HORIZON LOS01025 Mini-B 1/16 Scale 2WD Buggy Pro Roller Instruction Manual
- June 6, 2024
- Horizon
Table of Contents
- INSTRUCTION MANUAL
- SAFETY PRECAUTIONS AND WARNINGS
- REGISTER YOUR LOSI PRODUCT ONLINE
- RECOMMENDED ACCESSORIES
- CONTENTS
- QUICK START
- INSTALLING THE RECEIVER (NOT INCLUDED)
- INSTALLING THE STEERING SERVO (NOT INCLUDED)
- INSTALLING THE MOTOR ESC COMBO (NOT INCLUDED)
- INSTALLING THE BATTERY AND POWERING ON THE VEHICLE
- BINDING
- CONTROL TEST
- DRIVING PRECAUTIONS
- RUN TIME
- GETTING STARTED
- OPERATION
- TUNING, ADJUSTING AND MAINTAINING THE VEHICLE
- SERVICE/REPAIR
- TROUBLESHOOTING GUIDE
- LIMITED WARRANTY
- WARRANTY AND SERVICE CONTACT INFORMATION
- PARTS LISTINGS
- OPTIONAL PARTS
- EXPLODED VIEW
- Documents / Resources
HORIZON LOS01025 Mini-B 1/16 Scale 2WD Buggy Pro Roller
Scan the QR code and select the Manuals and Support quick links from the
product page for the most up-to-date manual information.
INSTRUCTION MANUAL
NOTICE
All instructions, warranties and other collateral documents are subject to
change at the sole discretion of Horizon Hobby, LLC. For up-to-date product
literature, visit horizonhobby.com or towerhobbies.com and click on the
support or resources tab for this product.
MEANING OF SPECIAL LANGUAGE
The following terms are used throughout the product literature to indicate
various levels of potential harm when operating this product:
WARNING: Procedures, which if not properly followed, create the
probability of property damage, collateral damage, and serious injury OR
create a high probability of superficial injury.
CAUTION: Procedures, which if not properly followed, create the
probability of physical property damage AND a possibility of serious injury.
NOTICE: Procedures, which if not properly followed, create a possibility
of physical property damage AND a little or no possibility of injury
WARNING: Read the ENTIRE instruction manual to become familiar with the
features of the product before operating. Failure to operate the product
correctly can result in damage to the product, personal property and cause
serious injury. This is a sophisticated hobby product. It must be operated
with caution and common sense and requires some basic mechanical ability.
Failure to operate this Product in a safe and responsible manner could result
in injury or damage to the product or other property. This product is not
intended for use by children without direct adult supervision. Do not use with
incompatible components or alter this product in any way outside of the
instructions provided by Horizon Hobby, LLC. This manual contains instructions
for safety, operation and maintenance. It is essential to read and follow all
the instructions and warnings in the manual, prior to assembly, setup or use,
in order to operate correctly and avoid damage or serious injury
WARNING AGAINST COUNTERFEIT PRODUCTS Always purchase from a Horizon
Hobby, LLC authorized dealer to ensure authentic high-quality Spektrum
product. Horizon Hobby, LLC disclaims all support and warranty with regards,
but not limited to, compatibility and performance of counterfeit products or
products claiming compatibility with DSM or Spektrum.
Age Recommendation: Not for children under 14 years. This is not a toy.
SAFETY PRECAUTIONS AND WARNINGS
- Always keep a safe distance in all directions around your model to avoid collisions or injury. This model is controlled by a radio signal subject to interference from many sources outside your control. Interference can cause momentary loss of control.
- Always operate your model in open spaces away from full-size vehicles, traffic and people.
- Always carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery packs, etc.).
- Always keep all chemicals, small parts and anything electrical out of the reach of children.
- Always avoid water exposure to all equipment not specifically designed and protected for this purpose. Moisture causes damage to electronics.
- Never place any portion of the model in your mouth as it could cause serious injury or even death.
- Never operate your model with low transmitter batteries.
REGISTER YOUR LOSI PRODUCT ONLINE
Register your vehicle now and be the first to find out about the latest option parts, product updates and more. Click on the Support tab at www.LOSI.com and follow the product registration link to stay connected.
