wilo PB 088 EA Pressure Booster Pump Instruction Manual

**wilo PB 088 EA Pressure Booster Pump Instruction Manual

**

About this document

The language of the original operating instructions is English. All other languages of these instructions are translations of the original operating instructions.
These installation and operating instructions are an integral part of the product. They must be kept readily available at the place where the product is installed. Strict adherence to these instructions is a precondition for the proper use and correct operation of the product.
These installation and operating instructions correspond to the relevant version of the product and the underlying safety standards valid at the time of going to print.

EC declaration of conformity:
A copy of the EC declaration of conformity is a component of these operating instructions.
If a technical modification is made on the designs named there without our agreement, this declaration loses its validity.

Safety

These operating instructions contain basic information which must be adhered to during installation, operation and maintenance. For this reason, these operating instructions must, without fail, be read by the service technician and the responsible specialist/ operator before installation and commissioning.
It is not only the general safety instructions listed under the main point “safety” that must be adhered to but also the special safety instructions with danger symbols included under the following main points.

General danger symbol
Danger due to electrical voltage
Note

Personnel qualifications

The installation, operating, and maintenance personnel must have the appropriate qualifications for this work. Area of responsibility, terms of reference and monitoring of the personnel are to be ensured by the operator. If the personnel are not in possession of the necessary knowledge, they are to be trained and instructed. This can be accomplished if necessary by the manufacturer of the product at the request of the operator.

Danger in the event of non-observance of the safety instructions

Non-observance of the safety instructions can result in risk of injury to persons and damage to the environment and the product/unit. Non observance of the safety instructions results in the loss of any claims to damages.
In detail, non-observance can, for example, result in the following risks:

• Danger to persons from electrical, mechanical and bacteriological influences,
• Damage to the environment due to leakage of hazardous materials.
• Property damage
• Failure of important product/unit functions
• Failure of required maintenance and repair procedures

Safety consciousness on the job

The safety instructions included in these installation and operating instructions, the existing national regulations for accident prevention together with any internal working, operating and safety regulations of the operator are to be complied with.

Safety instructions for the operator

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• If hot or cold components on the product/the unit lead to hazards, local measures must be taken to guard them against touching.
• Guards protecting against touching moving components (such as the coupling) must not be removed whilst the product is in operation.
• Leakages (e.g. from the shaft seals) of hazardous fluids (which are explosive, toxic or hot) must be led away so that no danger to persons or to the environment arises. National statutory provisions are to be complied with.
• Highly flammable materials are always to be kept at a safe distance from the product.
• Danger from electrical current must be eliminated.
  Local directives or general directives [e.g. IEC, VDE etc.] and local power supply companies must be adhered to.

Safety instructions for installation and maintenance work

The operator must ensure that all installation and maintenance work is carried out by authorised and qualified personnel, who are sufficiently informed from their own detailed study of the operating instructions.
Work on the product/unit must only be carried out when at a standstill. It is mandatory that the procedure described in the installation and operating instructions for shutting down the product/unit be complied with. Immediately on conclusion of the work, all safety and protective devices must be put back in position and/or recommissioned.

Unauthorised modification and manufacture of spare parts

Unauthorised modification and manufacture of spare parts will impair the safety of the product/ personnel and will make void the manufacturer’s declarations regarding safety.
Modifications to the product are only permissible after consultation with the manufacturer. Original spare parts and accessories authorised by the manufacturer ensure safety. The use of other parts will absolve us of liability for consequential events.

Improper use

The operating safety of the supplied product is only guaranteed for conventional use in accordance with Section 4 of the operating instructions. The limit values must on no account fall under or exceed those specified in the catalogue/data sheet.

Transport and interim storage

When you receive the equipment, check that it has not been damaged during transport. If you notice a fault, take all necessary action with the carrier within the time allowed.

CAUTION! Storage environment may cause damage.
If the equipment is to be installed at a later date, store it in a dry place and protect it from impacts and any external stresses (humidity, frost etc.).
Temperature range for transport and storage: -30°C to +60°C Handle the pump with care so as not to damage the product before installation.

Application

These devices are domestic pressure boosting systems designed for pressurising clean water.
The downward type is designed for boosting water from roof-top water tank to lower floors using water and the upward type is designed for boosting water from the tank on the ground to upper floors.

DANGER! Risk of explosion!
Do not use this pump to convey flammable or explosive liquids.

Technical data

Data table

Upward type (60 Hz)

only)
DN of suction connection| 1″| 1 1/Ł”
DN of pressure connection
Temperature range
Fluid temperature range| +5°C to +60°C
Ambient temperature| max. +Ł0°C
Electrical data
Motor protection rating| IPXŁ
Insulation class| F_155
Frequency| 60 Hz 220 V
Voltage
Other
Max. sound level| 62 dB(A)

Upward type (50 Hz)

only)
DN of suction connection| 1″| 1 1/Ł”
DN of pressure connection
Temperature range
Fluid temperature range| +5°C to +60°C
Ambient temperature| max. +Ł0°C
Electrical data
Motor protection rating| IPXŁ
Insulation class| F_155
Frequency| 50 Hz 220 V – 230 V
Voltage
Other
Max. sound level| 62 dB(A)

Downward type (60 Hz)

Hydraulic data| PB-138MA| PB-S250MA| PB-350/351MA| PB- 600MA
---|---|---|---|---
Maximum operating pressure| 1.8 bar (1.8 x 105 Pa)| 2.3 bar (2.3 x 105 Pa)| 3.2 bar (3.2 x 105 Pa)| Ł.2 bar (Ł.2 x 105 Pa)
Maximum suction pressure| 0.6 bar (0.6 x 105 Pa)| 0.8 bar (0.8 x 105 Pa)| 1.1 bar (1.1 x 105 Pa)| 1.Ł bar (1.Ł x 105 Pa)
Maximum altitude| 1000 m
Suction head| –
DN of suction connection| 3/Ł”| 1 1/Ł“
DN of pressure connection
Temperature range
Fluid temperature range| +5°C to +80°C
Ambient temperature| max. +Ł0°C
Electrical data
Motor protection rating| IPXŁ
Insulation class| F_155
Frequency| 50 Hz 220 V – 230 V
Voltage
Other
Max. sound level| 62 dB(A)

Downward type (50 Hz)

Hydraulic data| PB-088EA| PB-S125EA| PB-201EA| PB- 400EA
---|---|---|---|---
Maximum operating pressure| 1.2 bar (1.2 x 105 Pa)| 1.6 bar (1.6 x 105 Pa)| 2.2 bar (2.2 x 105 Pa)| 3 bar (3 x 105 Pa)
Maximum suction pressure| 0.Ł bar (0.Ł x 105 Pa)| 0.5 bar (0.5 x 105 Pa)| 0.7 bar (0.7 x 105 Pa)| 1 bar (1 x 105 Pa)
Maximum altitude| 1000 m
Suction head| –
DN of suction connection| 3/Ł”| 1 1/Ł“
DN of pressure connection
Temperature range
Fluid temperature range| +5°C to +80°C
Ambient temperature| max. +Ł0°C
Electrical data
Motor protection rating| IPXŁ
Insulation class| F_155
Frequency| 50 Hz 220 V – 230 V
Voltage
Other
Max. sound level| 62 dB(A)

Scope of delivery

• Single-stage horizontal automatic pump
• Installation and operating instructions
• Assembly package (2 sets of unions, nipples, gaskets for piping, for PB-088EA, PB-138MA, PB-350MA only)
• Assembly package (2 sets of flanges, gaskets, for upward type only)

Products and functions

Product description (see Figures)

Pressure boosting system for domestic applications which require higher water pressure from a roof-top water tank (downward type) or a water tank on the ground (upward type).

Product function

Operating option as “Auto”, “Manual”, “Off” for downward type only.
Automatic operation with flow switch.
Automatic operation with flow switch and pressure switch in case of upward type.

The pump

Single-stage horizontal centrifugal, non self-priming pump.
Shaft sealing with mechanical seal.

The motor

Single-phase, 2-pole, 50 Hz and 60 Hz motor, capacitor in the terminal box, thermal protector for motor protection.

• Protection class: IPX4
• Insulation class: F_155

2Ł0V( +6%)

Installation and connections

All installation and electrical connection work must be carried out solely by authorised and qualified personnel, in accordance with applicable regulations.

