Acsip AI50H EVK User Guide

June 6, 2024
Acsip

AI50H EVK
User Guide
AcSiP Technology Corp.
www.acsip.com.tw

A150H EVK Connector Description

Module peripheral Circuit Diagram

USB to UART Circuit Diagram

Power Supply Circuit Diagram

Antenna Specifications

RFA-WAVE-055-U-B70-1
Specifications

Frequency 865-928 MHz
Peak gain 2.0 dBi
Average gain 0.6 dBi
VSWR 3.0 : 1 Max.
Polarization Linear. vertical
Impedance 500
Connector RP SMA PLUG

Environment & Mechanical Characteristics

Temperature – 10°C to -55’C
Humidity 95% @ 25’C
SPEC NO. SP-12G0228GT01-04 ISSUE DATE 2017.03.06 P1131ISHED RV
PRODUCT NAME . OMA-G01 VERSION VO4
PAGE 3/10
(OMM Fiberglass Antenna)

Product Description

The Linehan-TECH 8 dBi Fiberglass omnidirectional antenna is specially designed for applications operating in 902-928 MHz frequency, including radio frequency identification (RFID), land mobile, location monitoring systems (LMS), and ISM applications. It features high gain and is vertically polarized. Includes a heavy-duty mounting bracket and an N-style Jack connector.

Model


Frequency Range

|

902 – 928 MHz

Bandwidth

| 26 MHz
Gain|

8 d Bi

Horizontal Beamwidth

| 360°
Vertical Beamwidth|

16°

VSWR

| 52.
Nominal Impedance|

SO Ohms

Maximum Power rating

| 100 Watts
Polarization|

Vertical

Connector

| N-Style Jack
Lenth|

51.6′ / 131cm

Wind Load

| 120 mph
Radome|

White Fiberglass

Mast Mount Diameter

| 01.5″ – 02.0″
Operating Temperature Range|

-22°F – 158°F

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

IMPORTANT NOTE:
FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.
This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/CANA.

Integration instructions for host product manufacturers Applicable FCC rules to module
FCC Part 15.247
Summarize the specific operational use conditions
The module is must be installed in mobile device.
This device is intended only for OEM integrators under the following conditions:

  1. The antenna must be installed such that 20 cm is maintained between the antenna and users, and
  2. The transmitter module may not be co-located with any other transmitter or antenna As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed.

IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end-user manual shall include all required regulatory information/warning as shown in this manual.

Limited module procedures Not applicable
Trace antenna designs Not applicable

RF exposure considerations
20 cm separation distance and co-located issue shall be met as mentioned in “Summarize the specific operational use conditions”. Product manufacturer shall provide below text in the end-product manual “This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body.”

Antennas

Brand name| Model name| Antenna type| Antenna gain| Antenna connector
---|---|---|---|---
Aristotle| RFA-WAVE-055-U-B70-1| Dipole| 2 dBi| R-SMA
lian than tech corp.| OMA-G01| Dipole| 8 dBI| N-type

Label and Compliance Information
Product manufacturers need to provide a physical or e-label stating Contains FCC ID: 2ADWC-AI5OH” with the finished product

Information on Test Modes and Additional Testing Requirements
Test tool: termite-3.3 shall be used to set the module to transmit continuously.

Additional Testing, Part 15 Subpart B Disclaimer
The module is only FCC authorized for the specific rule parts listed on the grant, and the host product manufacturer is responsible for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. The final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed

Professional installation instruction
Please be advised that due to the unique function supplied by this product, the device is intended for use with our interactive entertainment software and licensed third-party only. The product will be distributed through a controlled distribution channel and installed by trained professionals and will not be sold directly to the general public through retail stores.

  1. Installation personal
    This product is designed for specific applications and needs to be installed by a qualified person who has RF and related rule knowledge. The general user shall not attempt to install or change the setting.

  2. Installation location
    The product shall be installed at a location where the radiating antenna can be kept 20cm from a nearby person in normal operating condition to meet regulatory RF exposure requirements.

  3. External antenna
    Use only the antennas which have been approved by the applicant. The non- approved antenna(s) may produce unwanted spurious or excessive RF transmitting power which may lead to the violation of the FCC/IC limit and is prohibited.

  4. Installation procedure
    Please refer to the user’s manual for the detail.

  5. Warning Please
    carefully select the installation position and make sure that the final output power does not exceed the limit set force in relevant rules. The violation of the rule could lead to serious federal penalties.

AcS1P Technology Corp.
www.acsip.com.tw

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals