DiO 54717 1.0 Wireless Switch User Manual

DiO 54717 1.0 Wireless Switch

WHAT IS IN THE BOX

Video tutorial

We have produced a series of video tutorials to make it easier to understand and install our solutions. You can view them on our Youtube.com/c/dio- connected-home channel, in the Playlists tab. You can also view them through our website www.chacon.com in the Support tab.

Install the wireless switch

Activating the switch
Remove the back plate of the switch (see paragraph 2) and remove the tab on the battery.

Installing the unit

1. Remove the back plate of the switch to place the wall mounting screws.
2. Fix the back plate to the wall using the screws or double-sided stickers provided, making sure that the arrow is pointing upwards .
3. Fix the switch to the back plate by aligning the 6 clips and with a little force push forward until you hear a small “click” (attention: respect the position of the upward arrow).

Changing the battery

When the battery is low, the switch LED will start flashing red once every 4 seconds.
To change the battery :

1. Insert a small flat screwdriver into the slot on the bottom of the switch to remove the switch from the back plate.
2. Remove the old battery with the flat screwdriver and replace with a new 3V CR2032 type battery, making sure to place the + facing up.
3. Reposition the switch on the back plate by aligning the 6 clips and pushing until you hear a “click”.
   Caution: Danger of explosion if the battery is not replaced correctly. Replace only with the same or equivalent type.

Linking the switch with the receiver

1. Connect the receiver (module, socket, bulb).
2. Bring the wireless switch close to the DiO 1.0 receiver and press the receiver learn button (see receiver manual); the receiver LED flashes.
3. Press the ON button of the switch to link them.
4. The LED on the switch flashes green once and the LED on the module/socket flashes twice to confirm the association.

Advanced options: setting a timer

The DiO wireless switch allows you to program a timer, which will automatically switch off your DiO receiver(s) (socket, light module …) after the set time has elapsed. Several timers are possible: no timer, 5s, 1m, 10m, 30m, 60m.

Programming a timer :

1. Press the ON and OFF button simultaneously for 3 seconds, the LED starts flashing green, and release.
2. Press the ON button again to select your timer.
   • 0x ON: no timer, LED flash 1 time
   • 1x ON: 5 sec, LED flash 2 times
   • 2x ON: 1minute, LED flash 3 times
   • 3x ON: 10 minutes, LED flash 4 times
   • 4x ON: 30 minutes, LED flash 5 times
   • 5x ON: 60 min, LED flash 6 times
   • To return to the previous timer, press OFF once.
3. To confirm your timer, press ON and OFF simultaneously for 3 seconds, the LED will flash green rapidly to confirm the programming.

If no action is taken for 16 seconds, the switch will exit the programming mode and no timer will be saved.

Deleting the link between the wireless switch and a DiO

If you want to delete a receiver from the switch:

1. Bring the switch close to the receiver to be deleted and press the receiver learn button (socket, module, doorbell, bulb – see product manual); the receiver LED flashes.
2. Press the ‘OFF’ button of the switch; the LEDs on the switch and on the receiver will flash red twice to confirm the deletion.

Use

ON/OFF control: Press the ON button of the wireless switch once to turn your light, device, roller shutter, etc. on, or the OFF button once to turn it off.
Dimmer (only with a dimmer module, socket or bulb): Press the ON button of the wireless switch twice; the brightness starts to increase/decrease; press ON again to stop the increase/decrease.
When you turn off the light with the OFF button, the last brightness level selected will be retained in the receiver memory.DiO 1.0 receivers (lighting module, shutter module, socket, bulb, etc.) can be controlled individually or in conjunction with other receivers (e.g.: a DiO switch closes the shutter linked to a DiO shutter module and at the same time turns on the lamp connected to the lighting module, and the DiO remote control turns the lamp on and off individually).

Troubleshooting

The receiver is not activated when the remote control is pressed:

• Check the po larity of the battery and/or that it is not flat.
• Make sure that the wireless switch is linked to the receiver and that the receiver is connected correctly.
• Check the status of the receiver memory (see receiver manual).

Important: The range between the receiver and the remote control is 50 m, but this may be reduced by the thickness of the walls or a currently wireless environment.
A minimum distance of 1-2 m is necessary between two DiO receivers (module, socket and/or bulb).
Do not use in a damp location.

Technical specifications

• Protocol: DiO 1.0
• Frequency: 433.92 MHz
• EIRP: < 1W
• Operating temperature: -10 to 35°C
• Transmission range: 50 m (in free field)
• Lithium battery: CR2032 3V (included)
• Number of channels: 1
• Dimensions: 80 x 80 x 15 mm

Indoor use (IP20). Do not use in a damp environment.

Supplementing your installation

Supplement your installation with DiO solutions to control your heating, lighting, roller shutters, or garden, or to use video surveillance to keep an eye on what is happening at home.
Easy, high-quality, scalable and economical…learn about all of the DiO Connected Home solutions at

Recycling
In accordance with European WEEE directives (2002/96/EC) and directives concerning accumulators (2006/66/EC), any electrical or electronic device or accumulator must be collected separately by a local system specialising in the collection of such waste. Do not dispose of these products with ordinary waste. Check the regulations in force. The logo shaped like a waste bin indicates that this product must not be disposed of with household waste in any EU country. To prevent any risk to the environment or human health due to uncontrolled scrapping, recycle the product in a responsible manner. This will promote the sustainable use of material resources. To return your used device, use the return and collection systems, or contact the original dealer. The dealer will recycle it in accordance with regulatory provisions.
CHACON declares that device 54717 conforms with the requirements and provisions of Directive RED
2014/53/EU.
The complete text of the EU declaration of conformity is available at the following Internet address:
www.chacon.com/conformity

Support

www.chacon.com/support

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>