METER ATMOS 41W All-In-One Wireless Weather Station User Guide
- June 9, 2024
- METER
Table of Contents
ATMOS 41W All-In-One Wireless Weather Station
User Guide
ATMOS 41W All-In-One Wireless Weather Station
SUPPORT
Have a question or problem? Our support team can help.
We manufacture, test, calibrate, and repair every instrument in house. Our
scientists and technicians use the instruments every day in our product
testing lab. No matter what your question is, we have someone who can help
you answer it.
NORTH AMERICA
Email:
support.environment@metergroup.com
Phone: +1.509.332.5600
EUROPE
Email: support.europe@metergroup.com
Phone: +49 89 12 66 52 0
Introduction
Prior to field installation, please verify all ATMOS 41W components arrived intact. Please carefully follow Step 1 and Step 2 before taking the device into the field for installation. Read the complete user manual at meterly /atmos41W-support.
Verify Cellular Signal
When evaluating where to install the ATMOS 41W, METER recommends verifying
adequate cellular signal (Step 3C) for the chosen location. The cellular
signal must be strong enough for data to be transmitted to ZENTRA Cloud.
Data Access
ATMOS 41W data are accessed online via ZENTRA Cloud, a web application used
to download, view, and share data as well as to change configurations.
The ATMOS 41W requires a paid subscription to use ZENTRA Cloud. See Step 2 to
learn how to add the ATMOS 41W to ZENTRA Cloud.
Save the orange device subscription card included with the ATMOS 41W in a safe
location. This card contains the following information for the subscription:
- Device serial number
- Password
- Server name where sensor data is stored.
ATTENTION
For best results, use the latest versions of ZENTRA Utility
Mobile software and ATMOS 41W firmware.
ZENTRA Utility Mobile will prompt with available updates for software and
ATMOS 41W fi rmware. Consult the ATMOS 41W User Manual (meter.ly/atmos41W-
support) for more troubleshooting tips.
Field Installation
A. Mount ATMOS 41W
Toward True North Place the top of the post under the mounting shelf.
The ATMOS 41W must be set up with the engraved N on the instrument oriented to
true north (not magnetic north).
B. Mount and Secure Device
Tighten the V-bolt nuts by hand until hand-tight, and then tighten with the
13-mm wrench (included).
CAUTION Do not overtighten the bolt.
C. Level the Device
Use the bubble level underneath the ATMOS 41W.
The weather station angle can be adjusted by loosening the leveling screw
attached to the bottom with the 8-mm wrench (included), moving the weather
station side to side as needed to level, and then retightening the
screw.
D. Reverify Communication and Cellular Signal
Use ZENTRA Utility Mobile to review instantaneous measurements and verify the
sensor is working as expected.
Press Test in ZENTRA Utility
Mobile to check the quality of the cellular signal before finalizing
installation.
The ATMOS 41W is now installed and data should be available after the fi rst
upload.
E. Connect the ATMOS 41W
On the Connect screen in the app.
Select the desired device to connect.
Bluetooth connection will be established and ATMOS 41W and sensor information
will be retrieved.
F . Replace Rain Funnel
Line up the padlocks, press down, and twist rain funnel clockwise until it
locks.
NOTE: Be sure the cable and connector are clear of the internal spring
and are not pinched before closing.
G. Confi gure ATMOS 41W
Select Confi gure.
Review the cellular data upload setting and the sensor measurement interval.
Make changes if desired.
Save changes.
H. Verify Readings
Select Refresh in the app to show a list of readings.
Verify that these readings are within expected ranges.
The ATMOS 41W is now ready for use.
Add ATMOS 41W to ZENTRA Cloud
Prior to fi eld installation, please do the following. ZENTRA Cloud is best viewed on a laptop or tablet:
A. Create User Account
Using a web browser, navigate to the server listed on the orange Device
Subscription card.
Select the Sign Up button.
Enter valid email address and user information.
Accept Terms and Conditions.
B. Verify User Account
Select the Sign Up button (generates email confi rmation).
Click on the hyperlink in the confi rmation email to verify the user account.
C. Create Organization
Log into ZENTRA Cloud.
Select Create Organization.
Enter Organization name.
Enter Role.
Select Accept. 
D. Add Device
Click on Add New button.
Select Device from the menu.
Enter the Device Serial
Number and the Device
Password from the orange
Device Subscription card (remove from funnel and store in safe location).
Click the Create button to subscribe and add device to the organization.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>