Han Networks AP301 HAN Access Point Installation Guide

June 6, 2024
Han Networks

Han-Networks

Han Networks AP301 HAN Access Point

Summary of Installation Steps

  • WLAN Planning. Usually, a comprehensive site survey is required before installation, such as installation location, brackets, cables, power source, etc.
  • Unpack the AP box and check all contents
  • Install the AP bracket on ceiling or wall
  • Installing the AP
  • Connecting required cables
  • Power connection
  • Verifying post-installation connectivity
  • AP provisioning

Access points are radio transmission devices and are subject to governmental regulation. Network administrators who are responsible for the configuration and operation of access points must comply with local broadcast regulations. Specifically, access point must use channel assignments appropriate to the location where the access point will be deployed.

Package Contents

Item Name Qty Unit
1 Access Point 1 Pcs


2

| Quick Start Guide| 1| Pcs
Installation Guide| 1| Pcs
Regulatory Compliance and Safety Information| 1| Pcs
User Guide Info Card| 1| Pcs

Optional Accessories(To be ordered separately)

Item Name Description
1 AP-MNT-B Indoor mounting kit, Type B1(9/16″) and

B2(15/16″) for T shaped ceiling rail.


2

| ****

AP-MNT-C

| Indoor mounting kit, Type C1(Open

Silhouette) and C2 (Flanged Interlude), for other shaped ceiling rail mounting.

3| AP-MNT-W| Indoor mounting kit, Type W wall and ceiling mounting with screws.

Figure1: Product PackingCaptureHan-Networks-HAN-Access-
Point-1

Inform your HAN sales representative of incorrect, missing, or damaged parts. If possible, retain the carton, including the original packing materials. Use these materials to repack and return the unit to the supplier if needed. Additional mounting
kits for use with the HAN Access Points are sold separately. Contact your HAN sales representative for details.

Hardware Overview

The following sections outline the hardware components of the AP301 Series access point.

Figure 2: AP301 Front ViewCaptureHan-Networks-HAN-Access-
Point-2

LED

The AP301 Series access point is equipped with hidden LED display that indicates different status with different color.
For the details of the LED status, please refer to the Quick Start Guide.

Figure 3: AP301 Back View

AP301 series External Interfaces

Interface Specifications
1 Gigabit Eth0 1x 10/100/1000BASE-T autosensing (RJ-45) port, Power over

Ethernet (PoE,55V,450mA). In case of only one WAN

link,Eth0 would be preferred.


1 Gigabit Eht1

| 1x 10/100/1000BASE-T autosensing (RJ-45) port, Power over Ethernet (PoE,55V,450mA). In case of only one WAN link,either of Eth0 and Eth1 could work as WAN, Eth0 would be more preferred. In case of two WAN links,

Eth0 + Eth1 would be preferred.

Console| RJ-45 female connector, default is RS-232 Console for Service & Support only.
USB| USB 2.0 host interface (Type C, output DC 5V,0.5A )
DC Power Socket| DC 48V,500mA, power jack, support powering AP through a designated AC-DC power adapter.


Reset

| Factory reset. Press reset button for 5s, AP LEDs will quickly flash for 3s, then AP will restart and restore

factory configurations.

Security

Lock Slot

| The AP is equipped with a security lock slot for

additional security.

Table 2 Ethernet Port Pinout

Table 3 Console Port Pinout Table 4 RS-485 Port Pinout

Note: The serial console port allows you to connect the AP to a serial terminal or a laptop for direct local management. This port is an RJ-45 female connector with the pinouts described in Table 3. Currently for use by Service & Support only.
Note: The RS-485 port allows you to connect the AP to a RS-485 terminal. The maximum allowable current of PSE 12V power output is 300mA. In addition, PSE 12V power output can be turned on and off by software. This port is an RJ-45 female connector with the pinouts described in Table 4.

Power

The AP301 series access point supports direct DC power adapter (48V DC nominal, sold separately) and Power over Ethernet (PoE).
The DC power connector port is located on the back of the device, as shown in Figure 3. The PoE allows the Ethernet port to draw power from an IEEE 802.3at compliant source.
HAN Access Point supports the power adapter provided by HAN ONLY.

Before You Begin

Refer to the sections below before beginning the installation process.

Pre-installation Checklist
Before installing your AP301 Stellar access point, be sure that you have the following items:

  • 8-conductor, CAT5 or better UTP cable of required length.
  • One of the following power sources:
    • IEEE 802.3at compliant Power over Ethernet (PoE) source (PoE switch or PoE injector).
    • AC-DC adapter (sold separately),output voltage DC 48V, output current ≥0.6A
  • A terminal or a notebook

Identifying Specific Installation Locations
You can mount the HAN Access Points on a ceiling rail or on a wall. You should first determine the location of the installation. The installation position is located at the center of the required coverage area and should be free from obstructions or obvious sources of interference.

  • Minimize the number of obstructions (such as walls) between the AP and user terminals.
  • Electronic equipment or devices (such as microwave ovens) which may produce radio frequency noise should be away from the installation position of the AP.

It is strictly prohibited to install around stagnant water, water seepage, leakage or condensation. Avoid cable condensation or water seepage along the cables connecting to the AP.

AP Installation

Refer to mounting kits installation Guide.

Verifying Post-Installation Connectivity
The LED on the AP can be used to verify that the AP is receiving power and initializing successfully.

Product Specifications

AP301 series Dimensions/Weight

Unboxed AP301:

  • Net Weight: 1.64lbs / 0.74kg
  • Dimensions (HxWxD): 7.1 inches x 7.1 inches x 1.42 inches (18 cm x 18cm x 3.6cm)

Environmental

  • Operating :
    • Temperature: 0°C to +50°C (+32°F to +122°F)
    • Humidity: 10% to 90% non-condensing
  • Storage and transportation :
    • Temperature: -40°C to +70°C(-40°F to +158°F)

For additional specifications on this product, please refer to the Datasheet.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals