HIKVISION C6S 4K Ultra HD Image Quality Security Dashcam User Manual

HIKVISION C6S 4K Ultra HD Image Quality Security Dashcam User Manual

Parts Introduction

1. RESET Button (Restore the device to defaults.)
2. TF Card Slot
3. Lens
4. Microphone
5. Speaker
6. Power Interface
7. MicroUSB Interface (It can be extended as 4G interface.)
8. Screen
9. Buttons

Installation

1. Clean the windshield and paste the electrostatic film onto it. Avoid introducing air bubbles. DO NOT paste the film repeatedly.

2. Peel off the release paper of 3M tape and install the dashcam onto the center of the electrostatic film. Connect the dashcam with one end of the power cord along the red line shown in the figure.

3. Connect the other end of power cord to the car charger and connect car charger to cigarette lighter.

4. Adjust the surveillance angle and the installation is completed. The tilt adjusting angle is from -10° to 10°.

Mobile Phone Connection

1. Scan the QR code to download and install the HikDashcam app.
2. Add the dashcam to the app.
   • Run the HikDashcam app.
   • Tap Wi-Fi Connection.
   • In the Wi-Fi list, select the Wi-Fi SSID of the target dashcam and enter the Wi-Fi password to build a connection.
   • You can set the parameters of the dashcam.
   • For iOS, you need to go to Wi-Fi settings of your phone to connect to the Wi-Fi of dashcam.
3. Edit the dashcam password to activate it to avoid abnormal recording after connecting to Wi-Fi.

Dashcam Wi-Fi default parameters:

• Wi-Fi SSID: HIKVISION-C6PRO-XXXX (XXXX refers to the last four characters of verification code.)
• Wi-Fi password: 1234567890 (please edit password after logging in for the first time.)

Function Description

Power On and Power Off
Power On: When you start up the engine, the dashcam powers on.
Power Off: When you turn off the engine, the dashcam powers off.

• Make sure you have connected the dashcam to power according to Step 2 and Step 3 in Installation section.
• The power mode of cigarette lighter may vary by different vehicle types. Some may be powered constantly. In this case, please make sure that the dashcam stops after you turn off the vehicle engine. Otherwise, insufficient voltage may occur to vehicle battery.

Recording
Two recording types are provided: Normal Reording and Emergency Recording. Sound and mute recordings are selectable. Sound recording is set as default. You can set audio settings on the device or turn off sound recoding in app.

Specifications

Humidity 95% or less.
Installation Type| General
Dimensions (L × W × H)| 90 × 88 × 70 mm (3.6ʺ × 3.5ʺ × 2.8ʺ)
Weight| Approx. 125 g (0.25 lb.)

Cautions

Safety Instruction
These instructions are intended to ensure that users can use the product correctly to avoid danger or property loss.
Cautions: Injury or equipment damage may occur if any of the cautions are neglected.

• In the use of the dashcam, you must be in strict compliance with the local laws and regulations.
• You are recommended to install the dashcam on the location of rear mirror to ensure the dashcam can record with the best surveillance view. DO NOT install the dashcam on the location that will block the driver’s sight.
• Keep the user manual properly for future reference. See initial connection of dashcam in user manual.
• Purchase the TF card from legal channel. To ensure safe and stable data transmission, it is recommended to use TF card of Class 10 or above.
• Format the new TF card first before using the card.
• To protect TF card from damage, shut down the dashcam before installing and uninstalling TF card.
• If the dashcam is directly connected with the vehicle power system, you are recommended to power off the dashcam when the engine is off. Disconnect cigarette lighter to avoid insufficient voltage and abnormal startup. Reconnect cigarette lighter to ensure dashcam work normally when you start the car again.
• The operating temperature is from -20 ̊C to 70 ̊C (-4 ̊F to 158 ̊F). To protect the dashcam, DO NOT use it in high temperature, low temperature, or high-humidity environments. Keep the dashcam from rain and dust.
• The manual is subject to update. The functions of the dashcam may vary according to different models.
• The driving assistance function of the device only sends alarm or warning to the driver and cannot replace the driver’s judgement and operation. With the device, you also should drive carefully to avoid traffic accident or violation. Pedestrian or object recognition failure or recognition error may occur due to external factors. DO NOT overly rely on the driving assistance function.

Troubleshooting

·   Check whether the 3M tape is tightly sticked to the **electrostatic film before the installation.**

Starting the dashcam failed.| ·   Check whether the vehicle is started and power supply is normal.

·   Check whether the car charger is tightly connected.

·   Restore to defaults: hold the RESET button until the

____startup music is heard.

·   Make sure the power cord is in good condition.

·   Make sure the power cord is tightly connected to the

__according interfaces.

·   Make sure that the dashcam started up successfully.

·   Check whether the TF card is inserted.

·   Check the status of TF card, e.g. its format, its lifespan.

·   Change TF card if it is not well.

The dashcam powers off easily.

Recording is abnormal and indicator is unlit.

Recording is blurred.

| ·   Make sure the protective film is peeled off.

·   Check whether the windshield or the lens of dashcam is blurred.

Recording is mute.| ·   Set audio settings on the device or turn on sound recording in HikDashcam app.

·   Turn on sound through the the audio control function

____of the dashcam.

·   Check whether the car charger is tightly connected.

·  Check whether the car charger is equipped with power

____supply interface of 5 VDC, ≥ 2 A.

·   Make sure HikDashcam app is installed.

·   Please restart the dashcam to the app.

Dashcam reboots itself.

Mobile phone cannot connect to dashcam.

The mobile phone cannot display recordings.

TF card is not detected when you connect dashcam to computer with the supplied power cord.

Wi-Fi connection takes a long time.

Dashcam Wi-Fi password is forgotten.

No GPS signal.

| ·   It may be relevant with the player or system of the phone. Please connect TF card to your computer and display the recordings.

·   Dashcam does not support data transmission and the supplied power cord is only for charging.

·   If you need to transfer data, please connect TF card to your computer.

·   It may be caused by the interferrence of the surrounding Wi-Fi signals. Please use the dashcam in an environment of less interferrence.

·   Shut down unnecessary programs in your phone to release some resources for HikDashcam app and reconnect Wi-Fi.

·   The default password is 1234567890. If you have revisied the password, regain the password by the following steps.

1. Hold the RESET button on dashcam until the startup music is heard and the dashcam is restored to defaults.

2. Go to Wi-Fi Connection interface in HikDashcam app.

3. Select Wi-Fi SSID and log in with default password 1234567890.

·   Check whether the GPS function is enabled.

Normally, the GPS function is enabled by default.

·   Make sure the device is not in the places of weak signal or no signal, such as underground garage.

·   Make sure there is no metal around the device because metal will interfere with GPS signal.

·    Make sure the location where the device is installed is not pastd with radiation protection film. The film will interfere with GPS signal.

Packing List

Regulatory Information

• this device must accept any interference, including interference that may cause undesired operation of the device.
• Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
• This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body.

EU Conformity Statement

This product and – if applicable – the supplied accessories too are marked with “CE” and comply therefore with the applicable harmonized European standards listed under the RE Directive 2014/53/EU, the EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU. 2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.recyclethis.info

2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info

FCC Information

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help with important announcement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

RF Exposure Statement
To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with a minimum distance of 15cm the radiator your body. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter.

About this Manual
The Manual includes instructions for using and managing the Product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons.

Trademarks

• HIKVISION and other Hikvision’s trademarks and logos are the properties of Hikvision in various jurisdictions.
• Other trademarks and logos mentioned are the properties of their respective owners.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>