NOCO GBX55 Lithium booster User Guide
- June 4, 2024
- NOCO
Table of Contents
NOCO GBX55 Lithium booster User Guide
Symbol Description
- DANGER
- READ AND UNDERSTAND ALL SAFETY INFORMATION BEFORE USING THIS PRODUCT. Failure to follow these safety instructions may result in ELECTRICAL SHOCK, EXPLOSION, FIRE, which may result in a SERIOUS INJURY, DEATH, or PROPERTY DAMAGE.
- Electrical Shock. Product is an electrical device that can shock and cause serious injury. Do not cut power cords. Do not submerge in water or get wet.
- Explosion. Unmonitored, incompatible, or damaged batteries can explode if used with product. Do not leave product unattended while in use. Do not attempt to jump start a damaged or frozen battery. Use product only with batteries of recommended voltage. Operate product in well ventilated areas.
- Fire. Product is an electrical device that emits heat and is capable of causing burns. Do not cover product. Do not smoke or use any source of electrical spark or fire when operating product. Keep product away from combustible materials.
- Eye Injury. Wear eye protection when operating product. Batteries can explode and cause flying debris. Battery acid can cause eye and skin irritation. In the case of contamination of eyes or skin, flush affected area with running clean water and contact poison control immediately.
- Explosive Gases.**** Working in the vicinity of a lead-acid is dangerous. Batteries generate explosive gases during normal battery operation. To reduce risk of battery explosion, follow all safety information instructions and those published by the battery manufacturer and manufacturer of any equipment intended to be used in the vicinity of battery. Review precautionary markings on these products and on engine.
Important Safety Warnings
CAUTION:
Manual Override Mode disables all safety measures. When used improperly and/or
against our recommended use, it may result in injury or death and will void
your warranty. Risk of fire, explosion, and burns. Do not disassemble, crush,
heat above 60ºC (140ºF) or incinerate. This device is intended for temporary
use outdoors and reasonable care should be exercised when using this device in
wet conditions.
WARNING:
Do not overcharge the internal battery. See Instruction Manual. Do not smoke,
strike a match, or cause a spark in the vicinity of the power pack. Only
charge the internal battery in a well ventilated area when not in use.
CAUTION:
Risk of Injury To Persons. Do not use this product if the power cord or the
battery cables are damaged in any way. This device is not intended for use in
a commercial repair facility. This device is intended to be stored indoors
when not in use. This device shall not be stored or left outdoors when not in
use.
Proposition 65. Battery posts, terminals, and related accessories contain
chemicals, including lead. These materials are known to the State of
California to cause cancer and birth defects and other reproductive harm.
Personal Precaution. Only use product as intended. Someone should be
within range of your voice or close enough to come to your aid in case of
emergency. Have a supply of clean water and soap nearby in the case of battery
acid contamination. Wear complete eye protection and protective clothing while
working near a battery. Always wash hands after handling batteries and related
materials. Do not handle or wear any metal objects when working with batteries
including; tools, watches or jewelry. If metal is dropped onto battery, it may
spark or create a short circuit resulting in electrical shock, fire, explosion
which may result in injury, death or property damage. Minors. If the
product is intended by «Purchaser» to be used by a minor, purchasing adult
agrees to provide detailed instructions and warnings to any minor prior to
use. Failure to do so is the sole responsibility of the «Purchaser,» who
agrees to indemnify NOCO for any unintended use or misuse by a minor.
Choking Hazard. Accessories may present a choking hazard to children. Do
not leave children unattended with product or any accessory. The product is
not a toy. Handling. Handle product with care. The product can become damaged
if impacted. Do not use a damaged product, including, but not limited to,
cracks to the casing or damaged cables. Do not use product with a damaged
power cord. Humidity and liquids may damage product. Do not handle product or
any electrical components near any liquid. Store and operate product in dry
locations. Do not operate product if it becomes wet. If product is already
operating and becomes wet, disconnect it from the battery and discontinue use
immediately. Do not disconnect the product by pulling on the cables.
Caution: Hot surface, Wait for the unit to cool down before handling.
Modifications. Do not attempt to alter, modify or repair any part of the
product. Disassembling product may cause injury, death or damage to property.
If product becomes damaged malfunctions or comes in contact with any liquid,
discontinue use, and contact NOCO. Any modifications to the product will void
your warranty. Accessories. This product is only approved for use with
NOCO accessories. NOCO is not responsible for user safety or damage when using
accessories not approved by NOCO. Location. Prevent battery acid from
coming in contact with the product. Do not operate the product in a closed-in
area or an area with restricted ventilation. Do not set a battery on top of
product. Position cable leads to avoid accidental damage by moving vehicle
parts (including hoods and doors), moving engine parts (including fan blades,
belts, and pulleys), or what could become a hazard that may cause injury or
death. Operating Temperature. This product is designed to work in ambient
temperatures between -20º C to 50º C. Do not operate outside of temperature
ranges. Do not jump start a frozen battery. Discontinue use of product
immediately if the battery becomes excessively warm. Storage. Do not use
or store your product in areas with high concentrations of dust or airborne
materials. Store your product on flat; secure surfaces so it’s not prone to
falling. Store your product in a dry location. The storage temperature is
-20ºC to +50ºC (0ºC ~ +25ºC daily average). Never exceed 80ºC under any
condition. Compatibility. The product is only compatible with 12-volt lead-
acid batteries only. Do not attempt to use product with any other type of
battery. Jump starting other battery chemistries may result in injury, death
or property damage. Contact the battery manufacturer prior to attempting to
jump start the battery. Do not jump start a battery if you are unsure of the
battery’s specific chemistry or voltage. The Battery. The built-in
lithium-ion battery in the product should be replaced only by NOCO, and must
be recycled or disposed of separately from household waste. Do not attempt to
replace the battery yourself and do not handle a damaged or leaking lithium-
ion battery. Never dispose of battery in household trash. Disposal of
batteries in household trash is unlawful under state and federal environmental
laws and regulations. Always take used batteries to your local battery
recycling center. If the product battery is excessively hot, emitting an odor,
deformed, cut, or is experiencing or demonstrating an abnormal occurrence,
immediately stop all use and contact NOCO. Battery Charging. Charge the
product with the included USB-C charging cable. NOCO is not responsible for
damage, injury, and/or death while using non-approved, third-party charging
products. Be cautious of using low quality power adaptors, as they may present
a serious electrical risk that can result in injury and/or death to person,
device, and property. Using damaged cables or chargers, or charging when
moisture is present, can result in electric shock. Using generic or third-
party power adapter may shorten the life of your product and cause the product
to malfunction. NOCO is not responsible for the user’s safety when using
accessories or supplies that are not approved by NOCO. When using a USB power
adapter to charge the product, make sure that the AC plug is fully inserted
into the adapter before you plug it into a power outlet. Power adapters may
become warm during normal use, and prolonged skin contact may cause bodily
injury. Always allow adequate ventilation around power adapters when using
them. To ensure maximum battery life, avoid charging your product for more
than a week at a time, as overcharging may shorten battery life. Over time, an
unused product will discharge and must be recharged before use. Disconnect the
product from power sources when not in use. Use the product only for their
intended purposes. Medical Devices. Product may emit electromagnetic
fields. Product contains magnetic components which may interfere with
pacemakers, defibrilators, or other medical devises. These electromagnetic
fields may interfere with pacemakers or other medical devices. Consult with
your physician prior to use if you have any medical device including
pacemakers. If you suspect the product is interfering with a medical device,
stop using the product immediately and consult your physician. Medical
Conditions. If you have any medical condition that you believe could be
affected by product, including but not limited to; seizures, blackouts,
eyestrain or headaches, consult your physician prior to use of product. The
use of a integrated high-powered flashlight contains a light sensitivity
hazard. Use of the light in Strobe Mode may cause seizures in persons with
photosensitive epilepsy, which may result in serious injury or death. Light.
