HOLLYLAND COSMO C1 Wireless Video Transmission System User Guide
- June 6, 2024
- HOLLYLAND
Table of Contents
COSMO C1
USER GUIDE
For the latest and detailed user guide, please download it from the official
website: www.hollyland-tech.com/support/Download
HOLLYVIEW
Powered by Hollyland
TYPICAL SETUP
Note: The
transmitter can be equipped with a mushroom antenna. When there is a large
height difference between the transmitter and receiver, it is recommended to
use a Hollyland mushroom antenna at the transmitter to improve the stability
of the wireless transmission.
PRODUCT INTERFACES
TRANSMITTER
Antenna Interface
HDMI Input
SDI Input
SDI Loop out
DC Power Input
Expansion Accessories Mounting Hole
LED Light (Yellow light indicates connection status, red light indicates low
power)
OLED Screen
Thumbwheel Switch
Power Switch
USB Type-C Interface
2I Outlet
1/4 Threaded hole| RECEIVER
Antenna Interface
HDMI Output
SDI Output1
SDI Output2
DC Power Input
Expansion Accessories Mounting Hole
LED Light (Yellow light indicates connection status, red light indicates low
power)
OLED Screen
Thumbwheel Switch
Power Switch
USB Type-C Interface
Outlet
1/4 Threaded Hole
---|---
INSTALLATION
INSTALLATION OF TRANSMITTER
- Install the antenna according to the angle shown in the picture.
- Install the magic arm onto the 1/4 threaded hole of the transmitter and install the assembled transmitter into the camera body.
- Install the battery (compatible with NP-F970 and others of the same series). ® Push the power switch to turn on the device.
INSTALLATION
INSTALLATION OF
RECEIVER
- Installs the antenna according to the angle shown in the picture.
- Install the receiver onto the stent through the 1/4 threaded hole on the bottom of the device.
- Install the battery (compatible with NP-F970 and others of the same series).
- Push the power switch to turn on the device.
OLED DISPLAY
- Signal Strength
- Indicator of Power Supply
- Video Format
- Channel Display
- Indicator of Auto-frequency-hopping
NOTE
The “AUTO” indicates that the frequency point is in the automatic frequency
hopping mode (the picture on the right); switching the frequency manually will
change the device to the locked-frequency-mode state in the left picture.
QUICK GUIDE
ENTER MENU
Long press the thumbwheel switch for three seconds to enter the menu. Flip the
toggle wheel up or down to switch menu options, and click to confirm.
CHANNEL SWITCHING
Toggle up/down the switcher to change the menu options on the transmitter or
receiver, click the confirm key to confirm the channel, then the receiver and
the transmitter channel will be synchronized automatically.
SUPPORT
If encounter any problems in using the product or need any help, please
follow these ways to get more technical support:
Hollyland Products User Group
HollylandTech
HollylandTech
support@hollyland-tech.com
www.hollyland-tech.com
FCC REQUIREMENT
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment. This
device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: this device may not cause harmful interference, and
C) this device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy, and if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected
— Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body. This transmitter
must not be co-located or operating in conjunction with any other antenna or
transmitter. t any interference received, including interference that may
cause undesired operation.
Hollyland Products User Group
HollylandTech
HollylandTech
support@hollyland-tech.com
www.hollyland-tech.com
SHENZHEN HOLLYLAND TECHNOLOGY CO,. LTD
8F, 50 Building, Skyworth Innovation Valley, Tangtou, Shiyan, Baoan District
Shenzhen, China.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>