WARNING! Physical injuries!
The applicable regulations for the prevention of accidents must be complied with.

Upon receipt of the product

• Unpack the pump and recycle or dispose of the packaging in an environmentally responsible manner.

Hydraulic connections

General connection instructions

• Use flexible, braid-reinforced hose piping or rigid piping.
• The pump must not bear the weight of the pipes.
• Seal the piping well using appropriate products.

Suction connections

• The diameter of the suction pipe must never be less than the port on the product.

Handling and installation

• See Fig. 1 to 4 for upward type.
  
  
  
  

• See Fig. 5 to 11 for downward type.
  
  
  

(Fig. 8 installation is available only PB-200EA and PB-350MA)

• Suction mode installation of upward type (Fig. 2). Fig. 2, item 1: Foot valve (not in the scope of delivery)

Electrical connection

WARNING! Risk of electric shock!
Danger from electrical current must be eliminated.

• Have all electrical work carried out by a qualified electrician only!
• Before any electrical connection is made, the pump must be de energised (switched off) and protected against unauthorised restarting.
• To ensure safe installation and operation, the unit must be earthed correctly with the earth terminals of the power supply.

CAUTION! An error in the electrical connection will damage the motor.
The power cable must never touch the piping or the pump, and must be kept away from any moisture.

• See the pump cladding for its electrical characteristics (frequency, voltage, current).
• The single-phase motor of this pump has a builtin thermal protector.
• See the wiring diagram marked on inside of terminal cover, fasten the cable with cable gland and cable anchorage located in terminal box securely when the cable connect.
• The cross-section of supply cord for this pump shall be at least 3 x 0,75 mm² and properties of supply cord shall be at lease ordinary polychloroprene sheathed cords (60245 IEC 57).
• A damaged cable or connector must be replaced by the corresponding part available from the manufacturer or the manufacturer’s customer service.

Commissioning

Check that there are no leaks at the connections to the sanitary devices connected to the lifting unit.

• Switch on the power supply to the unit.
• Check that the current consumed is less than or equal to the rated current.

Maintenance

All maintenance work must be carried out by authorised and qualified personnel!

WARNING! Risk of electric shock!
Danger from electrical current must be eliminated.

Before carrying out any electrical work, the pump must be de-energised (switched off) and protected against unauthorised restarting.
It is recommended to disconnect the plug.

• No special maintenance work required during operation.
• Keep the pump clean.
• If the pump is deactivated for a long period and there is no risk of freezing, it is best not to drain the pump.
  In the event of prolonged absence, be sure to cut off the mains water supply and protect the installation from freezing.

Faults, causes and remedies

not operate. Then, wait until the motor is cold. (20 – 30 minutes)
Faulty cable connection| Insert the power plug securely
Cable is disconnected or damaged.| Replace the cable
Trouble in the motor| Repair or replace the motor
Power supply voltage is too low.| Check the voltage of the power supply and consult with the local power supplier
Water is not pumped out even though the motor is running| Water level of well is lower than standard level| Check the water level of well
Fault in foot valve| Take off the check valve case and then clean the valve, valve seat and valve hole
Air is drawn into suction hose| Check for leaks in the entire pipe and seal these if any are found
Air is drawn into pump from mechanical seal| Replace the mechanical seal
Thermal protector for motor works too often| Power supply voltage is either too low or too high| Check the voltage of the power supply and consult with the local power supplier
Impeller is in contact with another component| Repair the defects.
Short or open circuit of the capacitor| Repair or replace the capacitor.
Water does not come during the first few minutes after being switched on| Air is drawn into suction pipe| Check for leaks in the entire pipe or replace the defective piping (to prevent air leaking)
Pump starts without water| Piping or pump are leaking water| Repair piping, pump parts and faucets, etc
Water leaks on mechanical seal| Replace the mechanical seal
Trouble in check valve| Take off the check valve case and then, clean the valve, valve seat and valve hole
Defacement or transformation of the impeller| Replace the impeller

If you cannot remedy the fault, please contact Wilo customer service.

Spare parts

All spare parts should be ordered directly from Wilo customer service.
To prevent errors, always quote the data on the pump’s rating plate when making an order.
The spare parts catalogue is available at: www.wilo.com.

