hama USB-A 2x Charger Instruction Manual
- June 6, 2024
- Hama
Table of Contents
hama USB-A 2x Charger
Operating instruction
Thank you for choosing a Hama product. Take your time and read the following instructions and information completely. Please keep these instructions in a safe place for future reference. If you sell the device, please pass these operating instructions on to the new owner.
1. Explanation of Warning Symbols and Notes
Risk of electric shock: This symbol indicates product parts energized
with a dangerous voltage of sufficient magnitude to constitute a risk of
electric shock.
Warning: This symbol is used to indicate safety instructions or to draw
your attention to specific hazards and risks.
Note: This symbol is used to indicate additional information or important
notes.
Package Contents
• Travel charger
• These operating instructions
Safety Notes
• Protect the product from dirt, moisture and overheating and use it in dry
rooms only.
• Do not drop the product and do not expose it to any major shocks.
• Do not operate the product outside the power limits given in the
specifications.
• Do not modify the device in any way. Doing so voids the warranty.
• Do not continue to operate the device if it becomes visibly damaged.
• Use the product for its intended purpose only.
• Keep this product, as all electrical products, out of the reach of children!
• Do not use the product in the immediate vicinity of heaters or other heat
sources or in direct sunlight.
• Lay all cables so that they do not pose a tripping hazard.
• Do not bend or crush the cable.
• Always pull directly on the plug when disconnecting the cable, never on the
cable itself.
• Dispose of packaging material immediately according to locally applicable
regulations.
• The product is intended for indoor use only.
• Use the item only in moderate climatic conditions.
• Do not use the product in areas where the use of electronic devices is not
permitted.
• Do not use the product in moist environments and avoid splashes.
Risk of electric shock
• Do not open the device or continue to operate it if it becomes damaged.
• Do not use the product if the AC adapter, adapter cable or power cable is
damaged.
• Do not attempt to service or repair the product yourself. Leave any and all
service work to qualified experts.
Note on Connecting Possible End Devices
• If you wish to connect multiple devices, please ensure that the maximum
current required by the devices does not exceed the maximum output current of
the product.
• Observe the specified input voltage range of the product. The product is not
designed to be used with voltages that deviate from the specified parameters.
Warning
If the product or the end device is visibly damaged, do not proceed with
charging.
Getting Started
Warning
• Only connect the product to a socket that has been approved for the device.
The socket must be installed close to the product and easily accessible.
• Disconnect the product from the network using the power button – if this is
not available, unplug the power cord from the socket.
• When using a multi-socket power strip, make sure that the sum power draw of
all the connected devices does not exceed its maximum throughput rating.
• If you will not be using the product for a long period of time, disconnect
it from mains power.
Observe the information in the operating instructions of the device to be charged. If no explicit instructions are provided, proceed as described below.
• Ensure that the charger, the connection cable and the end device are
compatible while they are not connected to the power supply.
• Plug the device to be charged into the charger. The device to be charged
should be switched off.
• Plug the charger into an appropriate electrical socket/ cigarette lighter
socket.
• The switched-off end device will now be charged.
Troubleshooting
| Error | Solution |
|---|---|
| A connected end device will not charge. | Check whether your end device |
requires a charger with a special pin assignment and whether the charging
current of the charger is sufficient. This information can be found in the
manual for your end device, or you may contact the manufacturer’s customer
service department.
The charger becomes extremely hot and switches off the charging process after
a period
of time.
| Your end device requires a higher charging current than the charger can provide. The charger automatically switches off the charging process to prevent damage to the charger.
Warranty Disclaimer
Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper installation/mounting, improper use of the product or from failure to observe the operating instructions and/or safety notes.
Technical Data
Specifications in accordance with Regulation (EU) 2019/1782
Speci fi cations in accordance with Regulation (EU) 2019/1782
Manufacturer’s name or trade mark, commercial registration number and address| Hama, HRA12159,
Dresdner Str. 9,
86653 Monheim
Model identifier| 178368; 210540-210544
Input voltage| 100 – 240 V
Input AC frequency| 50 / 60 Hz
Output voltage / Output current / Output power| ****
5.0 V DC/ 2.4 A/ 12.0 W
Average active efficiency| 82.8 %
Efficiency at low load (10 %)| 75.8 %
No-load power consumption| 0.07 W
Recycling Information
Note on environmental protection:
After the implementation of the European Directive 2012/19/EU and 2006/66/EU
in the national legal system, the following applies: Electric and electronic
devices as well as batteries must not be disposed of with household waste.
Consumers are obliged by law to return electrical and electronic devices as
well as batteries at the end of their service lives to the public collecting
points set up for this purpose or point of sale. Details to this are defined
by the national law of the respective country.
This symbol on the product, the instruction manual or the package indicates that a product is subject to these regulations. By recycling, reusing the materials or other forms of utilising old devices/Batteries, you are making an important contribution to protecting our environment.