CREALITY Sermoon V1 3D Printer User Manual
- June 6, 2024
- Creality
Table of Contents
Sermoon V1 3D Printer
V1.0
To Our Dear Users
Thank you for choosing Creality. To make using our products easier, please
read this User Manual before you start and follow the instructions provided
carefully. Creality is always ready to provide you with high-quality services.
If you encounter any issues or have any questions when using our products,
please use the contact information at the end of this manual to contact us. To
further enhance your user experience, you can also use the following methods
to find out more about using our devices: SD card user manual: You can find
instructions and videos in the SD card provided with your device. You can also
log in to the Creality official website (www.creality.com) to find information
regarding software and hardware, contacts, device instructions, device
warranty information, and more.
Instructions for Use
1 Please do not use this device with methods and operations that have not been
described in this manual to avoid accidental personal injury and property
damage;
2 Do not place the device in flammable and explosive materials or near high
heat sources. Please place the device in a ventilated and cool environment
with little dust;
Do not place the printer in a vibrating or any other unstable environment. The
shaking of the machine will affect the printer’s printing quality;
4 It is recommended to use the filament recommended by the manufacturer to
avoid damaging the device;
5 Do not use the power cable of other products as a replacement during the
installation process. Please use the power cable provided with the machine.
The power plug needs to be plugged into a three-hole socket with a ground
wire;
6 To prevent moving parts from pulling the human body into the device and
cause cuts and lacerations, do not wear cotton gloves while operating the
printer;
7 To avoid burns caused by overheating of the platform, after printing, please
wait for the temperature of the HotBed platform to drop before removing the
model;
8 Please maintain the device often. When the device is unplugged, use a dry
cloth to clean the printer, clean up remnants in the filament box, and check
for foreign objects on the belt and endstop switch;
9 To avoid injuries, children under the age of 10 should not operate this
device without adult supervision;
10 Do not manually move the nozzle or the heating platform quickly, otherwise,
it may cause damage to the moving mechanisms or control circuit;
11 Users should abide by the laws and regulations of the corresponding country
and region where the equipment is located (place of use), abide by
professional ethics, and pay attention to safety obligations. The use of our
products or equipment for any illegal purpose is strictly prohibited. Our
company is not responsible for the relevant legal responsibilities of any
violators. 01
Table of Contents
1. Device Description
………………………………………………………………………………………………………………………………………………………………… 03-04 1.1 About
the device ……………………………………………………………………………………………………………………………………………………………………………..
1.2 List of tool kit items
…………………………………………………………………………………………………………………………………………………………………………. 1.3 Device
specifications ………………………………………………………………………………………………………………………………………………………………………
04-04
2. Instructions for Use
………………………………………………………………………………………………………………………………………………………………. 05-14 2.1
Unboxing instructions
……………………………………………………………………………………………………………………………………………………………………… 05-05 2.2
Local printing
…………………………………………………………………………………………………………………………………………………………………………. 07-11 2.3
Cloud printing via app
……………………………………………………………………………………………………………………………………………………………………… 12-15
3. Notes and Daily Maintenance
………………………………………………………………………………………………………………………………………………. 16-20 3.1 Changing
filaments …………………………………………………………………………………………………………………………………………………………………..
16-16 3.2 Lubrication maintenance
………………………………………………………………………………………………………………………………………………………………….. 17-17 3.3
Leveling the platform
……………………………………………………………………………………………………………………………………………………………………….. 17-18 3.4
Using and maintaining the magnetic adhesive sticker
………………………………………………………………………………………………………………………… 19-19 3.5 Cleaning foreign
objects from the chassis …………………………………………………………………………………………………………………………………………
19-19 3.6 Connecting to cloud print
………………………………………………………………………………………………………………………………………………………………… 20-20
012
Device Description 1.1 About the device
1
2
1.2 List of tool kit items
4 5
6 7
8
1. Cover 2. Front door
6. Display screen 7. Rack
3. SD card slot
8. Power switch
4. Filament entrance 9. Power socket
9
5. Ventilation fan
10. Voltage adjustment
10
port
Filament x1
Power cable x1
Wrench and screwdriver x1
Cutting plier x1
Nozzle x1
Leveling card x1
Nozzle cleaner x1
Card reader and SD card x1
Note: The components above are for references only. The actual product may vary.
