Guangzhou Ezvalo Technology CSD01 Alarm Clock Speaker Dock User Manual
- June 6, 2024
- Guangzhou Ezvalo Technology
Table of Contents
Guangzhou Ezvalo Technology CSD01 Alarm Clock Speaker Dock
Parts
Buttons
-
Snooze Button
Short press: When the alarm keeps ringing, short press to turn on snooze mode, alarm will ring again 5mins later.
Long press: Turn off alarm clock. -
Display Brightness Adjustment
Short press: Display brightness adjustment 30% / 70% / 100%
Long press: turn on/off the night light -
FM/BT Switching
Single press to enter BT mode. The screen will show up BT and clock icon Double press to enter FM mode. The screen will show up FM icon
Triple short press to turn off BT and FM -
THUMBWHEEL SWITCH
A. BT mode:
Rotate left to select the previous song, rotate right to select the next song. Press to play/pause music.
B. FM mode:
Short scroll left/right: radio frequency +/- 0.1 Mhz
Long scroll left/right: Search radio channel
C. In clock adjustment mode:
Scroll left/right to set hour, and press to switch into minute setting. Press again to exit. -
Clock Setting
Clock setting: In normal mode, short press to start setting time. Rotate to adjust time, press to confirm time.
Exit setting mode: in clock setting mode, single press to exit
12h/24h switch: In any mode, long press to choose between 12-hour and 24-hour. -
Alarm Setting
-
Alarm clock setting: single press to enter alarm clock setting mode. Rotate to the left, and you can start to set time after the screen display “ON”. Press down to set Hour and minute. when the hour/minute on the screen flashes, rotate to the left/right to set time. After setting, press down to save settings. At the moment, the screen will show the normal time, and the alarm icon will be displayed on the screen.
-
Turn off the alarm setting: click , to select the alarm 1/alarm 2 that needs to be canceled, and adjust it to “OFF” by rotate to the right. At the same time,the display shows the selected alarm icon and the word“OFF”, indicating that the alarm has been canceled.
Gentle Reminder: When the alarm rings, press any button to activate snooze. It will ring again after 5 minutes, and the display will show (ZZZ). Hold SNOOZE button to turn off the alarm. -
Left Knob Button
Turn left FM/BT volume decreases
Turn right FM/BT volume increase
How to use
PRESS BUTTON FUNCTION
FM operation
-
Press twice to enter the FM radio mode. The default is 87.5MHz.
-
Search FM:
A. Scroll left/right to switch radio station.
B. Scroll left/right Long Press to search for a radio station. -
Save station: When you need to save radio station, long press until the word “PXX” flashes on the screen. And then rotate to select the storage location (P01,P02 or P03). After finishing setting, press down to save setting.
-
Play saved station : short press to display the position of the station that was played last time.
BT Link
Switch to the BT mode through the button. When you hear the notification tone,
the speaker is already turned on. When you see the BT indicator flashing, it
means that the speaker is searching for pairing. At this moment, you can turn
on the BT function of your phone, search for “EZVALO Cassini” and pair with
your phone. After successful pairing, the alert tone will ring again and the
indicator light will stop flashing.
If you need to reconnect to a new device, Long press force to trigger pairing
mode.
SPECIFICATIONS
Warnings
- DO NOT Expose to Liquids!
- DO NOT Disassemble!
- AVOID Dropping！
- AVOID Extreme Temperatures!
- DO NOT Charge Near the Magnetic Card!
- DO NOT Charge the Phone with a Metal Protective Case!
FCC statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
RF Exposure Information
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
Note: this equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 and part 18 of the FCC
Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and candidate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. During the operation of device a distance of 15 cm surrounding the device and 20 cm above the top surface of the device must be respected.
This device complies with Part 18 of the FCC Rules. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Increase the separation between the equipment and any other radio device.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
ISED Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply
with Innovation, Science and Economic Development Canada’s licence-exempt
RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
The digital apparatus complies with Canadian CAN ICES‐3 (B)/ NMB‐3(B).
EZVALO Customer Service
Email: service@ezvalo.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>