JFA ELETRONICOS Redline Automotive Charger User Manual

October 30, 2023
JFA ELETRONICOS

JFA ELETRONICOS Redline Automotive Charger

JFA ELETRONICOS Redline
Automotive Charger-product

PRESENTATION

The Charging Sources, 60A, 80A, 120A and 200A are high-power power supplies that make it possible to power and charge automotive battery (s), providing a maximum current of 60A, 80A, 120A and 200A respectively at the output and operate in 3 modes:

  • Slow charge mode: Charges the battery in 3 phases, (Elevation, absorption, equalization). Ideal for recharging batteries when they are low on charge, thus achieving maximum charging efficiency without wearing out, which increases battery life.JFA ELETRONICOS Redline Automotive Charger-fig-1
  • Output Voltage Mode (Source): Enables the digital choice of 8 voltage values at the source output (12.6V / 12.8V / 13.0V / 13.2V / 13.8V / 14.0V / 14.2V / 14.4V).
    Auto SCI mode: Mode to be used when the system is on or fast charge in the battery (s), as it will maintain maximum power at the output (14.4V) and will enter the pulsed SCI system, when the battery (s) ( s) are loaded and stay afloat.

INTELLIGENT SLOW LOAD SYSTEM IN 3 PHASES LOW

LOAD MODE OPERATION:

  1. Phase 1 (Elevation): Raises the battery voltage up to 14.4V with a maximum current of 20% of the set battery rating.
    This phase has 8 “steps” which are indicated by the frequency of the F1 led lighting from 1 to 8Hz. When the led lights up constantly, it means that this phase has already been executed.

  2. Phase 2 (Absorption): The voltage remains constant at 14.4, the battery absorbs the load and when the current decreases to 4% of the set battery rating, led F2 lights up constantly, passed to the next phase.

  3. Phase 3 (Equalization): Phase 3 is characterized by the decrease in voltage to 13.8V with pulses of 14.4 every 5 minutes. The battery is charged to its maximum capacity, as the equalization is done in a pulsating manner.
    Conclusion: The discharged battery is charged with 100% charge without suffering heating, which will prolong its useful life, in addition to making it possible to put more charge in it.

SELECTION OF OPERATING MODES

SLOW LOAD MODE:

  1. Press the MODE Selector switch and select SLOW LOAD.

  2. Press the BATTERY Selector switch and select the ampere capacity of the battery to be charged. If there is more than one battery, add them all together and select the bank1s capacity.
    The options are as follows:JFA ELETRONICOS Redline Automotive Charger-
fig-2
    Note 1:
    If your battery does not fit these options, use the closest value.
    Note 2:
    lf there is more than one source in the system, use only one in slow charge mode. All others must be turned off.

  3. When there is a Full Charge indication, the battery (s) will be charged. F1, F2 and F3 indicate what stage the slow charge process is in.

AUTO SCI MODE:
Press the MODE Selector switch and select Auto SCI (Intelligent Charge System). Allows the source output to operate at 14.4V when the system requires more power. In fluctuation, it operates with the output voltage in cycles of 13.8V for 5 minutes and 14.4V for 10 seconds. This system prevents excessive elevation of the potential of the plates, a chemical phenomenon caused by charge stress (electrolysis), increasing the useful life and efficiency of the batteries.

SOURCE MODE:

  1. Press the MODE Selector switch and select Output Voltage.
  2. Press the Voltage Selector switch and select the desired output voltage on the display:JFA ELETRONICOS Redline Automotive Charger-fig-3

PERFORMANCE & INTELLIGENCE

MODE X APPLICATION X ADVANTAGES TABLE **

JFA ELETRONICOS Redline
Automotive Charger-fig-9
**TYPES OF READING

  • Voltage: Informs the voltage sent to the system.
  • Current: Shows the current consumed by the system.
  • Battery check-up: Informs you how much charge has been accumulated by the battery during the charging cycle, with this reading it is possible to know if the battery is in good working order.

The counter can be reset by holding the Read key for 5 seconds. Upon reaching 999, it must be reset to continue reading the accumulated charge on the battery.

IMPORTANT TIPS

  1. Prioritize charging the batteries in slow charge, this way more charge accumulates, besides increasing its useful life.
  2. If the batteries are discharged, charge only in the slow charge mode, thus avoiding wear and excessive heating in them.
  3. We advise that when using the sound, immediately connect the Source in AUTO SCI mode. Do not wait for the batteries to discharge before doing so.
  4. Use 1 outlet per equipment. Each Power Supply 60A, 80A, 120A, and 200A consumes about 900W, 1260W, 1800W and 3000W of the power grid respectively.
  5. Use 1 0mm2 cable at the 60A output, 25mm2 at the 80A output, 35mm2 at the 120A output, and 70mm2 at the 200A output.
  6. Do not install in high-vibration environments such as speakers.

DESCRIPTIONS

  1. Leds that indicate the monitoring of the Voltage or Current or Check-up of the battery “2 led accesses”;
  2. Selector switch for the voltage, current and ampere hour counter reading mode;
  3. Selector switch for the Slow Load, Auto SCI and Output Voltage modes;
  4. LEDs for Slow Charge, Auto SCI and Output Voltage modes;
  5. Battery capacity selector switch (Slow charge mode) or Output voltage (Output voltage mode);
  6. Led indicator for full charge;
  7. LEDs indicating the 3 phases of loading;
  8. Voltage or Current indicator display or Ampere Hour Counter;
  9. Energy entry tail;
  10. Input fuse 15A for the 60A model;
  11. Circuit breaker acting as an on / off switch (models 80A, 120A and 200A);
  12. Output connector;
  13. Air outlet (never obstruct);
  14. Air intake (never obstruct);
  15. 1 0mm2 gauge cable adapter (exclusive for 60A power supply).JFA ELETRONICOS Redline Automotive Charger-fig-4

CONNECTION DIAGRAM

Each CHARGER 60A, 80A, 120A, and 200A can feed about 3,000, 4,000, 6,000 and 10,000 Wrms of sound playing respectively, provided that, using a battery in parallel to supply peak consumption.JFA ELETRONICOS Redline Automotive
Charger-fig-5

You can use as many Sources 60A, 80A, 120A and 200A as necessary to feed the sound, having as reference that each one keeps about 3,000, 4,000, 6,000, and 10,000 Wrms of sound playing respectively, it is important to note that when operating in In parallel, the sources must operate in the same MODES as follows:
Auto SCI: All sources must be in SCI.
Output voltage (Source): All sources must have the same output voltage.
Slow Load: Only one source is turned on, the other sources must be turned off.JFA ELETRONICOS Redline Automotive Charger-fig-6

SSPECIFICATION

JFA ELETRONICOS Redline Automotive Charger-
fig-7
JFA ELETRONICOS Redline Automotive Charger-fig-8

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals