PCNA 7197-64 Clip Clap 2 Bluetooth Speaker Instruction Manual
- June 12, 2024
- PCNA
Table of Contents
PCNA 7197-64 Clip Clap 2 Bluetooth Speaker
Product Information
- Model: 7197-64
- Functions:
- Clip
- ON/OFF Switch
- LED Indicator
- Type-C USB Port
- FCC Compliance: This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
- Safety Precautions:
- Read all the instructions before use.
- Never store or use this product in moisture.
- Do not use the device in excess of its output rating.
- Close supervision is required when the product is used near children.
- Do not use the device if it has been disassembled, as it may cause explosion or risk of injury.
- Do not disassemble the device. For any repairs, consult a professional.
- RF Exposure Information: The device was evaluated to meet general RF exposure requirements. This equipment should be installed and used with a minimum distance of 0 mm between the radiator and your body.
- Country of Origin: China
Product Usage Instructions
- Before initial use, fully charge the speaker.
- For optimal battery performance, it is recommended to complete 2 or 3 charge and discharge cycles.
- Ensure proper supervision when using the product near children to reduce the risk of injury.
- Avoid exposing the device to moisture.
- Do not exceed the device’s output rating to prevent damage.
- Never use the device if it has been disassembled, as it may cause explosion or risk of injury.
- Do not attempt to disassemble the device. For any repairs, seek assistance from a professional.
- When pairing with a mobile device, the speaker will automatically pair if the mobile device has been paired before.
Instruction Manual
Functions
- Clip
- ON/OFF Switch
- LED Indicator
- Type-C USB Port
What’s included
- 1 x Bluetooth® Speaker (7197-64)
- 1 x USB to Type-C Charging Cable
- 1 x Instruction Manual
Tech Specifications
- Battery Capacity: 3.7V, 1.11Wh, 300mAh
- Playback time: 1.5 hours at max volume
- Charging time: up to 1.5 hours
- Pairing name: “Clip Clap 2”
- Bluetooth version: 5.0
- Speaker driver size: Ф13X12.5MM
- Rated output power: 2W
- Range: 10M
- Impedance:4 Ω
- Frequency response:150 Hz ~ 15 K Hz
- Signal noise ratio: 75db±3
- Input voltage: DC5V 250mA
Instructions
(Be sure to fully charge the speaker before using for the first time).
- Charging the Speaker:
- Connect the provided charging cable to a power source and to the Type-C USB port on the speaker (4).
- The LED indicator light will glow red when charging and turn off when fully charged.
- Bluetooth® Setup:
- Press and hold ON/OFF button to turn on the speaker, LED Indicator will flash RED&BLUE when in pairing mode.
- Turn ON the Bluetooth function on mobile device, select “Clip Clap 2” pairing name.
- If the devices have successfully paired, the LED will slowly flash BLUE. The speaker will automatically pair if the mobile device has been paired before.
- When the bluetooth is disconnected, the speaker will automatically shut-off after 3 mins.
- Press and hold the ON/OFF button to turn OFF the speaker.
- Play and Calling Controls:
- When playing music, short press ON/OFF button to pause/resume music.
- When there’s an incoming call, short press ON/OFF button answer the call and press again to end the call
- Press and hold the button to reject the call.
SAFETY PRECAUTIONS
WARNING : When using this product, basic precautions should always be followed:
- Read all the instructions before use.
- Never store or use this product in temperatures below 32°F (0°C) or above 115°F (45°C).
- The unit will only achieve full performance after 2 or 3 completed charge and discharge cycles.
- To reduce the risk of injury, close Supervision is required when the product is used near children.
- Do not expose the device to moisture.
- Do not use the device in excess of its output rating.
- Overloaded outputs above the rating may result in a risk of fire or injury.
- Do not use the device if it has been damaged or modified
- Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
- Do not disassemble the device. For repairs, seek a qualified service professional. Incorrect reassembly may result in a risk of fire or injury.
- Do not expose the device to fire or excessive temperatures. Exposure to fire or temperatures above104°F (40°C) may cause an explosion.
- To ensure product safety, make certain that a qualified service professional uses only identical replacement parts
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RF Exposure Information
The device was evaluated to meet general RF exposure requirements. This
equipment should be installed and used with a minimum distance of 0 mm between
the radiator and your body.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference,
- This device must accept any interference received, including interference that may cause undesired operation.
Warning : Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>