RECOMMENDED ACCESSORIES
- Soft bristle brush for cleaning
- Startup Tool Set: Metric (DYN2834)
- Thread Lock
TOOLS INCLUDED
- 4-Way Wrench
- 1.5mm Hex L Wrench
- 2mm Hex L Wrench
Use only Dynamite® tools or other high-quality tools. Other tools can cause damage to the small screws and parts used on this model.
CONTENTS
INCLUDED| REQUIRED COMPONENTS| RECOMMENDED COMPONENTS|
PART NUMBER
---|---|---|---
Losi® Mini-B Roller| 2+ Channel Radio Control System| Spektrum DX5C DSMR 5CH
TX Only, SR315 Receiver combo| SPM5115C
High Torque Steering Servo with 20T Output Gear| Spektrum™ SX107 Micro Analog
Metal Gear Surface Servo| SPMSSX107
Motor / ESC| Dynamite® Brushless Motor/ESC 2-in-1 Combo, 6000Kv: Mini-T 2.0|
DYNS0501
Pinion| 18T| See parts list
2S Hardcase LiPo Battery| Spektrum 7.4V 800mAh 2S 50C Hardcase LiPo with EC2|
DYNB825H2
Charger| Spektrum SMART S1200 DC Charger, 1x200W| SPMXC1000
QUICK START
Please read the entire manual to gain a full understanding of the Mini-B vehicle, fine-tuning the setup and performing maintenance.
- Read the safety precautions found in this manual.
- Charge the battery. Refer to the included charging warnings and instructions for battery charging information.
- Ensure the transmitter and receiver is bound before installing the following components. Please refer to the binding instructions of your transmitter’s manual.
- Install a Receiver
- Install a Steering Servo
- Install a Motor/ESC combo.
- Install a fully charged battery in the vehicle.
- Power ON the transmitter and then the vehicle. Always power the transmitter ON before the vehicle and power it OFF after the vehicle has been powered OFF.
- Check the steering and throttle control directions. Verify that the servos are moving in the correct direction.
- Drive your vehicle.
- Perform any necessary maintenance.
INSTALLING THE RECEIVER (NOT INCLUDED)
-
Install servo tape to the receiver.
-
Install the receiver to the chassis.
-
Refer to transmitter/receiver manual for binding instructions.
-
Connect the steering linkage to the ball on the servo arm.
-
Connect the other end of the steering linkage to the ball on steering rack.
-
Connect the servo wire to the steering port on the receiver.
INSTALLING THE STEERING SERVO (NOT INCLUDED)
-
Mount the servo SX107 with the output shaft toward the left side of the chassis a as shown in the image below.
-
Center the steering servo using a servo checker. If no servo checker is available, the servo can be centered with the radio system. Power on the transmitter and ensure the steering trim is centered. Plug the servo into the receiver. Power on the receiver. The servo should power on and move to center.
-
With the servo centered, install the recommended (LOS311010) servo horn so the ball is 90 degrees as shown in the image below.
NOTE: The included aluminum servo horn requires a servo with a 20T output gear.
INSTALLING THE MOTOR ESC COMBO (NOT INCLUDED)
-
Remove two screws and the gear cover.
-
Install the recommended (DYNS0501) motor. Mount the motor on the center top and bottom holes of the mount.
-
Slide the 18T pinion gear on the motor shaft. Match the tooth profile of the pinion gear to the tooth profile of the spur gear, then tighten the pinion gear to the motor shaft. Ensure the set screw for the pinion gear is tightened on to the flat spot on the motor shaft, or the pinion gear will come off. The pinion should be centered to the spur gear as shown in the image below.
-
Route the ESC wire down the side guard using the supplied clip to guide the wire to the receiver.
-
Route the ON/OFF wire down the side guard using the supplied clip to guide the wire to mount the ON/OFF Switch.
-
Install the gear cover.
INSTALLING THE BATTERY AND POWERING ON THE VEHICLE
- If required, remove the body clips and lift the body.
- Remove the elastomer strap from the battery posts.
- Install the fully charged battery in vehicle.
- Re-secure the elastomer strap.
- Connect the battery to the ESC/receiver.
