load wheels feature lifetime
lubricated, double sealed bearings to provide smooth, quiet rolling and added
stability.
SAFETY WARNINGS
– Read and understand the entire owner‘s manual before attempting assembly or
operation of the pallet truck.
– Read and understand the warnings on the pallet truck and in this manual.
Failure to comply with all of these warnings may cause serious injury.
– Replace the warning labels if they become obscured or removed.
– Do not use this pallet truck for other than its intended use. If used for
other purposes, factory, disclaims any real or implied warranty and holds
itself harmless from any injury that may result from that use.
– Do not place hands or feet under the pallet truck at any time.
– Do not operate a loaded pallet truck on ramps orinclines.
– Do not tip load pallet truck forks. This may cause damage to the forks and
personal injury if the rear of the pallet truck suddenly pops up.
– Never leave a loaded pallet truck unattended in the raised position. Always
lower load to the floor.
– Do not load pallet truck beyond its rated capacity of 3000 Kilogram. Secure
load before transporting.
– To prevent accidental tipping, make sure load is centered on the forks.
– Do not move a loaded pallet truck by other than manual force.
CLEANING RELEASE VALVE
– Over time, the hydraulic pump assembly may become clogged with debris or air bubbles, and not function properly.
TO CLEAN THE RELEASE VALVE AND BLEED THE PUMP:
– Pump handle quickly, raising pallet truck to full extent. While continuing
pumping action, pull lever to down position.
– When forks reach total down position, valve is flushed. Repeat if necessary.
LUBRICATION
Check oil level annually by removing oil plug foundon top of pump housing. When changing or addingoil, fill the tank through the oil plug screw hole to 80% capacity with hydraulic jack oil, about 2” deep in pump ousing. Do not use any other type of oil.
TROUBLESHOOTING THE WDFE SERIES PALLET TRUCKS
WASTE DISPOSAL
Abandoned hydraulic oil can‘t literally throw, must pay attention to environmental protection, should be dealt with in accordance with local laws and regulations.
Documents / Resources
|
Ronix RH-4980 Pallet
Truck
[pdf] Instruction Manual
RH-4980, RH-4980 Pallet Truck, Pallet Truck, Truck
---|---