grease x1 (For lubricating the bearings)
01
Glue stick x1 (Can be used directly on the printing platform to increase
adhesiveness and prevent models from wrapping)
M6 socket wrench x1
1.3 Device specifications
Model Modeling size Modeling technology Number of nozzles Nozzle diameter
Accuracy Print materials Supported slicing f ile formats Power rating HotBed
temperature Nozzle temperature Ambient temperature Power Loss Recovery
Filament detection Supported slicing software Printing methods Power
specifications Operating systems Printing speed Open door sensor Camera
Basic Parameters Sermoon V1 | Sermoon V1 Pro 175x175x165 mm FDM 1 0.4 mm
(Standard) ± 0.1 mm 1.75 mm PLA / ABS / PETG STL / OBJ / AMF 150W 80 250 10 –
30 Yes Yes Creality Slicer, Repetier-Host, Cura, Simplify3D Locally via SD
card or cloud printing via Wi-Fi 100-120Vac 200-240Vac 50/60Hz Windows XP /
Vista/ 7 / 10/ MAC / Linux 150 mm/s, normally between 30-60 mm/s Comes
standard with the Pro version Comes standard with the Pro version
014
2. Instructions for Use
2.1 Unboxing instructions
Notes
· Please ensure the correct position for the power supply switch and mains before supply connection, in order to avoid damage to the device. · If the mains between 100V and 120V, please select the 115V for the power supply switch. · If the mains between 200V and 240V, please select the 230V for the power supply switch (default is 230V).
A. Open the device’s cover.
B. Use the cutting plier to cut the cable ties around the nozzle.
C. Use the cutting plier to cut of f the cable ties on the X-axis and Y-axis belts, and remove the cut cable ties and foam.
D. Remove the foam from the inside of the device.
E. Check whether the moving mechanisms are moving smoothly.
015
230V
115V
F. Note: Please ensure that the voltage matches the power switch, otherwise the power supply may be damaged or burnt out.
Local printing
Cloud printing
Method 1 (Connect via Wi-Fi)
Insert SD card
Method 2 Connected
(Connect via Bluetooth)
to
network
Data
Server
3D / STL
Model slicing
G-code files
016
Install apps
1. Cloud slicer 2. Cloud print 3. Cloud monitor (Pro version)
2.2 Local printing 2.2.1 Install slicer
This manual only introduces the installation of Creality slicer software. If
users use other slicer software, we recommend to set the retraction parameter
to 3mm to avoid the risk of plugging.
1. Please login official Creality website (www.creality.com) to download the latest Creality Slicer software.
2. Select Preferences in sequence Configure Creality Next Select
corresponding language Next
Finish to complete the setting.
3. Select the current model.
4. Open Creality Slicer.
5. Load File 017
6. Select File
7. Generate G code Save to memory card
8. Insert Memory Card
It is important to note file name within the memory card must be in Latin letters or numbers. Chinese characters or any other special symbol cannot be display by the printer.
Note: For details on using the software, please refer to the slicing software user manual on the SD card.
018
2.2.2 Setup wizard When using the printer for the first time, please reset the
printer to zero. If this procedure fails, please turn off the power and
contact after-sales.
Note: The above interface is for reference only. The actual UI may vary.
1. No foreign objects on the printing platform
2. Return to zero self-test
45° 3. Install filament
4. Load filament
5. Insert SD card
019
2.2.3 Printing modes
225 225 100
69 70 70.68
225 225 100
69 70 70.68
1. PLA mode: As our company recommends the PLA mode, the system’s parameters have been set according to PLA filaments. It is recommended to use Creality filaments for printing. When the inside the box temperature exceeds 30°C, please open the top cover to avoid nozzle blockage.
225 225 100
69 70 70.68
225 225 100
69 70 70.68
2. ABS mode: As our company recommends the ABS mode, the system’s parameters
have been set according to ABS filaments. It is recommended to use Creality
filaments for printing. When printing, please ensure that the top cover is on
to keep the device’s temperature inside.
Note: When printing with ABS f ilaments, it is recommended that the size of a
single model be controlled within 100 x 100 mm (length x width) to avoid
warping caused by the characteristics of the filaments, which can result in
printing failure.
0110
Note: Please install the filaments as shown in the f igure above.
2.2.4 Start printing In this order, go to Print files Select file Print.
Note: The above interface is for reference only. The actual UI may vary.
225 225 100
69 70 70.68
225 225 100
69 70 70.68
225 225 100
69 70 70.68
225 225 100
69 70 70.68
2.2.5 Automatic open door check function (Pro version only) To prevent the accidental opening of the door and cause burns and mechanical injuries, please turn on the pause door opening function (this function is enabled by default).
225 225 100
69 70 70.68
225 225 100
69 70 70.68
011
2.3 Cloud printing via app 2.3.1 Install app
1. Scan the QR code to download the app
2. Download
3. Create account 0112
4. Log in
2.3.2 Connect to the network and cloud printing (Method 1: Connect via Wi-Fi)
As shown below, please use your smartphone to select your device model and
slicing:
Note: When cloud printing via the app, be sure to uncheck the PLA mode and ABS
mode on the device, otherwise the app cannot control the device temperature.
1. Add device
2. Scan the QR on the device
3. Network settings
4. Connect to device Wi-Fi
5. Connect to user Wi-Fi
6. New device added
7. Find model 01
8. Model slicing
9. Print via a network connection
2.3.3 Connect to the network and cloud printing (Method 2: Connect via
Bluetooth) As shown below, please use your smartphone to select your device
model and slicing:
Note: When cloud printing via the app, be sure to uncheck the PLA mode and ABS
mode on the device, otherwise the app cannot control the device temperature.
1. Add device
2. Search for Bluetooth device
(Turn on Bluetooth on your smartphone)
3. Add device
4. Select user Wi-Fi
5. Connect to user Wi-Fi
6. New device added
7. Find model 0114
8. Model slicing
9. Print via a network connection
2.3.4 Cloud monitor (Pro version only) Note: Open the camera interface on the
app, and both cloud printing and local printing can be viewed remotely using
the camera. The LED light will also automatically turn on in environments with
poor light.
Method 1:
Method 2:
1. Click
2. Real-time monitoring
1. Click
2. Real-time monitoring 1051
3. Notes and Daily Maintenance 3.1 Feed out and feed in f ilaments
Note: The above interface is for reference only. The actual UI may vary.
225 225 100
69 70 70.68
225 225 100
69 70 70.68
225 225 100
69 70 70.68
Once the specific temperature has been reached and filaments are withdrawing, please immediately pull out the filaments. Otherwise, the filaments may jam up once it has cooled down.
0116
3.2 Lubrication maintenance
Note: Please perform regular maintenance on the blue area using oil and
lubrication (as shown in the figure).
X-axis optical axis 1 X-axis optical axis 2
Y-axis optical axis 1
Y-axis optical axis 2
Spool
Z-axis optical axis 1
Z-axis optical axis 2
3.3 Leveling the platform
Note: After using the printer for a long time, the distance between the
platform and the nozzle may change, which could cause the adhesion of the
first layer of the model to become weak and cause a printing failure. Please
level the platform regularly.
222255 222525 101000
6699 7700 7700..6688
225 225 100
69 70 70.68
1071
You can use the leveling card provided to help with the leveling. The nozzle
should be just able to scratch the leveling card. Keep adjusting them until
you can feel a slight resistance from the nozzle when you pull the leveling
card.
Note: The nozzle is a damageable part. If the nozzle becomes heavily worn out,
please replace it regularly.
The nozzle is too far away from the platform, The filaments are evenly spread
out and The nozzle is too close to the platform, and the filaments and the
filaments cannot stick to the platform. are sticking to the platform just
right. are not extruded enough, which may damage the platform.
0118
3.4 Using and maintaining the magnetic adhesive sticker
Note: The printing platform is a damageable part. Please replace it regularly
to ensure the adhesion of the first layer model.
1. Take the printed model and platform out of the device together, and partially bend the platform slightly to separate the model from the platform. (The platform is not easy to bend to prevent the platform from deforming and becoming unusable)
2. The filament residue on the platform can be scraped off with a small household blade. Please pay attention to safety when using it.
3.5 Cleaning foreign objects from the chassis
3. If the adhesion of the first layer of the model is weak, please apply a glue stick evenly onto the surface of the platform.
1. Remove any foreign objects from the inside of the device.
Z-axis limit switch
2. Check whether there is any foreign object remaining on the Z-axis limit
switch to prevent the Z-axis limit switch from getting stuck. 1019
3.6 Connecting to cloud print
Note: If the network configuration is unsuccessful or you need to re-bind your
smartphone, please follow the steps below.
1. It is recommended to use the small wrench in the accessory package to
enter the rack’s reset hole and long-press the reset switch
for six seconds before releasing;
2. Once the Wi-Fi indicator light turns off, the system will automatically enable the yellow indicator light. When the yellow light starts flashing, that means reset has been completed;
3. Once the Wi-Fi has been successfully reset, use your smartphone to scan the QR code on the back of the device again to connect it to the network. You can also use a Bluetooth connection instead;
Long-press for six seconds
Yellow light starts flashing again
Connect via Wi-Fi or Bluetooth
0210
U.S. FCC Part 15 Regulatory Information: This equipment complies with
radiation exposure limits set forth for an uncontrolled environment. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. This equipment should be installed and operated with
minimum distance 20cm between the radiator& your body.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures: –Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver. –Connect the
equipment into an outlet on a circuit different from that to which the
receiver is connected. –Consult the dealer or an experienced radio/TV
technician for help.
Canada Regulatory Information : CAN ICES-3 (B)/NMB-3(B)
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions: (1) This device
may not cause interference. (2) This device must accept any interference,
including interference that may cause undesired operation of the device.
L’émetteur/récepteur exempt de licence contenu dans le présent appareil est
conforme aux CNR d’Innovation, Sciences et Développement économique Canada
applicables aux appareils radio exempts de licence. L’exploitation est
autorisée aux deux conditions suivantes : 1) L’appareil ne doit pas produire
de brouillage; 2) L’appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d’en compromettre le
fonctionnement.
Après examen de ce matériel aux conformité ou aux limites d’intensité de champ
RF, les utilisateurs peuvent sur l’exposition aux radiofréquences et la
conformité and compliance d’acquérir les informations correspondantes. La
distance minimale du corps à utiliser le dispositif est de 20cm.
For pluggable equipment, the socket-outlet shall be easily accessible. Pour
l’équipement pluggable, la prise de prise doit être facilement accessible.
Do not use this apparatus near water. Ne pas utiliser cet appareil à proximité
des sources d’eau.
Clean only with dry cloth. Nettoyer seulement avec un chiffon doux sec.
Only use attachment/accessories specified by the manufacturer. N’utiliser que
des accessoires recommandés par le fabricant.
Unplug this apparatus during lightning storms or when unused for long periods
of time. Débrancher l’appareil durant les orages ou lorsque non utilisé
pendant de longues périodes.
Refer all servicing to qualified service personnel. Servicing is required when
the apparatus has been damaged in any way, such as power-supply cord or plug
is damaged, liquid has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does not operate normally,
or has been dropped. Confier la réparation à du personnel technique qualifié.
Faire réparer lorsque l’appareil est endommagé; lorsque le cable oula fiche
d’alimentation est endommagé, lorsqu’on a renversé du liquide ou si des objets
sont tombés dans l’appareil, lorsque l’appareil a été exposé à de la pluie ou
à de l’humidité, si l’appareil ne fonctionne pas normalement, ou lorsqu’il est
tombé.
Internal/External Voltage Selectors : Internal or external voltage selector
switches, if any, should only be reset and re-equipped with a proper plug for
alternative voltage by a qualified service technician. Do not attempt to alter
this yourself. Sélecteurs de tension interne/externe : Les sélecteurs de
tension interne ou externe, s’il y en a, doivent être réinitialisés et équipés
avec une fiche adéquate par un technicien qualifié. Ne jamais tenter de
modifier ceci vous-même.
Protective earthing terminal : The apparatus should be connected to a mains
socket outlet with a protective earthing connection. Borne de terre de
protection : Par mesure de sécurité, l’appareil doit être branché à une prise
decourant comprenant une borne de mise à la terre.
When moving or not using the appliance, secure the power cord (e.g., wrap it
with a cable tie). Be careful not to damage the power cord. Before using it
again, make sure the power cord has not been damaged. If the power cord has
been damaged at all, bring the unit and cord to a qualified service technician
for repair or replacement as specified by the manufacturer. Veillez à toujours
fixer le cable d’alimentation lors du déplacement de l’appareil ou lorsqu’il
n’est pas utilisé.Veillez à ne pas endommager le cable d’alimentation.
Vérifiez toujours le cable d’alimentation avant d’utiliser l’appareil. Si
lecable d’alimentation est endommagé de quelconque façon, faites vérifier
l’appareil et le cable d’alimentation par un technicien qualifié recommandé
par le fabricant afin de les faire réparer ou replacer.
Disconnect power cord before servicing. Déconnectez l’appareil avant le
service.
Replace critical components. only with factory parts or recommended
equivalents. Remplacez les components seulement avec des components de la
fabrique ou avecdes équivalents recommandés.
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE ANY COVER. NO
USER- SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL
ONLY. CAUTION: POUR REDUIRE LE RISQUE DE CHOQUE ELECTRIQUE N’ELOIGNEZ PAS LA
COUVERTURE. PAS DE COMPONENTS UTILISABLES AU SERVICE A L’INTERIEUR. DEMANDEZ
SERVICE SEULEMENT AU PERSONNEL QUALIFIE.
EU Regulatory Information:
Support Frequency Bands and Power: WLAN /BT 2.4 GHz < 20 dBm;
The simplified EU declaration of conformity referred to in Article 10(9) shall
be provided as follows: Hereby, [Shenzhen Creality 3D Technology Co., Ltd.]
declares that the radio equipment type [Sermoon V1 Pro, Sermoon V1] is in
compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address:
https://www.creality.com/
Each model is different. All images are for illustrative purposes only, and the actual product may vary. The final interpretation right belongs to Shenzhen Creality 3D Technology Co., Ltd.
Official Website: www.creality.com
CM
5021078
R 210-170942
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>