- Ensure the ESC/receiver is powered off.
- Power on the transmitter.
- Power on the ESC/receiver.
- Reinstall the body and the body clips.
BINDING
Refer to your transmitter/receiver manual for binding insturctions.
CONTROL TEST
Perform a control test with the vehicle wheels off the ground. If the wheels
rotate after the vehicle is powered ON, adjust the Throttle Trim until they
stop. To make the wheels move forward, pull the trigger. To reverse them, wait
for the wheels to stop, then push the trigger.
When moving forward, the wheels should maintain a straight line without any
steering wheel input. If not, adjust the Steering Trim, so the wheels maintain
a straight line without having to turn the steering wheel.
DRIVING PRECAUTIONS
- Maintain sight of the vehicle at all times.
- Inspect the vehicle for loose wheel hardware.
- Inspect the steering assembly for any loose hardware. Driving the vehicle off road can cause fasteners to loosen over time.
- Do not drive the vehicle in tall grass. Doing so can damage the vehicle or electronics.
- Stop driving the vehicle when you notice a lack of power. Driving the vehicle when the battery is discharged can cause the receiver to power off. You may lose control of the vehicle.
- Do not apply the throttle in forward or reverse if the vehicle is stuck. Applying throttle in this instance can damage the motor or ESC.
- After driving the vehicle, allow the electronics to cool to ambient temperature before using the next battery pack.
RUN TIME
The condition of a battery pack is also an important factor in both run time
and speed.
The battery connectors may become hot during driving. Batteries will lose
performance and capacity over time.
Driving the vehicle from a stop to full speed repeatedly will damage the
batteries and electronics over time. Sudden acceleration will also lead to
shorter run times.
TO IMPROVE RUN TIMES
- Keep your vehicle clean and well maintained.
- Allow more airflow to the ESC and motor.
- Change the gearing to a lower ratio. A lower ratio lowers the operating temperature of the electronics. Use a smaller pinion gear or larger spur gear to lower the gear ratio.
GETTING STARTED
-
Power on the transmitter
-
Power on the ESC.
-
Perform a test of the transmitter’s control of the vehicle with the vehicle’s wheels off the ground.
-
Start driving slowly, and, if the vehicle does not go straight, adjust the steering trim dial on the transmitter.
OPERATION
- ALWAYS turn on your transmitter before you turn on the receiver in the vehicle. Always power off the receiver before turning your transmitter off.
- ALWAYS operate your vehicle in a wide open area. Operating the vehicle in a small space or indoors can cause overheating at low speeds. Operating at low speed increases heat in the electronic speed control (ESC). Overheating can damage the vehicle and failure may result.
TUNING, ADJUSTING AND MAINTAINING THE VEHICLE
- Examine your vehicle on a regular basis.
- Use a brush to remove dirt and dust.
- Look for damage to the suspension arms and other molded parts.
- Re-glue the tires to the wheels, if necessary.
- Use suitable tools to tighten fasteners.
- Make sure the camber and steering linkages are not bent. Replace any bent linkages.
- Adjust the Toe and Camber settings, if necessary.
- Remove the shocks and inspect them for damage. Rebuild the shocks if oil is leaking.
- Inspect electronics and batteries for exposed wires. Repair exposed wires with shrink-wrap or replace the wire.
- Make sure the ESC and receiver are secure on the chassis. Replace the double sided tape, if necessary.
- Check the spur gear for wear.
SERVICE/REPAIR
RADIO/SPEED CONTROL AND MOTOR
If any problems other than those covered in the troubleshooting section arise, please call the appropriate electronics service department at 877 504 0233. They will be able to give the problem additional specific attention and provide instructions for the solution.
MAINTENANCE
If any questions other than those covered in the troubleshooting or maintenance sections arise, please call the appropriate Horizon product support department at 877 504 0233.
CLEANING
Performance can be hindered if dirt gets in any of the moving suspension parts. Use compressed air, a soft paintbrush, or a toothbrush to remove dust or dirt. Avoid using solvents or chemicals as they can actually wash dirt into the bearings or moving parts, as well as cause damage to the electronics.
