Edge-core AS4630-54PE 48-Port Ethernet Switch Instructions
- June 6, 2024
- Edge-core
Table of Contents
Safety & Regulatory Information
48-Port Ethernet Switch
AS4630-54PE
FCC Class A
This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in
accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is
likely to cause harmful interference in which case the user will be required
to correct the interference at his own expense.
You are cautioned that changes or modifications not expressly approved by the
party responsible for compliance could void your authority to operate the
equipment.
You may use unshielded twisted-pair (UTP) for RJ-45 connections – Category 3
or better for 10 Mbps connections, Category 5 or better for 100 Mbps
connections, Category 5, 5e, or 6 for 1000 Mbps connections. For fiber-optic
connections, you may use 50/125 or 62.5/125 micron multimode fiber or 9/125
micron single-mode fiber.
CE Mark
CE Mark Declaration of Conformance for EMI and Safety (EEC)
This information technology equipment complies with the requirements of the
Council Directive 2014/30/EU on the Approximation of the laws of the Member
States relating to Electromagnetic Compatibility and 2014/35/EU for electrical
equipment used within certain voltage limits. For the evaluation of the
compliance with these Directives, the following standards were applied:
RFI Emission:
- Limit according to EN 55032:2015+AC:2016, Class A
- Limit for harmonic current emission according to EN 61000-3-2:2014, Class A
- Limitation of voltage fluctuation and flicker in low-voltage supply systems according to EN 61000-3-3:2013
Immunity:
- Product family standard according to EN 55024:2010+ A1:2015 and EN 55035:2017
- Electrostatic Discharge according to IEC 61000-4-2:2008 ED. 2.0
- Radio-frequency electromagnetic field according to IEC 61000-4-3:2010 ED. 3.2
- Electrical fast transient/burst according to IEC 61000-44:2012 ED. 3.0
- Surge immunity test according to IEC 61000-4-5:2014 ED. 3.0
- Immunity to conducted disturbances, induced by radiofrequency fields: IEC 61000-4-6:2013 ED. 4.0
- Power frequency magnetic field immunity test according to IEC 61000-4-8:2009 ED. 2.0
- Voltage dips, short interruptions, and voltage variations immunity test according to IEC 61000-4-11:2004 ED. 2.0
LVD:
- EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
- EN 62368-1:2014/A11:2017
The Declaration of Conformity (DoC) can be obtained from www.edge- core.com->support->download.
Japan – VCCI Class A
Laser Safety
Warning: Fiber Optic Port Safety:
When using a fiber optic port, never look at the transmit laser while it is powered on. Also, never look directly at the fiber TX port and fiber cable ends when they are powered on.
PSE Alarm
Power and Battery Safety
**| Warning:** If your device uses a lithium battery, do not attempt to
replace the battery yourself. Return the device to the manufacturer for
battery replacement.
---|---
| If the device contains lithium batteries that are encased in a sealed
chassis, do not attempt to open the sealed chassis under any circumstances.
| Risk of explosion if the battery is replaced by an incorrect type. Dispose
of used batteries according to the instructions.
| Caution – Risk of Electrical Shock: To disconnect power, remove all power cords from the unit.
Power Cord Safety
Please read the following safety information carefully before installing the
switch:
Warning: Installation and removal of the unit must be carried out by qualified
personnel only.
- The unit must be connected to an earthed (grounded) outlet to comply with international safety standards.
- Do not connect the unit to an A.C. outlet (power supply) without an earth (ground) connection.
- The appliance coupler (the connector to the unit and not the wall plug) must have a configuration for mating with an EN 60320/IEC 320 appliance inlet.
- The socket-outlet must be near to the unit and easily accessible. You can only remove power from the unit by disconnecting the power cord from the outlet.
- This unit operates under SELV (Safety Extra Low Voltage) conditions according to IEC 60950. The conditions are only maintained if the equipment to which it is connected also operates under SELV conditions.
France and Peru only
This unit cannot be powered from IT† supplies. If your supplies are of IT
type, this unit must be powered by 230 V (2P+T) via an isolation transformer
ratio 1:1, with the secondary connection point labeled Neutral, connected
directly to earth (ground).
Important! Before making connections, make sure you have the correct cord set. Check it (read the label on the cable) against the following:
Power Cord Set
The U.S.A. and Canada| The cord set must be UL-approved and CSA certified.
The minimum specifications for the flexible cord are:
– No. 14 AWG – not longer than 4.5 meters. type SJE, SJT, or ST.
– No. 14 AWG – not longer than 2.4 meters, type SVT orSPT-2.