Staring directly into the light beam or shine of the flashlight may result in
permanent eye injury. The product is equipped with a high output LED pre
focused lamp that emits a powerful beam at the highest setting. Cleaning.
Power off the product before attempting any maintenance or cleaning. Clean and
dry product immediately if it comes in contact with liquid or any type of
contaminant. Use a soft, lint-free (microfiber) cloth. Avoid getting moisture
in openings. Explosive Atmospheres. Obey all signs and instructions. Do not
operate product in any area with a potentially explosive atmosphere, including
fueling areas or areas which
contain chemicals or particles such as grain, dust or metal powders. High
Consequence Activities. This product is not intended for use where the
failure of the product could lead to injury, death or severe environmental
damage. Radio Frequency Interference. Product is designed, tested, and
manufactured to comply with regulations governing radio frequency emissions.
Such emissions from the product can negatively affect the operation of other
electronic equipment, causing them to malfunction. Model Number: GBX55 This
device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation. NOTE: This equipment has
been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be required to correct
the interference at his own expense.
How To Use
Step 1: Charge the GBX55
The GBX55 comes partially charged out of the box and needs to be fully charged
prior to use. Connect the GBX55 using the included USB-C Charge Cable to the
USB-C IN/OUT port. It can be recharged from any powered USB port, like an AC
adapter, car charger, laptop and more. The USB-C IN/OUT port utilizes Power
Delivery 3.0 technology capable of receiving/delivering up to 60W. The time to
recharge a GBX55 will differ based on the discharge level and the power source
used. Actual results may vary due to battery conditions.
Recharge Time:
|
Charger Rating:
---|---
28h
|
2.5W
14h
| 5W
7.2h|
10W
When recharging, the charge level of the internal battery is indicated by the charge LEDs. The LEDs will slowly pulse ‘on’ and ‘off’ and become solid until all four charge LEDs are on. When the battery is fully charged, the green 100% LED will be solid, and the 25%, 50% and 75% charge LEDs will turn «off». From time to time, the green 100% LED will pulse indicating maintenance charging is occuring.
Fast Charge.
The GBX55 is equipped with fast charging technology that allows it to be
recharged at a rate of up to 60W. A compatible charger, capable of 60W USB-C
Power Delivery 3.0, is required to fully utilize this feature. The fast charge
LED will illuminate when rate of charge exceeds 15W, indicating USB Power
Delivery 3.0 is active.
Fast Charge:
Recharge Time:
|
Charger Rating:
---|---
1.2|
60W
Auto Charger
The most effective way to charge GBX55 is by using The NOCO Auto Charger (not
included).
NOTE: The vehicle must be On / Running for the Auto Charger to Fast
Charge the unit.
Power Source
When charging USB devices, it is important to power on the GBX55 unit first
and then plug in the USB device being charged.
NOTE: If the GBX55 unit is not powered on first, it will drain power from the USB device, if it is DRP compatible. To charge GBX55 with a DRP compatible device (e.g phone, laptop, power bank) ensure GBX55 is powered OFF before making a cable connection between GBX55 and the DRP device.
Auto Charger:
Recharge Time:
|
Charger Rating:
---|---
1.2|
60W
Step 2: Connect to the Battery.
Carefully read and understand the vehicle owner’s manual on specific
precautions and recommended methods for jump starting the vehicle. Make sure
to determine the voltage and chemistry of the battery by referring to your
battery owner’s manual prior to using this product. The GBX55 is for jump
starting 12-volt lead-acid batteries only. Before connecting to the battery,
verify that you have a 12-volt lead-acid battery. The GBX55 is not suitable
for any other type of battery. Identify the correct polarity of the battery
terminals on the battery. The positive battery terminal is typically marked by
these letters or symbol (POS,P,+). The negative battery terminal is typically
marked by these letters or symbol (NEG,N,-). Do not make any connections to
the carburetor, fuel lines, or thin, sheet metal parts. The below instructions
are for a negative ground system (most common). If your vehicle is a positive
ground system (very uncommon), follow the below instructions in reverse order.
- Connect the positive (red) battery clamp to the positive (POS,P,+) battery terminal and the negative (black) battery clamp to the negative (NEG,N,-) battery terminal or vehicle chassis.
Step 3: Jump Starting
- Make sure all of the vehicle’s power loads (headlights, radio, air conditioning, etc.) are turned off before attempting to jump start the vehicle.
- Press the power button to begin jump starting, and all LEDs will flash once. If you are properly connected to the battery, the white boost LED will illuminate and the battery charge LEDs will chase. A 60-second timeout countdown will begin as soon as a battery is detected.
- Try starting the vehicle. Most vehicles will immediately start. If the vehicle does not start right away, wait 20-30 seconds and try again. After the 60-second timeout is complete, the unit must be powered off, then back on, to initiate a new jump-start sequence. Do not attempt more than five (5) consecutive jump starts within a fifteen (15) minute period. Allow the GBX55 to rest for fifteen (15) minutes before attempting to jump start the vehicle again.
- Once you have started your vehicle, power off the unit, disconnect the battery clamps, and remove the GBX55.
60-Second Timeout.
A 60-second countdown will be initiated as soon as a battery is detected.
After 60 seconds has elapsed, the jump starting function will be disabled. The
boost LED will turn off and the internal battery charge LEDs will indicate the
current charge level of the unit. To reset the jump-starting function, press
the power button to power off the unit. Press the power button again to power
on the unit and restart the jump starting function.
CAUTION.
60-SECOND TIMEOUT IS DISABLED WHILE USING MANUAL OVERRIDE MODE. POWER WILL
CONTINUE TO BE SUPPLIED WHILE MANUAL OVERRIDE IS ACTIVE. TO MAXIMIZE THE
NUMBER OF JUMP-STARTS, IT IS RECOMMENDED TO TURN OFF THE BOOST-UNIT AS SOON AS
THE VEHICLE HAS STARTED.
Low Voltage Batteries & Manual Override.
The GBX55 is designed to jump start 12-volt lead-acid batteries down to 3
volts. If your battery is below 3-volts, the Boost LED will be «off». This is
an indication that the GBX55 can not detect a battery. If you need to jump
start a battery below 3-volts there is a manual override feature, which allows
you to force «on» the jump start function.
CAUTION.
USE THIS MODE WITH EXTREME CARE. THIS MODE IS FOR 12-VOLT LEAD-ACID BATTERIES
ONLY. BOTH THE SPARK PROOF AND REVERSE POLARITY PROTECTION FEATURES ARE
DISABLED. PAY VERY CLOSE ATTENTION TO THE POLARITY OF THE BATTERY BEFORE USING
THIS MODE. DO NOT ALLOW THE POSITIVE AND NEGATIVE BATTERY CLAMPS TO TOUCH OR
CONNECT TO EACH OTHER AS THE PRODUCT WILL GENERATE SPARKS. THIS MODE USES VERY
HIGH CURRENT (UP TO 1750 AMPS) THAT CAN CAUSE SPARKS AND HIGH HEAT IF NOT USED
PROPERLY. IF YOU ARE UNSURE ABOUT USING THIS MODE, DONOT ATTEMPT AND SEEK
PROFESSIONAL HELP.
Interface
-
Power LED Illuminates White when unit is “On”. Will illuminate orange after the 60-second timeout countdown until the clamps are removed from the Car Battery or the GBX55 is power cycled ‘off’ and back ‘on’ again.
-
Power Button Push to turn unit “on” & “off” or restart boost after 60-second timeout.
-
Reverse Polarity Error LED Illuminates red if reverse polarity is detected.
-
Cold LED Illuminates solid or flashes blue when internal temperature is too low.
-
Hot LED Illuminates solid or flashes red when internal temperature is too high.
-
Error LED Blinks “on” and “off” in various sequences (from 1 to 6 blinks) to convey error conditions.
-
Internal Battery Level Indicates the charge level of the internal battery.
-
Light Mode Button Toggles the ultra-bright LED light through 7 light modes: 100% >50% > 10% > SOS > Blink > Strobe > Off.
-
Boost LED Illuminates white when boost is active. If the unit is connected properly to a battery, the GBX55 will automatically detect a battery and go into boost mode (LED flashes white when manual override feature is active).
-
Manual Override Button To enable, push and hold for three (3) seconds.
WARNING: Disables safety protection and manually forces Boost «On».Only for use when a battery voltage is too low to be detected. -
Fast Charge LED Illuminates white when fast charge is active. Fast charge LED turns red (solid/blinking) when there is an error.
Troubleshooting
Error|
Reason/Solution
---|---
| Solid Red| Reverse polarity detected. / Reverse the battery connections.
| Single (1) Flash| Short circuit detected on battery clamps. / Remove all
loads, reconnect clamps to battery.
Double (2) Flash| High voltage detected at clamps (the GBX55 is connected to a
voltage system greater than 12V, such as 24V).
Triple (3) Flash| Bad battery cell detected. / When an internal battery cell
has failed during charging.
Quadruple (4) Flash| Charge timeout error (i.e. the GBX55 has been in bulk
charge for too long).
Sextuple (6) Flash| Back-Charge detected into the GBX55 through the clamps
while in a Boost Mode (i.e. the GBX55 is in Manual Override and then connected
to a system greater than 12V, such as 24V).
| Hot LED: Solid| Unit is fully operational, but approaching upper temperature
limit. / Allow the unit to cool.
Hot LED: Flashing| Unit is too hot to jump start, only the flashlight is
available in this state. / Allow the unit to cool.
| Cold LED: Solid| Unit is fully operational, but approaching lower
temperature limit. / Allow the unit to warm up.
Cold LED: Flashing| Unit is too cold to jump start, only the flashlight is
available in this state / Allow the unit to warm up.
| Flashing Red| If charging the unit, check the cable or charger for damage /
If charging a USB-C device, check cable or device for damage / If problem
persists, contact NOCO support.
Solid Red| Connected Charger is Incompatible. / Unplug USB Cable, Turn Off/On
the Unit, Use Different Charger.
Technical Specifications
- Internal Battery: 46Wh Lithium Ion
- Peak Current Rating: 1750A
- Operating Temperature: -20°C to +50°C
- Charging Temperature: 0ºC to +40ºC
- Storage Temperature: -20ºC to +50ºC (avg Temp.)
- USB-C (In): 5V 1.5A/9V 3A/12V 3A/15V 3A/20V 3A
- USB-C (Out): 5V 3A/9V 3A/12V 3A/15V 3A/20V 3A
- USB (Output): 5VDC 2.1A Max / 10W Max
- Housing Protection: IP65 (w/Ports Closed)
- Cooling: Natural Convection
- Dimensions (L x W x H): 7.7 x 4.9 x 2.5 Inches
- Weight: 2.58 Pounds
NOCO One (1) Year Limited Warranty.
NOCO warrants that this product (the “Product”) will be free from defects in material and workmanship for a period of One (1) Year from the date of purchase (the “Warranty Period”). For defects reported during the Warranty Period, NOCO will, at its discretion, and subject to NOCO’s technical support analysis, either repair or replace defective products. Replacement parts and products will be new or serviceably used, comparable in function and performance to the original part and warranted for the remainder of the original Warranty Period.
NOCO’S LIABILITY HEREUNDER IS EXPRESSLY LIMITED TO REPLACEMENT OR REPAIR. TO THE MAXIMUM EXTENT PERMITTED BY LAW, NOCO SHALL NOT BE LIABLE TO ANY PURCHASER OF THE PRODUCT OR ANY THIRD PARTY FOR ANY SPECIAL, INDIRECT, CONSEQUENTIAL OR EXEMPLARY DAMAGES, INCLUDING, BUT NOT LIMITED TO, LOST PROFITS, PROPERTY DAMAGE OR PERSONAL INJURY, RELATED IN ANY WAY TO THE PRODUCT, HOWSOEVER CAUSED, EVEN IF NOCO HAD KNOWLEDGE OF THE POSSIBILITY OF SUCH DAMAGES. THE WARRANTIES SET FORTH HEREIN ARE IN LIEU OF ALL OTHER WARRANTIES, EXPRESS, IMPLIED, STATUTORY OR OTHERWISE, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, AND THOSE ARISING FROM COURSE OF DEALING, USAGE OR TRADE PRACTICE. IN THE EVENT THAT ANY APPLICABLE LAWS IMPOSE WARRANTIES, CONDITIONS OR OBLIGATIONS THAT CANNOT BE EXCLUDED OR MODIFIED, THIS PARAGRAPH SHALL APPLY TO THE GREATEST EXTENT ALLOWED BY SUCH LAWS.
This Warranty is made solely for the benefit of the original purchaser of the Product from NOCO or from a NOCO approved reseller or distributor and is not assignable or transferable. To assert a warranty claim, the purchaser must: (1) request and obtain a return merchandise authorization (“RMA”) number and return location information (the “Return Location”) from NOCO Support by emailing support@no.co or by calling 1.800.456.6626; and (2) send the Product, including RMA number, and receipt to the Return Location. DO NOT SEND IN PRODUCT WITHOUT FIRST OBTAINING AN RMA FROM NOCO SUPPORT. THE ORIGINAL PURCHASER IS RESPONSIBLE (AND MUST PREPAY) ALL PACKAGING AND TRANSPORTATION COSTS TO SHIP PRODUCTS FOR WARRANTY SERVICE. NOTWITHSTANDING THE ABOVE, THIS HASSLE-FREE WARRANTY IS VOID AND DOES NOT APPLY TO PRODUCTS THAT:
- (a) are misused, mishandled, subjected to abuse or careless handling, accident, improperly stored, or operated under conditions of extreme voltage, temperature, shock, or vibration beyond NOCO’s recommendations for safe and effective use;
- (b) improperly installed, operated or maintained; (c) are/were modified without the express written consent of NOCO;
- (d) have been disassembled, altered or repaired by anyone other than NOCO;
- (e) the defects of which were reported after the Warranty Period.
THIS HASSLE-FREE WARRANTY DOES NOT COVER: (1) normal wear and tear; (2) cosmetic damage that does not affect functionality; or (3) Products where the NOCO serial number is missing, altered, or defaced.
HASSLE-FREE WARRANTY CONDITIONS
These conditions apply only to product during the warranty period. The Hassle-
Free Warranty is void either by elapsed time from date of purchase (elapsed
time from serial number date, if no proof of purchase) or from the conditions
listed earlier in this document. Return product with the appropriate
documentation.
With Receipt:
1 Year: No charge. With proof of purchase, The warranty period begins on
date of purchase
With NO Receipt:
1 Year: No charge. With no proof of purchase, the warranty period begins
on the serial number date.
We recommend registering your NOCO product in order to upload proof of purchase and extend your effective warranty dates. You may register your NOCO product online at: no.co/register. If you have any questions regarding your warranty or product, contact NOCO Support (email and phone number above) or write to: The NOCO Company, at 30339 Diamond Parkway, #102, Glenwillow, OH 44139 USA.
For more information and support visit:
www.no.co/support
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>