Third Reality 3RWCC021U Vehicle-Mounted-Wireless Charging Kit User Guide
- June 6, 2024
- THIRD REALITY
Table of Contents
3RWCC021U Vehicle-Mounted-Wireless Charging Kit
What’s in the Box
- Wireless Charger X 1
- Car Accessories Car Adapter for fast charger Xl Car Clip X l
- User Manual X 1
Product Introduction
This is an automatic induction Wireless Charger that support Qi and magnetic
attachment wireless charging agreement, let you enjoy the fun of wireless
products easily.
This Wireless Charger can directly connect with device, with included power
adapter it provides a fast charging for your smartphone. Super easy to setup,
just put it on the device and then plug it into the type-c outport of the
device.
You can voice control the device to come to you, and then let the it takes
your smartphone to charge.
This is a Dual-Mode Support Wireless Charger. It not only can work with the
device, but also can be used in the car with included Air
Clip and Car Adapter.
LED Indicating
Power Connected: LED flicker 3 times per seconds
Charging: LED is always lighting
Charging full: LED go out
Note: When put on a mobile phone which not support wire less charging, the
LED will flicker till the phone move off.
Specification
Input: DC5V=3A
Output: 15W (MAX)
Note: All Devices must be Ql-enabled; Recommend QC2.0 or the included charging
Adapter to achieve the effect of wireless fast charging; The back of the phone
shall not be equipped with metal plates, otherwise, it will affect or even
damage the wireless charging equipment and phone.
Product Configuration
Use with the device
-
Take out the Wireless Charger, insert the USB-C port into the output port of the device.
-
Tear off the protective paper from the suction cup on the base.
-
lnsta ll the Wire less Charger on the device.
-
Adjust the angle and position according to your personal preference. Use in the car
L Remove the USB-A port from the Power Adapter and then insert it into the Car Adapter. -
Tear off the protective paper from the suction cup on the base.
-
Install the Wire less Charger on the car. Optional: There is an Air Clip included in the package, you can use it instead of the original holder.
Note:This charging pad is controlled by smart clips, which allows long-term standby.
Notes:
- Do not squeeze or collide.
- Do not disassemble or throw into fire or water, to avoid causing a short circuit leakage.
- Do not use wireless charger in severely hot. humid or corrosive environments, to avoid circuit damage and the leakage phenomenon.
- Do not place too close with magnetic stripe or chip card (ID card, bank card, etc.) to avoid magnetic failure.
- Please keep the distance at least 20cm between implantable medical devices (pacemakers. implantable cochlear, etc.} and the wireless charger, to avoid potential interference with the medical device.
- To take care of the children, to ensure that they won’t play the wireless charger as a toy, to avoid unnecessary accidents.
- Please keep the charger away from water or other liquid.
- If you need to clean the charger, please make sure it is not connected power supply.
- Using Environment temperature remains 0- 45°C.
The involved images are sketch maps, end-products subject to the object entity.
FCC Regulatory Conformance:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference
- This device must accept any interference received, including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
NOTE: This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consu It the dealer or an experienced radio/TV technician for help.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.
Limited Warranty
For limited warranty, please visit www.3reality.com/devicesupport
For customer support, please contact us at i nfo@3rea lity or visit
www.3reality. com
Warning Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept
any interference received, including interference that may cause undesired
operation. Any Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates uses and can radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Read More About This Manual & Download PDF:
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>