Milesight DeviceHub Installation Guide
- June 6, 2024
- Milesight
Table of Contents
Milesight DeviceHub
Installation Guide
Xiamen Milesight IoT Co., Ltd.
Preface
This guide teaches you how to install the Milesight on-premises DeviceHub platform.
Readers
This guide is intended for the following users:
- Distributors
- Network Planners
- On-site technical support and maintenance personnel
- Network administrators responsible for network configuration and maintenance
Copyright © 2011-2021 Milesight. All rights reserved.
All information in this guide is protected by copyright law. Whereby, no
organization or individual shall copy or reproduce the whole or part of this
user guide by any means without written authorization from Xiamen Milesight
IoT Co., Ltd.
| For assistance, please contact
Milesight technical support:
Email: iot.support@milesight.com
Tel: 86-592-5085280
Fax: 86-592-5023065
Address: 4/F, No.63-2 Wanghai Road,
2nd Software Park, Xiamen, China
---|---
Revision History
| Date | Doc Version | Description |
|---|---|---|
| Aug. 29, 2018 | V 1.0 | Initial version |
| Mar. 18, 2021 | V 2.0 | Brand Replace and add features |
Introduction
Milesight DeviceHub provides a high-efficiency, low maintenance solution to easily deploy Milesight IoT devices across multiple locations, reducing complexity and increasing productivity. Milesight offers cloud and on-premises versions according to customer requirements. This guide will describe how to install on-premises DeviceHub. For the cloud version please contact Milesight IoT sales or click here to apply for a DeviceHub Cloud platform account.
**System Requirements
**
Hardware
It’s suggested to use the server which suits the following requirements:
For 500 devices
-
CPU: 2 Cores, 2.0 GHz
-
RAM: 16 GB
-
Disk: 512 GB
-
Bandwidth: ≥100MBps
For 1000 devices -
CPU: 8 Cores, 3.2 GHz
-
RAM: 32 GB
-
Disk: 1 TB
-
Bandwidth: ≥100MBps
Software
- Operating System: Ubuntu 16.04
- Browser: Chrome, Firefox
Installation
Requirements
- Ubuntu Server
- DeviceHub Software Package
- WinSCP
- Putty (or another SSH tool)
Package Upload
Following steps are based on the WinSCP tool. You can also use other tools to upload packages.
-
Download the DeviceHub package from the Milesight IoT website， then extract and check files:
-
Open WinSCP and set up a session between WinSCP and the server.
-
Select the DeviceHub folder and click “Upload”, select the server path and click “OK” to upload.
DeviceHub Installation
-
Log in to the server via Putty. You can also use other SSH tools.
-
Run following commands under the DeviceHub directory.
chmod +x depend_install_devicehub.sh
./depend_install_devicehub.sh
-
Install DeviceHub software. Take the 2.1.3 version as example, please type the following command: dpkg -I devise hub 2.1.3 amd64.deb
The network interface of this server will show. Select and type the main interface name, then click Enter to start the installation.
It will take about 30 minutes to complete the installation and there will show the following message when the installation is complete.
Registration
After installation, open the browser and type the IP address to open the
registration page. Fill in the following information and click “Install” to
complete the registration.
-
Administrator Account(Required)
Admin Email: the email address working as the root account of the DeviceHub
Password: define the password of the root account -
Outgoing Mail Server(Option)
SMTP Email: Email address used for sending alarm emails or sub-account activation emails
Password: Password of the email address
Server: SMTP server address for email service
Port: SMTP server port for email service
Security: encryption mode for email service
After completing all information, click “TEST” to check if your outgoing mail server is valid. If yes, a SUCCESS prompt will show and DeviceHub will save the email settings.
Otherwise, there is an error message “Authentication failed”.
Note:
- Outgoing mail server information is an option and you can click “Install” to skip the configurations.
- You can also log in to the DeviceHub via administrator account and go to “Settings > Email” to configure or change the outgoing mail server settings.
- If the outgoing mail server is not verified by the “TEST” button, it will not be saved.
After registration, you can log in to the DeviceHub via an administrator account.
Services and Ports
| Port | Protocol | Description |
|---|---|---|
| 22 | TCP | SSH Service |
| 80 | TCP | NGINX Agent(Non-encrypted) |
| 443 | TCP | NGINX Agent(Encrypted) |
| 3478 | UDP | STUND Service |
| 3479 | UDP | STUND Service |
| 6379 | TCP | Message Broker |
| 8080 | TCP | TR069 Service(Non-encrypted) |
| 8443 | TCP | TR069 Service(Encrypted) |
| 10000-10100 | TCP | Remote Access Service |
| 20000-20100 | TCP | Remote Access Service |
Expand Manage Devices
The number of available managing devices can be checked in the “Settings >
General” tab. The maximum number of managing devices is 25 by default for the
on-premises version. Please refer to following
steps to expand manage devices.
- Log in DeviceHub with root account and go to the “Settings > General” tab, then click “Create&Download” to download the license info file.
- Contact Milesight sales or technical support and send the license info file.
- Get an expanded license from Milesight and click “Browse” to import the license.
- Click “Save” to save the settings and the max manageable devices will change.
-END-
Milesight loT
www.milesight-iot.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>