ScanAvenger Wireless Barcode Scanner User Guide

ScanAvenger Wireless Barcode Scanner

STATE DESCRIPTION

LED Light

• Blue LED ON: Scanner ON and connected
• Red LED ON: Charging
• No light ON: Scanner not connected to any device

Buzzer

• A long beep: Power ON/OFF
• A short beep (low frequency): Scan common barcode, paired, or wireless connection success
• 5 short beeps (low frequency) and stop scanning: Battery without electricity
• 3 short beeps (low frequency): Wireless disconnection

In order to correctly use the barcode scanner, please read the instructions carefully. It is advised to keep this manual for future reference.
No part of this publication may be reproduced or distributed in any form without written permission from ScanAvenger. ScanAvenger reserves the right to make the final interpretation of the above statement.
If you come across any issues with your product, please contact us via email at helpdesk@ccheck.global
When contacting our helpdesk please make sure you mention your order number and scanner model.

• Scanner type: CCD
• Light source: Red Light LED 525 ±10nm
• CPU: 32-bit
• Resolution : 2500
• Resolution: 3mil
• Decoding speed: 300 scans/s
• Depth of field: 30mm-700mm
• Scan mode: Manual, Continuous, Auto Sense
• Scan angle: : ±60˚, Roll: ±30˚, Skew: ±60˚
• Print contrast: ≥20%
• Wireless: 2.4GHz = 150meters, Bluetooth
• distance: 30meters (open distance)
• Storage: 16Mb (over 100,000 Product codes)
• Battery capacity: 2200 mAh
• Charging time: Approx. 3 hours
• Continuous working time: ≥16 hours
• Communication: USB, Wireless 2.4G, Wireless Bluetooth 4.2
• Power supply: DC 5V@130mA (work)
• Operating temp: 0˚ C to 50˚C
• Storage: -30˚C to 60˚C
• Humidity: 5% to 95% (non-condensing)
• Drop Height: 1.5mCE,
• Certificate: FCC, RoHS

For an extended user manual or any questions please email us at helpdesk@ccheck.global

How to connect scanner using USB Wireless Dongle:

1. Power the scanner by pressing the button
2. Insert the USB Dongle in a USB port on the computer
3. Wait 30 seconds for devices to pair automatically and you are ready to go.

• For any issues connecting the scanner to the Wireless USB Dongle please check instructions on page 7 of this manual or email helpdesk@ccheck.gobal for support.
  How to connect scanner via Bluetooth to mobile phone, tablet or other Bluetooth devices:

  1. Hold scanner button pressed for 8 seconds or longer. The light at the back of the scanner will start flashing blue.
  2. When scanner light is flashing blue you can connect it to your mobile device. On your mobile/tablet go to Bluetooth devices, search for “ScanAvanger HID” and click PAIR
  3. You are ready to go.
     Remember you can turn ON/OFF your mobile phone/tablet keyboard by double tapping the scanner button.

To test, open a word document or notes and try scanning a normal barcode (not a configuration barcode from the user guide)
At any point if you wish to exit setup mode double tap the button on the scanner
If you have any questions about setting up or configuring the scanner please email us at helpdesk@ccheck.gobal . Our helpdesk operates 24/7 – 365 days a year.

SLEEP TIME Setting

For an extended user manual or any questions please email us at helpdesk@ccheck.global

Communication Modes
The scanner is by default configured to connect to the dongle.
All you need to do is plug the dongle into a computer and it will connect automatically.
See page 4 of this manual for details.
If you wish to connect the scanner to a Bluetooth device please follow the steps on page 4.
Once your scanner is connected to a Bluetooth device if you wish to change back to Wireless dongle mode all you need to do is scan the below barcode :

If for what ever reason you are having Bluetooth connectivity issues we recommend you remove the scanner from your Bluetooth devices on your mobile and go throug the steps on Page 4 in order to setup the scanner via Bluetooth again.
For Bluetooth SPP and BLE Modes please contact us at helpdesk@ccheck.global
If the barcode scanner works beyond the transmission range, it is recommended to use storage mode.
In storage mode, the scanned data is stored in the internal memory of the scanner automatically.
To enter Storage Mode, scan the below barcode:

Note:
Please ensure that the wireless signal connection is good when the data is uploading.
Data can also be uploaded by using the cable.

For an extended user manual or any questions please email us at helpdesk@ccheck.global

By scanning the “Clear Data” barcode you will permanently remove any barcodes stored on the memory of the scanner.
Make sure you upload them first

If at any stage you accidentally scan configuration codes and the scanner stops working, please scan the below
“Restore Wireless Parameters” code in order to reset all wireless configuration to default settings.

THE ABOVE ONLY RESETS WIRELESS PARAMETERS.
IF YOU WISH TO FULLY RESET
THE SCANNER TO FACTORY SETTINGS
please email helpdesk to receive details on how to do this. It takes only 20 seconds to reset.

Hidden Character Settings
This product supports hiding multiple characters.
We have included hiding up to 4 characters.
If you wish to hide more please contact us.
A: Select if you wish to hide characters from the front or back of the barcode:

B: Select how many characters you wish to hide (scan only 1 barcode)

Case Sensitivity Settings

See below options to change all letter cases of the scanned barcode to uppercase or lowercase

We don’t like chopping down trees to print 100 page+ user manuals that only 1.9% of customers read.
If you need an extended user manual please email us at helpdesk@ccheck.global for a digital copy.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>