– 3-conductor.
The cord set must have a rated current capacity of at least 15 A.
The attachment plug must be an earth-grounding type with NEMA 5-15P (15 A, 125
V) configuration.
Denmark| The supply plug must comply with Section 107-2-D1, Standard DK2-1a,
or DK2-5a.
Switzerland| The supply plug must comply with SEV/ASE 1011.
The U.K.| The supply plug must comply with BS1363 (3-pin 13 A) and be fitted
with a 5 A fuse which complies with BS1362.
The main cord must comply with IEC 60227 (designation 60227 IEC 52).
Europe| The supply plug must comply with CEE7/7 (“SCHUKO”).
The main cord must comply with IEC 60227 (designation 60227 IEC 52).
IEC-320 receptacle.
Warnings and Cautionary Messages
| Warning: This product does not contain any serviceable user parts.
Warning: Installation and removal of the unit must be carried out by
qualified personnel only.
Warning: When connecting this device to a power outlet, connect the field
ground lead on the tri-pole power plug to a valid earth ground line to prevent
electrical hazards.
Warning: This switch uses lasers to transmit signals over fiber optic
cable. The lasers are compliant with the requirements of a Class 1 Laser
Product and are inherently eye safe in normal operation. However, you should
never look directly at a transmit port when it is powered on.
Warning: When selecting a fiber SFP/SFP+/QSFP+ device, considering
safety, please make sure that it can function at a temperature that is not
less than the recommended maximum operating temperature of the product. You
must also use an approved Laser Class 1 SFP/SFP+/QSFP+ transceiver.
---|---
| Caution: Wear an anti-static wrist strap or take other suitable
measures to prevent electrostatic discharge when handling this equipment.
Caution: Do not plug a phone jack connector in the RJ-45 port.
This may damage this device.
Caution: Use only twisted-pair cables with RJ-45 connectors that conform
to FCC standards.
Caution: The switch includes a plug-in power supply (PSU) and fan tray
modules that are installed into its chassis. All installed modules must have a
matching airflow direction. That is, if the installed power modules have a
front-to-back (F2B) airflow direction, all the installed fan tray modules must
also have an F2B airflow direction.
Equipment Name| Type Designation (Type)
Unit| Restricted substances and their chemical symbols
(Pb)| (Hg)| (Cd)| (Cr+6)| PBB)| (PBDE)
PCBA| –| | | | |
Fan| –| | | | |
Heatsink| | | | | |
Chassis| –| | | | |
Cable Assembly| | | | | |
Power cord| | | | | |
Power Supply| –| | | | |
Note 1: “Exceeding 0.1 wt %” and “exceeding 0.01 wt %” indicates that the
percentage content of the restricted substance exceeds the reference
percentage value of the present condition.
Note 2: ” ” indicates that the percentage content of the restricted substance
does not exceed the percentage of the reference value of presence.
Note 3: The ” ” indicates that the restricted substance corresponds to the
exemption.
Products contain hazardous substances exposing table
Component Name| Hazardous Substances Project
(Pb)| (Cd)| (Hg)| (Cr6+)| (PBB)| (PBDE)
SSD Module| | | | | |
SDRAM Module| | | | | |
Diode| | | | | |
Mosfet| | | | | |
Crystal| | | | | |
Regulator| | | | | |
Fan| | | | | |
Screw| | | | | |
Spacer| | | | | |
Stand| | | | | |
Power supply| | | | | |
Resistor| | | | | |
SJ/T: 11364-2014
: GB/T 26572-2011
: Indicates the toxic or hazardous substance content of the part (at the
homogenous material level) is lower than the threshold defined by Requirements
for Concentration Limits for Toxic or hazardous Substances in Electronic
Information Products (GB/T 26572-2011) issued by the Chinese Ministry of
Information Industry (“Not Contained” toxic or hazardous substances).
: GB/T 26572-2011
: Indicates the toxic or hazardous substance content of the part (at the
homogenous material level) is over the threshold defined by the standard of
GB/T 26572-2011 (“Contained” toxic or hazardous substances). Suppliers can
explain the technical cause of “X” according to the actual situation.
The Environment- Friendly Use Period (EFUP) for all enclosed products and their parts are per the symbol shown here unless otherwise marked. Certain parts may have a different EFUP (for example, battery modules) and so are marked to reflect such. The Environment- Friendly Use Period is valid only when the product is operated under the conditions defined in the product manual.
Warranty Information and Technical Support
To register your Edgecore product and review a detailed warranty statement,
refer to the Edgecore Networks website at www.edge-core.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>