imin 121M01 Mobile POS User Manual
- June 6, 2024
- imin
Table of Contents
- imin 121M01 Mobile POS
- Minimal Setting
- How to Download I Use Apps
- List of Pre-lnstal led Apps and System Programs
- Introduction
- Installation Guide
- Charging Base Instructions (Optional)
- Name and Content of Toxic and Harmful Substances in This Product
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
imin 121M01 Mobile POS
Minimal Setting
You only need the followlng steps to open the device:
- 2G/3G setting, In the off state, Insert the corresponding 2G (GSM} / JG (GSM) card, and then turn it on.
- Press and hold the [Power] button for 2-3 seconds, light up the saeen, enter the first boot interface, and follow the prompts.
- Wi FI settings
- Ciiek the [Settings] button. then turn on the WLAN,enter the WLAN search intertace, wait for its search shows the available WlAN hotspots;
- Click on the WlAN that you would like to connect. If you choose an encrypted network, you need to enter the access code
How to Download I Use Apps
Launch App II cation Store under onllne mode to browse, dawn load and complete installation for relevantApps.
List of Pre-lnstal led Apps and System Programs
Public WI-Fl· OTA· Calculator· Settings· Music· Download
To learn more: Choose ‘Setup’-> ‘Application’ and select the the application
you wish to enquire about
To unload I uninstall a specific application: Choose ‘Setup’·> ‘Application’·>
‘Management Application’-> ‘Unloading’to uninstall application.
Altematively, long press on application icon and drag it to the trash can to
uninstall.
If you need more help, please find the Help-APP from the device.
Introduction
Power Button Press the power button to power on. Under pow,:r on
conditions, press and hold the button for 2-3 seconds to select power off or
reboot. In the standby status, press the control button for 8 sec. to power
off.
Display A touch screen for the operator.
Camera To scan the QR code and shoot
Type-C lntertace WlththecharglngfunctlOI\ for external devices, such as U
disk.
Pogo Pin Used to connect the charging base for charging (optional!.
Installation Guide
- 8open the battery cover;
- Insert the MicroSDCard,SIM Card as required;
- unscrew the printer cover and the paper compartment door pops open;
- insert the thermal paper and pull out part of it outside the paper exit of the printer, then close the paper compartment cover.
Charging Base Instructions (Optional)
- use a data cable to insert a Type-A Interface (OTG device) ora Type-C interface (for charging only), then press the wire into the Wire Slot:
- Put the host on the charging base correctly, after the successfully connected, turn on the power to start charging.
OS | Android 11 (Go edition) |
---|---|
CPU | 8-Core, 2 x A7S and 6 x ASS, 1.8GHz |
Screen
| 5.5 inches, resolution: 720 x 1280
Multi-touch capacitive screen
Storage| 2GB RAM+ 16GB ROM
Camera| 5.0M AF, with flash light
NFC| Optional
Wi-Fi| 2.4/5 GHz, Support 802.lla/b/g/n/ac
Bluetooth| 2.1/3.0/4.0/5.0, Support BLE
Card Slot| lx SIM
Network| 2G/3G/4G
GPS| GPS/Galileo/Glonass/Beidou
Printer
| 58mm thermal printer, support the paper roll
with maximum 40mm diameter
Speaker| 1.SW
External Interface
| 1 x USB Type-C port (OTGsupport)
1 x Earphone jack
TF Card| Support MicroSD (TF) up to 64GB
Battery| Changeable, 7.4V/2600mAh
Power Adapter| SV/2A
Machine Size| 206mm x 82mm x 62.8mm
Operating Temperature| o·cto+so·c
Operation Humidity| 10% to 90% r.H.
Storage Temperature| -2o·cto +60°c
Limit Altitude| Max. 5000 meters
Extended Support| Charging Base (optional)
Name and Content of Toxic and Harmful Substances in This Product
Part Name
| Toxic or harmful substances and elements
---|---
Plumbum Mercury Cadmium Chromium VII Polybrominated Polybrominated
biphenyl diphenyl ethers
Circuit Board|
Head of Printer| X 0 0
0: Means that the content of the toxic and harmful substances in all homogeneous materials of the component is below the limit specified in SJ/ tl13363-2006.
X: Means that the content of the toxic and hazardous substances at least in a homogenous material of the component exceeds the limit specified in SJ/ t113363-2006. However, the components marked with”X”in the above table are out of proportion because there is no mature alternative technology in the industry at present.