Dynojet Power Commander 6 Suzuki TL1000R 1998-2003 Installation Guide
- October 27, 2023
- Dynojet
Table of Contents
POWER COMMANDER 6
Installation Guide for: PC6-20055
Model Coverage: 1998-2003 Suzuki TL1000R
IPC6-20055.01
PARTS LIST
1 POWER COMMANDER 6
1 INSTALLATION GUIDE
1 USB CABLE
2 DYNOJET DECALS
2 POWER COMMANDER DECALS
2 VELCRO STRIPS
1 ALCOHOL SWAB
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION. THE IGNITION MUST BE TURNED OFF BEFORE INSTALLATION.
INPUT ACCESSORY GUIDE
OPTIONAL ACCESSORY INPUTS
Map
(Input 1 or 2) The PC6 has the ability to hold 2 different base maps. You
can switch on the fl y between these two base maps when you hook up a switch to
the MAP inputs. You can use any open/close type switch. The polarity of the
wires is not important.
Shifter
(Input 1 or 2) Used for clutch-less full throttle upshifts. Insert the
wires from the Dynojet quick shifter into either Input 1 or Input 2. The
polarity of the wires is not important. Set to Input 2 by default.
Speed
If your application has a speed sensor then you can tap into the signal
side of the sensor and run a wire into this input. This will allow you to
calculate gear position in the Control Center Software. Once gear position is
setup you can alter your map based on gear position and setup gear dependent
kill times when using a quick shifter.
Analog
This input is for a 0-5v signal such as engine temp, boost, etc. Once this
input is established you can alter your fuel curve based on this input in the
Power Core software.
Launch
You can connect a wire to either Input 1 or Input 2 and then the other end
to a switch. This switch when engaged (continuity) will only allow the RPM to
be raised to a certain limit (set in the software). When released, you will
have full RPM.
WIRE CONNECTIONS
To input wires into the PC6 fi rst remove the rubber plug on the backside of
the unit and loosen the screw for the corresponding input. Using a 22-24 gauge
wire, strip about 10mm from its end. Push the wire into the hole of the PC6
until it stops and then tighten the screw. Make sure to reinstall the rubber
plug.
NOTE: If you tin the wires with solder it will make inserting them
easier.
INSTALLING THE POWER COMMANDER 6
-
Remove the main seat and the passenger seat or solo cover.
-
Prop the fuel tank up using the prop rod in the tail section.
-
Lay the PC6 in the tail section.
-
Route the wiring harness from the PC6 under the tail section and go towards the battery.
-
Route the PC6 harness under the fuel tank bracket and to the left side of the rear cylinder.
-
Locate and unplug the stock 6-pin clear connectors. These connectors can be found to the left rear of the air box.
-
Plug the connectors from the PC6 in-line of the stock wiring harness and the throttle body sub-harness.
-
Locate and unplug the Throttle Position Sensor. This TPS connector has RED, GREY, and BLACK/BROWN wires and is located on the left hand side of the throttle body.
-
Plug the connectors from the PC6 in-line of the stock wiring harness and the TPS.
-
Remove the battery access panel from the left hand fairing.
-
Remove the battery cover.
-
Route the ground wire from the PC6 down the left side of the engine to the battery.
-
Attach the ground wire from the PC6 to the negative side of the battery.
-
Install the PC6 in the tail section using the supplied Velcro. Make sure to clean both surfaces with the alcohol swab before attaching the Velcro.
-
Replace all body work and lower the fuel tank back into position making sure none of the wires get pinched or damaged.
Download the latest map files from our web site at dynojet.com/tunes.
PUSH THE LIMIT
2191 MENDENHALL DRIVE, NORTH LAS VEGAS, NV 89081 – 800-992-4993 –
DYNOJET.COM
© 1998-2022 DYNOJET RESEARCH ALL RIGHTS RESERVED
PC6-20055
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>