NEW BRIGHT 050211108941 1:10 Radio Controlled Truck Owner’s Manual

: June 6, 2024
: NEW BRIGHT

Table of Contents

Proper Use Precautions and Care
Component Checklist
Vehicle Features and Functions
Transmitter Charging the Battery
Battery Installation
Trouble Shooting & Support
FCC CAUTION
Warranty
Customer Support
Read User Manual Online (PDF format)
Download This Manual (PDF format)

NEW BRIGHT 050211108941 1:10 Radio Controlled Truck Owner’s Manual

Proper Use Precautions and Care

Precautions

Component Checklist

(1) R/C Vehicle With USB Cord
(1) Transmitter
(2) AA Batteries

Vehicle Features and Functions

Installation Instructions

The ON/OFF Switch controls the main power to the vehicle, To save battery life, always remember to put switch in the OFF position when not in use.

The 4 Wheel Drive Flexible Chassis gives the vehicle the ability to climb steep angles. Each wheel has independent suspension during forward and reverse drive. The vehicle also has elongated shocks and soft tires that help grip the ground.

Steering Trim Dial is found in between front wheels on the top side of the chassis, under the vehicle body. If vehicle pulls to the left or right during forward driving the Steering Trim may need to be adjusted.

Features and Functions

This transmitter is equipped with 2.4GHz technology which allows up to 6 vehicles to be raced at the same time.

The transmitter will automatically sync with the vehicle.

Transmitter Charging the Battery

This vehicle is equipped with an internal Lithium-Ion battery that is recharged via USB. ON/OEF Switch must be in the OFF position prior to charging.
Installation Instructions

Locate the ON/OFF switch and USB cord on the under-side of the vehicle.
Turn the ON/OFF switch to the “OFF position.
Slide open Storage Compartment cover.
Remove USB cable from the Storage Compartment. (Use care when extending cord as it is attached to inside internal battery). Cord can be plugged into any computer or USB outlet brick (not included).
While charging, the LED under the vehicle will be on. Once fully charged the LED will turn off. Charging is completed in approximately 1 hours. Return cord and secure storage lid before operating the vehicle.

Battery Installation

Remove the screw to open the Battery Compartment Cover.
Insert 2 “AA” size batteries. Make sure the positive (+) and negative (—) markings on the batteries match up to the ones inside the Battery Compartment.
Replace the Battery Compartment Cover and replace the screw.

Note: When replacing Transmitter batteries: Do not mix old and new batteries. Do not mix alkaline, standard or rechargeable batteries. Use alkaline batteries only.

Trouble Shooting & Support

Problem -Vehicle does not move or moves slowly.

Make certain there are fresh batteries in the transmitter and that they have been installed in the correct position.
Are the (+) and (—) markings on the batteries in the same position as the (+) and (—) markings in the Transmitter Battery Compartment?
Are the metal contact tabs touching, rusty or dirty in the transmitter?
Has the vehicle been fully charged?
Make certain that the vehicle ON/OFF switch is in the “ON” position.

Problem- Vehicle moves by itself or exhibits reduced range from the transmitter.

Make certain there are no outside radio interference in your area. The best way to test this is to take the vehicle as far away from radio towers, electrical lines or tall buildings as possible to ensure no further radio interference will occur.
Always remove Batteries from transmitter when not in use.
Do not dispose batteries in fire. Leakage, explosion and personal injury may occur.
Do not attempt jumps or tricks with this vehicle.
Do not attempt to remove internal battery.
Do not use included USB cord for anything other than its intended purpose.
Always keep USB cord stored when not in use.
Adult supervision recommended.

FCC CAUTION

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received, including interference that may cause undesired operation.

NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Warranty

USA & Canada 30-Day Limited Warranty

New Bright Industries warrants to the original purchaser that this product will be free of defects in materials and workmanship for thirty (30) days from the date of purchase. In the event of such defect within the warranty period, New Bright will repair or replace the product at our sole discretion. This warranty does not cover damage resulting from unauthorized modifications, accident, misuse or abuse.

Should your item have a defect covered under this warranty, first call the toll free number listed below. Most problems can be resolved in this manner. If necessary, you will be issued a Return Authorization number (RA) and instructions on how to obtain a Product Return Form. The Product Return Form is to be used when returning a product to us (postage pre-paid and insured by the consumer).

When returning a defective product, please package the product, the Product Return Form and a copy of the dated sales receipt as proof of purchase. Be sure to mark the RA number on the Product Return Form. If the product is returned without a dated sales receipt, it will be excluded from coverage under this warranty. Please allow 4 to 6 weeks for delivery of repaired or replacement vehicles (depending on your location).

New Bright Industries’ liability for defects in materials and workmanship under this warranty shall be limited to repair or replacement at our sole discretion. In no event shall we be responsible for incidental, consequential or contingent damages (except in those states that do not allow this exclusion or limitation).