GE Appliances CFIXCNLR4S1 Cync Fixture Canless Installation Guide
- June 6, 2024
- GE Appliances
Table of Contents
Installation Guide
Cync Fixture
Canless
www.gelighting.com
The GE brand and logo are trademarks of the General Electric Company. ©2020 GE
Lighting. Information provided is subject to change without notice. All values
are design or typical values when measured under laboratory conditions.
PRODUCT COVERED
Model| Input voltage
(Vac, Hz)| Current
(mA)| Wattage
(W)
---|---|---|---
CFIXCNLR4S1| 120, 60| 110| 13
CFIXCNLR6S1| 120, 60| 130| 16
CFIXCNLR4C1| 120, 60| 110| 13
CFIXCNLR6C1| 120, 60| 130| 16
DIMMING
Compatible with Cync 3-wire smart switch. Do not compatible with a regular dimmer. Download Cync App for dimming and other controls.
BEFORE YOU BEGIN
Read these instructions completely and carefully.
WARNING
- Risk of fire or electric shock. Installation requires knowledge of luminaire electrical systems. If not qualified, do not attempt installation. Contact a qualified electrician.
- To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or other sharp objects.
- This device is not intended for use with emergency exits.
PREPARE ELECTRICAL WARNING
Electrical Requirements
The LED fixture must be supplied with 120VAC 60Hz.
Grounding Instructions
The grounding and bonding of the overall system shall be done in accordance
with National Electric Code(NEC) Article 600 and local codes.
Note: This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:(1) This device may not cause harmful
interference; (2) this device must accept any interference received, including
interference that may cause undesired operation.
Risk of Damage: Must use UL-approved conduit fittings for all enclosure
box connections to prevent wire cuts by sharp edges and excessive strain on
wiring.
INSTALLATION
- Turn off power source at the main circuit breaker or fuse box.
- Drill holes in the ceiling and prepare supply wire. Hole size CFIXCNLR4S1/ CFIXCNLR4C1 4 ¼ inch, CFIXCNLR6S1/ CFIXCNLR6C1 6 ¼ inch.
- Bring the supply power to the junction box through knockout and secure with strain relief. Use the wire nuts to connect power supply wires to respective color wires in the junction box.
- Place the junction box on the ceiling through a cur hole. Connect the light with the junction box with the connector.
- Hold the spring clips against the fixture and gently guide them into the ceiling until the clips snap into place.
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. The grantee is not
responsible for any changes or modifications not expressly approved by the
party responsible for compliance. Such modifications could void the user’s
authority to operate the equipment. This equipment has been tested and found
to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna
. – Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body.
This device contains license-exempt transmitter(receiver(s) that comply with Innovation. Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions
- This device may not cause interference
- This device must accept any interference. including interference that may cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>