MORRIS MHR-20044S Oil Radiator User Manual
- June 6, 2024
- MORRIS
Table of Contents
MORRIS MHR-20044S Oil Radiator
NOTE: The environment that appears is indicative and may change to some upgrade as part of the ongoing improvement of this experience
REGISTRATION TO THE APPLICATION
1. Press button ‘Register’ to create a new account
2. Press ‘Agree’ for Privacy Policy, to continue.
3. Enter your email or your mobile telephone number to get verification code
and press ‘Get verification Code’.
When you receive verification code, type it to the spaces and create a
password before you press to confirm ‘Done’.
Note: the verification code will be sent to you either at your mobile or
at your email, depending on which registration way you chosein the beginning.
NETWORK SETTINGS
You can be connected to the App using one of these ways:
- Add manually, or
- Search by device
Before you begin network setting progress, make sure the device is as closer as it can be to the Wifi router.
Introduction to connection mode
The device connects automatically to Wifi right after switch on. If this does not happen, press for 3 seconds buttons b, d, e (image 1).
Manual connection through ‘Add Manualy’ mode
Before you begin the connection procedure, make sure the Wifi connection of
the device is activated and that the indicative light flashes.
If not, press button 1 for 1 second while checking that your mobile is connected to Wifi network.
Enter the App and press button + to add your device.
- Press up left ‘Add Manually’.
- In vertical menu on the left, select ‘Small Home Appliances’.
- Chose the device’s type Heater.
Note 1: In case you have activated Bluetooth, the device will automatically appear on your screenas ‘Device to be added’ .
Note 2: the photo is just indicative, it is possible the category and / or the device’s type may appear in anotherplace of your screen.
Make sure the WiFi indicator light flashes.
If not, press buttons b, d, e for 3 seconds (image 1).
Select your Home Network, enter your password and press ‘Confirm’.
All settings will be transfered to your device.
Please wait till the connection with the device is successfully added.
If connection fails, try again.
If connection fails again, please check ‘Troubleshooting’ chapter for further
assistance.
Once the connection is done, the device will appear on your screen.
Press button ‘Done’ to complete procedure.
Automatic connection through ‘Search for Device’ mode
Before you begin the connection procedure, make sure the Wifi connection of the device is activated and that the indicative light flashes.
Press up right ‘Search for Device’. Make sure the Access Location is activated and press WiFi activation button ‘Enable Wi-Fi’ to be connected.
Make sure the WiFi indicator light flashes to the device, then press to start scanning ‘Configuring Wi-Fi’ choice.
Your home network should appear on the screen now. At this same network you
must have connected your mobile also. Enter your password and press’Confirm’
button.
Important Notice: Only 2.4GHz networks are supported.
At this point, begins searching the device.
If searching procedure fails, please try again.
If it fails again, please check ‘Troubleshooting’ chapter for further
assistance.
Once searching procedure is done, the device will appear on your screen as
‘available’.
Press button ‘Next’ to complete connection procedure.
Device control environment
- Press buttons ‘+ / -‘ to increase / reduce temperature settings of the device.
- On your screen you can see the recent temperature.
- Press button to activate / de-activate the device.
- Press ‘Function’ button to set speed of the device (ECO, Levels 1, 2, 3).
- Press ‘Settings’ button to control other functions (Timer, Child-lock etc.).
Settings screen
Timer settings
- Chose the time you wish to activate / deactivate the device.
- Chose to repeat the settings for specific days.
- Chose timer’s action: Activate or deactivate.
Troubleshooting
- Check if the device is activated and in Stand-By mode. If not, activate it and press buttons b, d, e (image1) for about 5 seconds. When WiFi function is activated, the indicative light flashes rapidly.
- Make sure the WiFi password has ben typed correctly (capitals and / or lowercase letters considered as different).
- Make sure your telephone is properly connected to WiFi Network.
- Make sure the network you use is 2.4GHz (WiFi 5GHz network is not supported) and that your signal is strong enough.
- Check your WiFi router settings. The encryption must be WPA2-PSK and protocol must be AES.
- If you cannot be connected with fast connection guide, follow the instructions for connection and try with manual search.
EXCLUSIVE DISTRIBUTOR
KALLIOPI KARYDA & CO LP
87A, 17th November str.
55535 Pylea, Thessaloniki, Greece
tel. +302316006600
fax +302316006650
www.morris.gr
Version 1.0 / Aug. 2020
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>