SHOCK CLEANING
Oil-filled shocks will require regular maintenance due to the oil breaking down or getting dirty. This maintenance should be performed after about every 3–5 hours of use, depending on the driving conditions.
- Remove the shock from the vehicle.
- Remove the bottom cartridge from the shock body and dispose of fluid.
- Disassemble the shock. Clean thoroughly with a plastic- and electronic-safe degreaser (DYNE50001). Dry parts before assembly.
- Re-assemble the shock and refill the shock body with silicone fluid (22.5 weight recommended, TLR74003).
- Slowly move the shaft and piston up and down to remove air bubbles.
- Move the piston to the midway point of the body and install the bottom cartridge.
- Wipe off any overflowing fluid.
-
Re-install the shock on the vehicle.
RIDE HEIGHT ADJUSTMENT
Ride height is an adjustment that affects the way the vehicle jumps, turns and goes over bumps. Drop one end of the vehicle from approximately 6 inches (152 mm) in height onto a flat surface. When dropping the front of the vehicle, after the vehicle settles, make sure the front arms are equal and parallel to the flat surface.
Do the same with the rear to make sure both arms are parallel with the flat surface. Lowering the front ride height increases steering, but decreases traction. Lowering the rear ride height increases traction, but decreases steering.
TROUBLESHOOTING GUIDE
PROBLEM | POSSIBLE CAUSE | SOLUTION |
---|---|---|
Vehicle does not operate | Battery not charged or plugged in | Charge |
battery/plug in
ESC switch not “On”| Turn on ESC switch
Transmitter not “On” or low battery| Turn on/replace batteries
Motor runs but rear wheels do not rotate| Pinion not meshing with spur gear|
Adjust pinion/spur mesh
Pinion spinning on motor shaft| Tighten pinion gear setscrew on motor shaft
flat spot
Transmission gears stripped| Replace transmission gears
Drive pin broken| Check and replace drive pin
Steering does not work| Servo plug not in receiver properly| Make sure the
steering servo plug is connected to the receiver steering channel, noting
proper polarity
Servo gears or motor damaged| Replace or repair servo
Will not turn one direction| Servo gears damaged| Replace or repair servo
Motor does not run| Motor wire solder joint is damaged| Resolder the motor
wire with the proper equipment
Motor wire broken| Repair or replace as needed
ESC damaged| Contact Horizon Hobby Product Support
ESC gets hot
| Motor over-geared| Use smaller pinion or larger spur gear
Driveline bound up| Check wheels and transmission for binding
Poor run time and/or sluggish acceleration| Battery pack not fully charged|
Recharge battery
Charger not allowing full charge| Try another charger
Driveline bound up| Check wheels, transmission for binding
Poor range and/or glitching| Transmitter batteries low| Check and replace
Vehicle battery low| Recharge battery
Loose plugs or wires| Check all wire connections and plugs
LIMITED WARRANTY
What this Warranty Covers
Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the
product purchased (the “Product”) will be free from defects in materials and
workmanship for a period of 2 years from the date of purchase.
What is Not Covered
This warranty is not transferable and does not cover (i) cosmetic damage, (ii)
damage due to acts of God, accident, misuse, abuse, negligence, commercial
use, or due to improper use, installation, operation or maintenance, (iii)
modification of or to any part of the Product, (iv) attempted service by
anyone other than a Horizon Hobby authorized service center, (v) Product not
purchased from an authorized Horizon dealer, or (vi) Product not compliant
with applicable technical regulations or (vii) use that violates any
applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be
that Horizon will, at its option, either (i) service, or (ii) replace, any
Product determined by Horizon to be defective. Horizon reserves the right to
inspect any and all Product(s) involved in a warranty claim. Service or
replacement decisions are at the sole discretion of Horizon. Proof of purchase
is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER
THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability
HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY,
REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT,
NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event
shall the liability of Horizon exceed the individual price of the Product on
which liability is asserted. As Horizon has no control over use, setup, final
assembly, modification or misuse, no liability shall be assumed nor accepted
for any resulting damage or injury. By the act of use, setup or assembly, the
user accepts all resulting liability. If you as the purchaser or user are not
prepared to accept the liability associated with the use of the Product,
purchaser is advised to return the Product immediately in new and unused
condition to the place of purchase.
Law
These terms are governed by Illinois law (without regard to conflict of law
principals). This warranty gives you specific legal rights, and you may also
have other rights which vary from state to state. Horizon reserves the right
to change or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot provide warranty
support or service. Once assembly, setup or use of the Product has been
started, you must contact your local distributor or Horizon directly. This
will enable Horizon to better answer your questions and service you in the
event that you may need any assistance. For questions or assistance, please
visit our website at www.horizonhobby.com, submit a Product Support Inquiry,
or call the toll free telephone number referenced in the Warranty and Service
Contact Information section to speak with a Product Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the
country you live and use the Product in, please use the Horizon Online Service
Request submission process found on our website or call Horizon to obtain a
Return Merchandise Authorization (RMA) number. Pack the Product securely using
a shipping carton. Please note that original boxes may be included, but are
not designed to withstand the rigors of shipping without additional
protection. Ship via a carrier that provides tracking and insurance for lost
or damaged parcels, as Horizon is not responsible for merchandise until it
arrives and is accepted at our facility. An Online Service Request is
available at http://www.horizonhobby.com/content/servicecenter_render-service-
center. If you do not have internet access, please contact Horizon Product
Support to obtain a RMA number along with instructions for submitting your
product for service. When calling Horizon, you will be asked to provide your
complete name, street address, email address and phone number where you can be
reached during business hours. When sending product into Horizon, please
include your RMA number, a list of the included items, and a brief summary of
the problem. A copy of your original sales receipt must be included for
warranty consideration. Be sure your name, address, and RMA number are clearly
written on the outside of the shipping carton.
NOTICE: Do not ship Li-Po batteries to Horizon. If you have any issue with a Li-Po battery, please contact the appropriate Horizon Product Support office.
Warranty Requirements
For Warranty consideration, you must include your original sales receipt
verifying the proof-of-purchase date. Provided warranty conditions have been
met, your Product will be serviced or replaced free of charge. Service or
replacement decisions are at the sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service will be completed
and payment will be required without notification or estimate of the expense
unless the expense exceeds 50% of the retail purchase cost. By submitting
the item for service you are agreeing to payment of the service without
notification. Service estimates are available upon request. You must include
this request with your item submitted for service. Non-warranty service
estimates will be billed a minimum of ½ hour of labor. In addition you will be
billed for return freight. Horizon accepts money orders and cashier’s checks,
as well as Visa, MasterCard, American Express, and Discover cards. By
submitting any item to Horizon for service, you are agreeing to Horizon’s
Terms and Conditions found on our website http://www.horizonhobby.com/content
/service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging return shipment of the un-serviced Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon will hold non-compliant Product for a period of 60 days from notification, after which it will be discarded.
WARRANTY AND SERVICE CONTACT INFORMATION
Country of Purchase| Horizon Hobby| Contact Information|
Address
---|---|---|---
United States of America| Horizon Service Center (Repairs and Repair
Requests)|
servicecenter.horizonhobby.com/RequestForm/|
2904 Research Rd Champaign, Illinois 61822 USA*
Horizon Product Support (Product Technical Assistance)|
productsupport@horizonhobby.com
877-504-0233
Sales| websales@horizonhobby.com
800-338-4639
European Union| Horizon Technischer Service|
service@horizonhobby.de
+49 (0) 4121 2655 100
| Hanskampring 9 D 22885 Barsbüttel, Germany
PARTS LISTINGS
PART # | ENGLISH |
---|---|
LOS210019 | Body, Wing, Blue/White |
LOS210020 | Body, Wing, Black/White |
LOS210022 | Wing, Precut, Clear (2) |
LOS210023 | Body, Wing, Yellow/White |
LOS211011 | Front Bulkhead, Front Brace, Left/Right |
LOS211012 | Servo Mount, Servo Saver |
LOS211013 | Bellcrank, Drag Link, Set |
LOS211016 | Gear Cover with Plug |
LOS211020 | Chassis & Mud Guards |
LOS211021 | Waterfall, Front Body Post |
LOS211022 | Battery Strap, Elastomer |
LOS212011 | Wheel Hex, Pin (2) |
LOS212012 | Rear Axle (2) |
LOS212013 | Dogbone (2) |
LOS212014 | Front Axle (2) |
LOS212015 | Slipper Hardware |
LOS212016 | Spur Gear with Slipper Pads 60T 0.5M |
LOS212018 | Differential Gear, Idler Gear |
LOS212019 | Outdrive Sun Spider Gear Set |
LOS212020 | Top Shaft |
LOS212021 | Transmission Case & Motor Plate |
LOS212022 | Losi .5 Mod Pinion Gear, 18T, 2mm |
LOS213000 | Front Shock Set Complete |
LOS213001 | Rear Shock Set Complete |
LOS213002 | Shock O-Ring Set |
LOS214003 | Suspension Arm Set, Front/Rear |
LOS214005 | Caster Block & Front Camber Block |
LOS214006 | Spindle & Hub Set |
LOS214008 | Shock Standoff Bushing |
LOS214009 | Rear Pivots & Bumper |
LOS214010 | Front Pivot & Bumper |
LOS214012 | Front/Rear Shock Tower, Wing Stay |
LOS214013 | Adjustable Link Set |
LOS214014 | Rear Shock Springs (3 pair) |
LOS214015 | Front Shock Springs (3 pair) |
LOS214016 | Rod End Set |
LOS214017 | Rear Shock Springs (3pr) |
LOS214018 | Front Shock Springs (3pr) |
LOS216002 | Ball Stud (4) |
LOS216003 | Screw Set, Button Head |
LOS216004 | Screw Set, Flat Head |
LOS216005 | King Pin Set |
LOS217001 | 4 x 7 x 2.5mm Ball Bearing (4) |
LOS214016 | Rod End Set |
LOS214017 | Rear Shock Springs (3pr) |
LOS214018 | Front Shock Springs (3pr) |
LOS41018 | BK Bar, Rear Mounted, White (2) |
OPTIONAL PARTS
PART # | ENGLISH |
---|---|
DYNC2030 | Prophet Sport Mini 50W Charger |
DYNT2010 | Machined Nut Driver Set (4), Metric |
DYNB825H2 | 7.4V 800mAh 2S 50C Hardcase LiPo |
DYNC0095 | Adapter: EC2 Device/Banana Plug |
DYNS0501 | Brushless Motor/ESC Combo: 6000Kv |
LOS210021 | Body, Wing, Clear |
LOS216001 | Body Clips (6) |
LOS311001 | Front Pivot, Aluminum |
LOS311002 | Bellcrank Drag Link Aluminum |
LOS311003 | Caster Black, 0 Deg, L/R, Aluminum |
LOS311005 | Hub Set, Rear, Aluminum |
LOS311006 | Pivot Block Set, Rear, Aluminum |
LOS311007 | Front Brace Set, Aluminum |
LOS311008 | Servo Mount Set, Aluminum |
LOS311009 | Camber Black, Front, Aluminum |
LOS311010 | Servo Arm, Aluminum |
LOS312004 | Hex Set, Rear Axle, Aluminum |
LOS312005 | Adjustable Motor Plate |
LOS312007 | Slipper Plate, HD |
LOS314004 | Shock Assembly, Front, Aluminum (2) |
LOS314005 | Shock Assembly, Rear, Aluminum (2) |
EXPLODED VIEW
©2021 Horizon Hobby, LLC.
Losi, Mini-B, Dynamite, Prophet, EC2, and the Horizon Hobby logo are
trademarks or registered trademarks of Horizon Hobby, LLC.
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
Documents / Resources
|
HORIZON LOS01025 Mini-B 1/16 Scale 2WD Buggy Pro
Roller
[pdf] Instruction Manual
LOS01025, Mini-B 1 Scale 2WD Buggy Pro Roller, Mini-B 16 Scale 2WD Buggy Pro
Roller
---|---
|
HORIZON LOS01025 Mini-B 1/16 Scale 2WD Buggy Pro
Roller
[pdf] Instruction Manual
LOS01025 Mini-B, 1-16 Scale 2WD Buggy Pro Roller, 2WD Buggy Pro Roller, Pro
Roller, Roller, Buggy Pro
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>