Disposal

Your device contains valuable raw materials which can be recycled. Therefore, please take your device to your local collection point in your town or district.

Subjet to technical modifications

EU/EC DECLARATION OF CONFORMITY

We, manufacturer, declare under our sole responsability that the pump types of the series

PB-…EA
PB-S…EA
PB-…SEA

The serial number is marked on the product site plat

In their delivered state comply with the following relevant directives:

• Low voltage 2014/35/EU from April 20th 2016
• Electromagnetic compatibility 2014/30/EU from April 20th 2016
• Restriction of the use of certain hazardous substances 2011/65/EU and with the relevant national legislation, comply also with the following relevant harmonized European standards :

EN 60335-2-41

EN 61000-3-2:2014
EN 61000-3-3:2013

EN 55014-1:2006+A1+A2:2011
EN 55014-2:2015

Dortmund,

H. HERCHENHEIN
Senior Vice President – Group ITQ

Digital
unterschrieben von
Holger Herchenhein
Datum: 2017.01.06
09:24:54 +01’00’

N°2156052.01 (CE-A-S n°3077642)

WILO SE
Nortkirchenstraβe 100
44263 Dortmund – Germany

Wilo – International (Subsidiaries)

Argentina
WILO SALMSON
Argentina S.A.
C1295ABI Ciudad
Autónoma de Buenos Aires
T +54 11 4361 5929
carlos.musich@wilo.com.ar

Australia
WILO Australia Pty Limited
Murrarrie, Queensland, 4172
T +61 7 3907 6900
chris.dayton@wilo.com.au

Austria
WILO Pumpen Österreich
GmbH
2351 Wiener Neudorf
T +43 507 507-0
office@wilo.at

Azerbaijan
WILO Caspian LLC
1065 Baku
T +994 12 5962372
info@wilo.az

Belarus
WILO Bel IOOO
220035 Minsk
T +375 17 3963446
wilo@wilo.by

Belgium
WILO NV/SA
1083 Ganshoren
T +32 2 4823333
info@wilo.be

Bulgaria
WILO Bulgaria EOOD
1125 Sofia
T +359 2 9701970
info@wilo.bg

Brazil
WILO Comercio e
Importacao Ltda
Jundiaí – São Paulo – Brasil
13.213-105
T +55 11 2923 9456
wilo@wilo-brasil.com.br

Canada
WILO Canada Inc.
Calgary, Alberta T2A 5L7
Bay 8, 925 – 30th Street NE.
T +1 403 276 9456
info@wilo-canada.com

China
WILO China Ltd.
101300 Beijing
T +86 10 58041888
wilobj@wilo.com.cn

Croatia
WILO Hrvatska d.o.o.
10430 Samobor
T +38 51 3430914
wilo-hrvatska@wilo.hr

Cuba
WILO SE
Officina Comercial
Edificio Simona Apto 105
Siboney. La Habana. Cuba
T +53 5 2795135
T +53 7 272 2330
raul.rodriguez@wilo-cuba.com

Czech Republic
WILO CS, s.r.o.
25101 Cestlice
T +420 234 098711
info@wilo.cz

Denmark
WILO Danmark A/S
2690 Karlslunde
T +45 70 253312
wilo@wilo.dk

Estonia
WILO Eesti OÜ
12618 Tallinn
T +372 6 509780
info@wilo.ee

Finland
WILO Finland OY
02330 Espoo
T +358 207401540
wilo@wilo.fi

France
Wilo Salmson France S.A.S.
53005 Laval Cedex
T +33 2435 95400
info@wilo.fr

Great Britain
WILO (U.K.) Ltd.
Burton Upon Trent
DE14 2WJ
T +44 1283 523000
sales@wilo.co.uk

Greece
WILO Hellas SA
4569 Anixi (Attika)
T +302 10 6248300
wilo.info@wilo.gr

Hungary
WILO Magyarország Kft
2045 Törökbálint
(Budapest)
T +36 23 889500
wilo@wilo.hu

India
Wilo Mather and Platt Pumps
Private Limited
Pune 411019
T +91 20 27442100
services@matherplatt.com

Indonesia
PT. WILO Pumps Indonesia
Jakarta Timur, 13950
T +62 21 7247676
citrawilo@cbn.net.id

Ireland
WILO Ireland
Limerick
T +353 61 227566
sales@wilo.ie

Italy
WILO Italia s.r.l.
Via Novegro, 1/A20090
Segrate MI
T +39 25538351
wilo.italia@wilo.it

Kazakhstan
WILO Central Asia
050002 Almaty
T +7 727 312 40 10
info@wilo.kz

Korea
WILO Pumps Ltd.
20 Gangseo, Busan
T +82 51 950 8000
wilo@wilo.co.kr

Latvia
WILO Baltic SIA
1019 Riga
T +371 6714-5229
info@wilo.lv

Lebanon
WILO LEBANON SARL
Jdeideh 1202 2030
Lebanon
T +961 1 888910
info@wilo.com.lb

Lithuania
WILO Lietuva UAB
03202 Vilnius
T +370 5 2136495
mail@wilo.lt

Morocco
WILO Maroc SARL
20250 Casablanca
T +212 (0) 5 22 66 09 24
contact@wilo.ma

The Netherlands
WILO Nederland B.V.
1551 NA Westzaan
T +31 88 9456 000
info@wilo.nl

Norway
WILO Norge AS
0975 Oslo
T +47 22 804570
wilo@wilo.no

Poland
WILO Polska Sp. z.o.o.
5-506 Lesznowola
T +48 22 7026161
wilo@wilo.pl

Portugal
Bombas Wilo-Salmson
Sistemas Hidraulicos Lda.
4475-330 Maia
T +351 22 2080350
bombas@wilo.pt

Romania
WILO Romania s.r.l.
077040 Com. Chiajna
Jud. Ilfov
T +40 21 3170164
wilo@wilo.ro

Russia
WILO Rus ooo
123592 Moscow
T +7 495 7810690
wilo@wilo.ru

Saudi Arabia
WILO Middle East KSA
Riyadh 11465
T +966 1 4624430
wshoula@wataniaind.com

Serbia and Montenegro
WILO Beograd d.o.o.
11000 Beograd
T +381 11 2851278
office@wilo.sk

Slovakia
WILO CS s.r.o., org. Zložka
83106 Bratislava
T +421 2 33014511
info@wilo.sk

Slovenia
WILO Adriatic d.o.o.
1000 Ljubljana
T +386 1 5838130
wilo.adriatic@wilo.si

South Africa
Wilo Pumps SA Pty LTD
1685 Midrand
T +27 11 6082780
patrick.hulley@salmson.co.za

Spain
WILO Ibérica S.A.
8806 Alcalá de Henares
(Madrid)
T +34 91 8797100
wilo.iberica@wilo.es

Sweden
WILO NORDIC AB
35033 Växjö
T +46 470 727600
wilo@wilo.se

Switzerland
Wilo Schweiz AG
4310 Rheinfelden
T +41 61 836 80 20
info@wilo.ch

Taiwan
WILO Taiwan CO., Ltd.
24159 New Taipei City
T +886 2 2999 8676
nelson.wu@wilo.com.tw

Turkey
WILO Pompa Sistemleri
San. ve Tic. A.S¸
34956 İstanbul
T +90 216 2509400
wilo@wilo.com.tr

Ukraina
WILO Ukraina t.o.w. 08130
Kiew
T +38 044 3937384
wilo@wilo.ua

United Arab Emirates
WILO Middle East FZE Jebel
Ali Free zone – South PO
Box 262720 Dubai
T +971 4 880 91 77
info@wilo.ae

USA
WILO USA LLC Rosemont,
IL 60018
T +1 888 945 6872
info@wilo-usa.com

Vietnam
WILO Vietnam Co Ltd. Ho
Chi Minh City, Vietnam T
+84 8 38109975
nkminh@wilo.vn

WILO SE
Nortkirchenstraße 100
D-44263 Dortmund
Germany
T +49(0)231 4102-0
F +49(0)231 4102-7363
wilo@wilo.com
www.wilo.com

References

• Canada.Com | Homepage | Canada.Com
• USA Location information - USA.com
• Wilo Corporate - Pioneering for You | WILO

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>