DIO 3-Channel Remote Control 54760 User Manual

DIO 3-Channel Remote Control 54760 User Manual

What’s In The Box

• lx 54760

• lx Manual

• lx CR2032 3V battery

Vide tutorial

We have produced a series of video tutorials to make it easier to understand and install our solutions. You can view them on our Youtube.com/c/dio- connected-home channel, in the Playlists tab. You can also view them through our website www.chacon.com in the Support tab.

Changing the battery in your remote control

1. Insert a 3mm flat head screwdriver into the small slot just above the battery compartment and pull the cover down to open the compartment.
2. Using a small screwdriver, push the battery toward the outside.
3. Replace the old battery with a new 3V CR2032 battery.

Warning: Risk of explosion if the battery is not replaced correctly. Replace only with the same type or an equivalent type.

Linking the remote control with a DiO 1.0 module, socket or bulb

This product is compatible with all DiO 1.0 and DiO Connect peripherals operating under the DiO 433MHz radio protocol, as well as with the DiO home automation control unit, to control it with a smartphone or by voice (via a Google Home or Amazon Alexa smart speaker).

Linking the remote control with the receiver

1. Connect the receiver (module, socket, bulb).
2. Bring the remote control close to the DiO 1.0 receiver and press the receiver learn button (see receiver manual); the receiver LED flashes.
3. Press the ‘I’ button on the remote control to link them. 4. The lamp connected to the module/socket flashes twice to confirm the link and the LED stops flashing.

Deleting the link between the remote control and a DiO receiver

If the remote control memory is full or if you want to delete a receiver:

1. Bring the remote control close to the receiver to be deleted and press the receiver learn button (socket, module, doorbell, bulb — see product manual); the receiver LED flashes.
2. Press the OFF’ (0) button of the remote control to be deleted; the lamp flashes twice to confirm the deletion and the LED of the receiver stops flashing.

Use

Individual control (channel 1, 2, 3):
ON/OFF : Press the ‘I’ button of the remote control once to turn your light, device, roller shutter, etc. on, or the ‘0’ button once to turn it off.
Dimmer (only with a dimmer module, socket or bulb): Press the ‘I’ button of the remote control twice; the brightness starts to increase/decrease; press ‘I’ again to stop the increase/decrease. When you turn off the light with the ‘0’ button, the last brightness level selected will be retained in the receiver memory.

Group function: Press the ‘I’ or ‘0’ button on channel G to turn on/off all the lamps or devices registered on the remote control (on channels 1 to 3).

DiO 1.0 receivers (lighting module, shutter module, socket, bulb, etc.) can be controlled individually or in conjunction with other receivers (e.g.: a DiO switch closes the shutter linked to a DiO shutter module and at the same time turns on the lamp connected to the lighting module, and the DiO remote control turns the lamp on and off individually).

Troubleshooting

The receiver is not activated when the remote control is pressed:

• Check the polarity of the battery and/or that it is not flat.
• Make sure that the remote control is linked to the receiver and that the receiver is connected correctly.
• Check the status of the receiver memory (see receiver manual).

Important: The range between the receiver and the remote control is 50 m, but this may be reduced by the thickness of the walls or a currently wireless environment. A minimum distance of 1-2 m is necessary between two DiO receivers (module, socket and/or bulb).
Do not use in a damp location.

Technical specifications

• Protocol: DiO 1.0
• Frequency: 433.92 MHz
• Transmission range: 50 m (in free field)
• Lithium battery: CR2032 3V (included)
• Number of channels: 3 + 1 group
• Dimensions: 125 x 35 x 11 mm

Indoor use (IP20). Do not use in a damp environment.

Supplementing your installation

Supplement your installation with DiO solutions to control your heating, lighting, roller shutters, or garden, or to use video surveillance to keep an eye on what is happening at home.
Easy, high-quality, scalable and economical…learn about all of the DiO Connected Home solutions at www.chacon.com.

Recycling

 In accordance with European WEEE directives (2002/96/EC) and directives concerning accumulators (2006/66/EC), any electrical or electronic device or accumulator must be collected separately by a local system specialising in the collection of such waste. Do not dispose of these products with ordinary waste. Check the regulations in force. The logo shaped like a waste bin indicates that this product must not be disposed of with household waste in any EU country. To prevent any risk to the environment or human health due to uncontrolled scrapping, recycle the product in a responsible manner. This will promote the sustainable use of material resources. To return your used device, use the return and collection systems, or contact the original dealer. The dealer will recycle it in accordance with regulatory provisions.

 CHACON declares that device 54760 conforms with the requirements and provisions of Directive RED 2014/53/EU. The complete text of the EU declaration of conformity is available at the following Internet address: www.chacon.com/conformity

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>