JLB7tech LB55855T Baby Monitor Instruction Manual
- June 6, 2024
- JLB7tech
Table of Contents
LB55855T
INSTRUCTION MANUAL
Setup and use your digital video baby monitors
Installing Baby Unit
A. Place the Baby Unit on a flat surface, such as a desk or shelf, or
mount the camera on a wall.
B.
Connect the small plug of the power adapter to the Baby Unit and the other end
to a suitable electrical outlet. Only use the enclosed adapter (5V DC 1000mA).
The baby unit is turned on and the power LED will be green.
WARNING
THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT SUPERVISION
- When an AC Adapter is plugged into an electrical outlet, do not the exposed end.
- Test baby monitor before first use, periodically, and when changing location of the baby unit(Camera).
- Do not use a monitor near water (Such as bathtub, Sink, etc).
- Keep parent unit away from heat sources (Such as stoves, radiators, etc).
- Make sure there is proper ventilation around the baby unit and parent unit.
- This product is not a toy. Do not allow children to play with it.
- The mains plug or an appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
- The baby monitor should not be considered as a medical device. While using the baby monitor, it is strongly recommended to have an adult directly check on your baby. Premature babies or children considered at risk must be supervised by your pediatrician or other medical staff.
WARNING AC Adapters provided.
STRANGULATION HAZARD-Children have STRANGLED in cords. Keep this cord out of
reach of children (more than 3 feet/1 meter away from the crib). Never use
extension cords with AC adapters. Only use the
C. Connecting the power supply for the Parent Unit. Connect the small
plug of the power adapter to the base bracket or the parent unit and the other
end to an electrical outlet. Only use the enclosed adapter (5V DC/2000mA).
Recommend charging time of at least 3 hours before first use.
Precaution: use of battery for Parent Unit
Only charge the battery when the battery life indicator is low. Constant
recharging of your battery before the low battery indicator light comes on
will decrease the life of your batteries.
When the battery is low, the power on-off LED (icon) will flash red and the
on-screen display battery icon will flash red indicating that the battery
needs to be charged.
Function of keys and LED indicators
Parent Unit
Battery Warning
- Use only the original rechargeable battery provided.
- Do not shoot-circuit supply terminals.
- Remove the battery when the product is stored for long periods of time or when the battery is exhausted.
- Dispose of exhausted battery properly.
- Keep all batteries away from children.
- The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
- The danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type.
- Batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire, or the like.
WARNING Adult assembly is required. Keep small parts away from children
when assembling.| Warning Information
- Keep this instruction manual for future reference.
- For adult use only.
---|---
| Talk| Press and hold to talk to the baby unit.
---|---|---
OK/CAM| Select| Menu mode (Press to select menu option)
vox| Power Saving-on/off| Press to switch on/off Power Saving (When the
power-saving mode is enabled, the screen will be turned off)
▲▼| Up/Down
Camera Up/Down
| Menu mode (Press to adjust menu settings) View camera mode(Press to control the current camera to rotate up/down)
◀ ▶
| Left/Right
Camera Left/Right
| Menu mode (Press to adjust menu settings) View camera mode(Press to control the current camera to rotate left/right)
Precautions
- Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electrics
- The baby monitor works better in temperatures ranging between 0 C and 40 r: (32 F and 104 T
- Do not dismantle the It does not contain any parts that may be used independently. Never expose the baby monitor for long period to the sun’s direct rays and never place it next to a source of heat, in a damp or very dusty room.
- Never push objects of any kind into this product through openings they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
- Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other Refer all servicing to qualified service personnel.
The product should be mounted to a wall or ceiling only as recommended by the manufacturer
PAIR| Pairing button| When the camera is powered on, press it the power LED
starts to blink, the camera is in pairing mode, and press it again to exit
pairing mode.
---|---|---
This device complies with Part 1S of the Rules. FCC operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
FCC Caution
To assure continued compliance, any changes or modifications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate this equipment (Example -use only shielded interface
cables when connecting to computer or peripheral devices).
This equipment complies with FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20 centimeters between the radiator and your body.
FCC Radiation Exposure Statement
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
The antennas used for this transmitter must be installed to provide a
separation distance of at least 20cm from all persons and must not be co-
located or operating in conjunction with any other antenna or transmitter.
JLB7Tech’s baby monitor warranty policy JLB7Tech will repair or replace (at our option)your unit free of charge for 12 months from the date of purchase if the unit is defective in workmanship or materials. To claim your repair/replacement, the product must be returned to J LB7Tech together with a copy of the purchase receipt In the absence of the purchase receipt the warranty will be 12 months from the date of manufacture. This warranty does not apply to normal wear or damage from misuse. abuse, improper, and handling. installation, accident. unauthorized repair or alteration. Please contact our Customer service by Facebook JLB7Tech or via email for details.
Start to use the monitor
Status bar
Menu operation
| Feeding time reminder is activated
---|---
| Baby room temperature
| Talk function is activated
| Signal strength reference
| Scan view is activated
| Camera number
``| System time
| Screen off is activated
| Zoom in is activated
| Temperature alert is activated
| Monitor is muted
| Battery level
| Adjust Parent Unit LCD Brightness lighter or darker.
| Power saving mode: To activate the Parent unit from the Power saving
mode.
| Turn off the screen and leave audio on: Keep audio continuously on when
the screen is off in power-saving mode..
| ECO mode: Turn off both video and audio to save more battery energy.
When the camera detects sound, the monitor automatically activates. Three
detection sound levels can be set
| Quiet: Baby cries a little bit to activate the Parent Unit.
| Medium: Baby cry moderate to activate the Parent Unit.
| Loud: Baby cries louder to activate the Parent Unit.
| ADD: Add an additional camera. Four cameras can be added. Step 1: Move
the parent unit to the same area as the camera. Both parent and baby units are
switched on. Step 2: Select camera number in Add camera Menu. Press “OK” to
begin pairing. Step 3: Within 50 seconds, press the “Pairing button” on the
camera to pair, the camera light will be flashing
Industry Canada Statement
This device complies with the Industry Canada licence-exempt RSS standard.
Operation is subject to the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any interference,
including interference that may cause undesired operation of the device.
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limit set forth for
an uncontrolled environment. This equipment should be installed and operated
with a minimum distance of 20cm between the radiator and our body.
Delete camera : Delete paired camera from the added camera list.
SCAN: Display paired cameras one by one.
OffOff: Deactivate the loop display function of paired cameras.
Cycle time setting, 10s, 15s, the 30s can be set.
Zoom
Adjust camera volume: Sound level from Ito 5.
Camera volume will be adjust the lullaby sound.
C: Display temperature in Celsius scale.
F: Display temperature in Fahrenheit scale.
Time setting: Set the monitor system time.
Feeding time alert setting.
Three different feeding time points can be set.
OFF: Deactivate feeding time alarm function.
On: Activate feeding time alarm function. When the feeding reminder alarm
is set, after the time is up, even the parent unit is in VOX mode, beeps sound
on the parent unit , the message “Feeding Time” is displayed on the screen.
Press any key to cancel the reminder.
Activate or deactivate lullaby function, 5 lullabies can be chosen. When turn
on lullaby, on Baby Unit side will always hear the ringtone from Parent Unit.
OFF: Deactivate lullaby function. Repeat: Repeat all lullabies.
High: Beep Alarm is issued when room temperature is higher than this
setting.
Low: Beep Alarm is issued when room temperature is lower than this
setting.
ON: Activate room temperature alarm function.
Explanation On/Off: We try to explain status and function of the menu.
You can turn the explanation on or off based on your usage.
Reset: Choose whether to restore the monitor to factory default settings.
All paired cameras will be removed from the paired camera list.
Language: To change the laguage of the parent unit menu display.
Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communicaotions.
However, there is no guarantee that interference will not occur in a
particular installation.lf this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on.the user is encouraged to try to correct the interference
by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.