Victure BM50 Video Baby Monitor User Manual
- June 6, 2024
- Victure
Table of Contents
User Manual
BM50
Video Baby Monitor
Attention
Thank you for purchasing Victure Video Baby Monitor BM50. Now you can see and
hear your baby sleeping in the other room or you can monitor your elder kids
in their playroom. Before you use the device, please read this User Manual
carefully
- This product should be assembled by adults.
- Keep small parts away from children when assembling.
- This product is not a toy, do not allow children to play with it as a toy
- This baby monitor is not a substitute for responsible adult supervision
- Do not place the baby monitor cables in the cot or with the baby arm’s reach (at least 1 meter away)
- Keep the cords out of reach of children.
- Do not use the baby monitor near water or a heat source-.
- Only use the power adapters provided.
- Do not touch the power plug with sharp or metal objects.
Package Content
Overview of Your Baby Monitor
Controls(Baby Unit)
- Light sensor
- Lens
- Microphone
- Speaker
- Network Antenna
- Temperature sensor
- Power Interface
- Pair Button
- Power Indicator
Receiver (Parent Unit)
- TFT Screen
- Volume/ Brightness Adjust
- Power Button
- Menu Setting
- Navigation Key
- OK/Zoom Button
- Talk Button
- Split Screen Button
- Network Antenna 1
- Charging Interface 1
- Charging Indicator 1 12
- Microphone 1′ 1
- Bracket 14
- Speaker
Setting up Your Baby Monitor
Baby Unit power Supply
–Connecting the power adapter for the baby unit.
- Connect the small plug of the adapter to the Baby Unit and the other end to the power socket
- Only use the enclosed adapter (USB Type-C SV/1A)
WARNING
Strangulation Hazard: Children will be STRANGLED in cords. Keep this cord out
of the reach of children(more than 1 meter away)
Baby Unit power Supply
–Connecting the power adapter for the Parent Unit if it is in low
battery status.
- Connect the small plug of the adapter to the Parent Unit and the other end to the power socket
- Only use the enclosed adapter (USB Type-C 5V/2A)
- Press and hold the Power Button on the Parent Unit to turn it ON.
Main Screen Icons (Parent Unit)
Icons
|
Descriptions
---|---
| Camera and monitor connection signal strength
| Monitor sound level
| is on
| The VOX function is turned on, the white icon is displayed when it is turned
on, and a beep will sound when triggered Sound prompt, after red and white
alternate switching flashing for 10 seconds, it will turn back to white”
| Infrared Night Vision is on
| The Motion Detect function is turned on, and the white icon is displayed
when it is triggered.” Didi” prompt, display a red icon, and then change back
to white after 10 seconds.
| Screen magnification prompt
| The Temperature function is turned on, if the temperature exceeds the set
range, a beep will sound.
|
The Feeding Timer function is turned on. After the function is turned on, a “di di” will be emitted in the last 1 minute. The sound prompt also displays a red icon and countdown on the screen
| Battery power
| Long press the Talk button to display
| the single large monitoring screen, press the navigation button to go to the
camera PTZ Rotate up and down.
|
Under the single large monitoring screen, press the Submenu button to use the up and down navigation Navigation key to adjust the brightness, left and right navigation keys to adjust the sound level.
| After entering Dual mode/Quad mode, a check box will be displayed on the monitoring screen, select Set the frame at the top left of the monitoring screen, which represents the currently selected camera, monitoring The sound that the viewer hears at this time is that of the current camera, press the Menu button to set the menu Single is also to set the parameters of the current camera, press up/down/left/right to change the selected frame Switch between each camera, if you press the OK button, you can directly switch to the current selection Single-mode screen of the camera where the frame is located.
Main Menu Function (Parent Unit)
Menu Options
|
Descriptions
---|---
| Choose to play cradle tracks, sound size, and close settings
| Sound detection sensitivity setting
| Temperature detection setting
| the timer to remind you of feeding your baby or other things.
| Screen sleep function setting
| The Alarm”beep” will be triggered when image movement is detected
System Setting (Parent Unit)
Setting Options
|
Descriptions
---|---
Date Time| Seeing the date/ time
Pairing| Pair the camera you want( Max Support 2 Cameras)
Frequency| Change to the suitable Anti-screen Flicker mode
Alert Volume| Adjust the desired volume of Alert.
Language| Choose the language you want.
Default| Restore the monitor to its default setting
Firmware Info| Know the firmware version information
Technical Features
Signal Connection: 2.4GHz
Operating Temperature: -10C – + 45C (14 °F – 113 °F)
Operating Humidity: <85%
Parent Unit (Monitor)
LCD: 5.0 inch TFT
Resolution: 854*480
Battery: Li-Polymer 4000mAh
Power Input: USB Type-C 5V/1A
Baby Unit (Camera)
Image Sensor: 1/2.7″,CMOS
Camera Resolution: 1080P
Power Input: USB Type-C 5V/1A
PTZ Angel: Pan: 310°; Tilt:50°
IR LED: 8pcs 940nm Infrared Fill Light
Troubleshooting
Possible Problems
|
Solutions
---|---
How to turn on/off the baby monitor and turn on/off the screen?| Power on/off:
long-press the Power button for 5 seconds; union screen: short press the Power
button once;
What is the battery capacity? How long will it last? How long does it take to
fully charge?|
The standard battery capacity is 4000mAh; after a normal battery is fully
charged, it can be used for about 9 hours if it is in sleep mode.
It can be used for about 4.5 hours in the norm l bright right screen working
state; the battery starts to be charged from a completely empty condition, and
it can be fully charged in about 9 hours; the power indicator light is red
during charging, and the power indicator light is green when fully charged;
Why does the monitoring screen keep flashing?|
The flickering of the monitoring screen is because the frequency set by the
camera does not match the actual area. You can set the frequency of the
camera.
To solve the problem, first press the Menu button to enter the main menu, then
press the up and down buttons to select System Setting
–>—>Select
Why does no one pass by and record video?|
The camera has no PIR detection function, only image comparison, so as long as the image has a certain degree of change, it will record
Why does no one pass by and record video?|
After the screen is off, as long as there is an alarm trigger (vox, motion, temp, feed time) or short press the Power button, the screen will turn on;
Why is there a trigger but no alarm after the VOX function is turned on?|
It is possible that the sound level does not meet the requirements. You can set the VOX sensitivity to high. In addition, if the lullaby playback function is turned on, VOX function is invalid, you must turn off the lullaby to play VOX function to be effective.
FCC Statement
This device complies with Part 15 of the FCC rules. Operation is subject to
the following two conditions: 1) this device may not cause harmful
interference, and 2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
–Reorient or relocate the receiving antenna.
–Increase the separation between the equipment and receiver.
–Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
–Consult the dealer or an experienced radio/TV technician for help. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. Radiation Exposure
Statement.
For Monitor: To comply with FCC RF exposure compliance requirements, this
grant is applicable to only mobile configurations. The antennas used for this
transmitter must be installed to provide a separation distance of at least 20
cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.
For Receiver: The device has been evaluated to meet general RF exposure
requirements. The device can be used in portable exposure conditions without
restriction.
Warranty
All Victure products come with a limited warranty of 12 months from the date
of purchase. And we have a professional customer service team for your support
as soon as we can.
If you have any questions or confusion about our product or warranty, please
feel free to contact us. We will do our best to help you solve the problem
until you are satisfied. Victure Customer Care Service Mailbox:
bm.support@govicture.com
Victure Official Facebook: Search”Victure Video Baby Monitor” Complaint
Mailbox: support@govicture.com
WELCOME TO REGISTER YOUR WARRANTY AT FB ONLINE: “Victure Baby Monitor VIPs”
TO EXTEND YOUR LIFETIME WARRANTY!
Documents / Resources
|
Victure BM50 Video Baby
Monitor
[pdf] User Manual
BM50RX, 2AWNK-BM50RX, 2AWNKBM50RX, BM50 Video Baby Monitor, Video Baby Monitor
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>