GLOBAL INDUSTRIAL 641765 1/2HP Axial Air Mover Instruction Manual
- June 6, 2024
- GLOBAL INDUSTRIAL
Table of Contents
GLOBAL INDUSTRIAL 641765 1/2HP Axial Air Mover Instruction Manual
641765
1/2hp Axial Air Mover
READ ENTIRE MANUAL BEFORE
USE Global Industrial-11 Harbor Park Drive Port Washington-NY 11050
Safety Instructions
Please observe the following safety instructions to avoid personal injury and property loss.
- Do not operate any fan with a damaged cord or Plug.
- Do not move or adjust blower while in operation
- Keep this unit out of the reach of children
- Do not alter or modify your blower in any way. Only authorized Global Industrial replacement parts can be used. Use of any unauthorized parts could cause hazards and void the unit’s warranty
- Always store unit in a clean, dry environment when not in use. Care should be taken to prevent water from entering the unit’s motor. In the case that the unit’s motor does become wet, ensure that the motor is dried thoroughly before use.
- Do not allow water near or inside the unit while in use to avoid risk of electric shock. Handle unit with care to avoid causing damage or personal injury.
- Always operate the blower on a flat, level surface. Operating the unit where it could slip or fall increases the risk of injury, fire, or electrical shock.
- Never operate the blower without the factory-installed safety screens in place. This will prevent liquids, gases, and other materials from entering the blower.
- Do not use blower near combustible gas or flammable materials in order to avoid fire or electrical hazards.
- Do not attempt to disassemble or repair unit on your own. Instead, bring to the attention of your distributor or a certified repair center. Never attempt to disassemble or repair unit while blower is plugged in.
- Prior to use, ensure the air intake and outlet are free of obstructions to prevent the blower from overheating.
Operating Procedures
The Global Industrial line of commercial ventilator is designed to efficiently and effectively ventilate, extract and circulate air. Be sure to follow all instructions below to ensure safe and effective use.
- Ensure that the unit is on a stable, level surface, and remains stationary while in use.
- Plug the blower into a grounded outlet with the correct voltage and amperage. Ensure that the unit is plugged into a grounded outlet with voltage and wattage outputs that correspond with the unit’s specifications. For maximum protection against electrical shock, ALWAYS use a circuit that is protected by a ground fault circuit interrupter. If you are unsure about the outlet, check with a qualified electrician.
- Ensure that the dial is turned to your desired speed setting before turning the unit on.
GFCI Power Outlet
This blower is equipped with a built-in GFCI outlet that allows you to “daisy chain” multiple units together in order to operate in large areas where power outlets are limited in number or unavailable. All other warnings for use of this blower should be strictly adhered to. Total Max 12amps can be connected when the Unit is OFF.
Resettable Circuit Breaker
The thermal response resettable circuit breaker protects the unit and connected daisy chained devices. The circuit breaker is designed to sense the total current drawn through the circuit. When more than 12 amps of electrical current are drawn through the unit’s power cord, the circuit breaker trips. To reset, unplug the appliance causing the breaker to trip and push the Reset Button adjacent to the outlets on the Fan.
Controls
The blower Fan equip the 2 speed switch.
Control fan with the switch
II- Turn on the fan with high speed
0- Turn off the fan
1- Turn on the fan with low speed
Two 120-Volt GFCI Outlets for accessories and multi-fan connections. To reset, unplug the appliance causing the breaker to trip and push the Reset Button adjacent to the outlets on the Fan.
A ground-fault circuit interrupter detects an abnormal current flow to ground and opens the circuit, preventing a hazardous situation.
If an Outlet stops working, push the button back in to reset the breaker
Specifications
For information about authorized repair and maintenance contact Global Industrial.
Maintenance
- Inspect the electrical cord and wiring for damage or discoloration before use. NEVER use a blower that has a damaged cord to avoid risk of electrical shock or fire.
- Inspect for loose fasteners before each use.
- Clean safety screens of the unit before each use.
- Listen for abnormal sounds and shut unit off immediately upon hearing unusual noises.
- Keep unit clean and free of blockages or obstructions.
- Use compressed air or a vacuum to remove lint and other debris from the motor, inlet, or fan blade.
- Do not use a pressure washer, water hose, or other water source to clean the unit. Ensure that the unit is completely dry before each use.
- The blower has sealed bearings and cannot be lubricated. No oiling is necessary
Optional Bracket
The 641765 air mover can assemble on the bracket [641766] which can let the air mover blow 360° directions.
Use the screw and rubber gasket to fix the air mover on the bracket. Tight the screw by hand to hold the fan firmly on the bracket.
Loose the screw to adjust the air mover blow direction.
The bracket sold separately, item number 641766
Trouble Shooting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>