COOSPO BC200 Bluetooth GPS Bicycle Computer For Road Bike User Manual

USER MANUAL
All About Passion

Button function

| GPS signal status/Icon flashing means acquiring satellite signals
Satellite signals available
No satellite signal
Battery level
Paused
Auto Pause
Cadence sensor: The icon is on when connected/The icon is flashing when the sensor is disconnected or under searching
Speed sensor: The icon is on when connected/The icon is flashing when the sensor is disconnected or under searching
Power meter: The icon is on when connected / The icon is flashing when the sensor is disconnected or under searching
Heart rate monitor: The icon is on when connected / The icon is flashing when the sensor is disconnected or under searching
It’s available to scroll the page up and down by pressing the button
It’s not available to scroll the page up and down by pressing the button
Bluetooth accessory
ANT+ accessory

Standard Accessories

Standard Mount Installation

a.How to Install

b. Out front mount installation

Charging

1. Please charge the device before first time use.
2. Please use DC 5V power adapter for charging.
3. During the charging, the battery icon will flash until fully charged.

Initial Setup

1. For the 1st time use, please select the language before use.
2. User Profile Setting (To make the exercise calculation more accurate, please set the user profile correctly)
3. Bike Profile Setting.

Total Distance: Select and confirm to reset the total distance
Spd Source: Set the priority for the source of the speed
Common wheel size and circumference(Wheel Size L (mm))

12 × 1.75 935mm
14 × 1.5 1020mm
14 × 1.75 1055mm
16 × 1.5 1185mm
16 × 1.75 1195mm
18 × 1.5 1340mm
18 × 1.75 1350mm
20 × 1.75 1515mm
20 × 1-3/8 1615mm
22 × 1-3/8 1770mm
22 × 1-1/2 1785mm
24 × 1 1753mm
24×3/4 Tubular 1785mm
24 × 1-1/8 1795mm
24 × 1-1/4 1905mm| 24 × 1.75 1890mm
24 × 2.00 1925mm
24 × 2.125 1965mm
26 × 1.75 2023mm
26 × 1.95 2050mm
26 × 2.00 2055mm
26 × 2.10 2068mm
26 × 2.125 2070mm
26 × 2.35 2083mm
26 × 3.00 2170mm
26 × 7/8 1920mm
26 × 1(59) 1913mm
26 × 1(65) 1952mm
26 × 1.25 1953mm
26 × 1-1/8 1970mm| 26 × 1-3/8 2068mm
26 × 1-1/2 2100mm
26 × 1.40 2005mm
26 × 1.50 2010mm
27 × 1 2145mm
27 × 1-1/8 2155mm
27 × 1-1/4 2161mm
27 × 1-3/8 2169mm
27.5×1.75 2114mm
27.5×2.125 2174mm
27.5×1.5 2074mm
27.5×1.95 2146mm
29×2.1 2288mm
29×2.2 2298mm
29×2.3 2326mm| 650× 35A 2090mm
650 × 38A 2125mm
650 × 38B 2105mm
700 × 18C 2070mm
700 × 19C 2080mm
700 × 20C 2086mm
700 × 23C 2096mm
700 × 25C 2105mm
700 × 28C 2136mm
700 × 30C 2170mm
700 × 32C 2155mm
700C Tubular 2130mm
700 × 35C 2168mm
700 × 38C 2180mm
700 × 40C 2200mm
---|---|---|---

Other Settings

Zone:
Set the value for each heart rate zones, power zones, and cadence
zones
Alarm:
Set the alarm for heart rate, power, and cadence.
The device will beep if it reached to the preset value, and a warning message will pop up during the cycling.
Smart Pause:
When this function is turned on, the cycling recording will be paused automatically when the speed is 0.
It will get resumed when the speed is detected.
Altitude:
Set the numbers here to calibrate the current altitude.
Smart Lap:
Set the location or the distance used for smart lap counting.
Tone:
Set the key tone and the warning tone.
Back Light:
Set the mode of how to turn the backlight off and the brightness.
Unit:
Set the unit to Metric System or Imperial System.

Page Setting

1. Set the display content in the page setting.

2. The content to be displayed on the self-defined page.

Connecting the Sensors

Please make sure the sensors are in wake-up mode( for example the heart rate monitor should be worn properly, for cadence, speed, and power sensor, rotate the crank or the wheel to wake it up). Connection completed

Add New Sensor and Turn off Old Sensor
Select the desired sensor, and then select to connect a sensor or turn off the old sensor in the popped up window

Power Calibration
Select Power, and then select Calibrate in the popped up window

Power calibration only works in ANT+ power meter, the Bluetooth power meter doesn’t support this function

Starting a Ride

Once the device is turned on, it will automatically search for satellite signals, it may take 15~90 seconds to acquire signals. Please make sure you acquire the satellite signal for the first time use

Display and Button

View History

Sync Data

USB connection

1. Turn on the device’s sync function “USB connection”.
2. Connect the device to the computer with a USB cable.
3. The computer will recognize the device as a new disk, find the folder “fit activity” and copy the files in the folder to the computer.
4. Upload the activity file(.fit) to www.strava.com to view the data

Bluetooth Connection

1. Download CoospoRide in Google Play or App Store
   IOS 7.0 or above, iPhone 4s model or above
   Android 4.3 or above with Bluetooth 4.0

2. Go to ‘Sync’ on-bike computer, select `BLE Connect’ to enable Bluetooth

3. Open Coosporide app, turn on phone Bluetooth, go to ‘bind your computer

4. Select BC200 to enter the search status

5. Click BC200-xxxxxxx to connect

Specifications

French/Turkish/English
Battery Type| 1300 mAh| GPS| GPS & BDS &Glonass
Self-Defined Display| 5 pages| Parameter Display| 70+
Size| 60 x 88 x 20 mm| Laps Count| Yes
Waterproof| IP67| Zone Alert| Yes
Storage Format| lit File| Battery Life| GPS 36 hours continuous use
Supported Devices| ANT+ & BLE: Heart Rate Monitor, Speed Sensor, Cadence Sensor, Speed & Cadence 2 in 1 Sensor, Power Meter

Attentions

The information contained in this manual is for reference only. The product described above may be subject to alteration owing to the manufacturer’s continuing research and development plans without prior notice.

Disclaimer

The information contained in this manual is just for reference. The product described above may be subject to alteration owing to the manufacturer’s continuing research and development plans, without making an announcement in advance.
We shall not bear any legal responsibility for any direct or indirect, accidental or special damages, losses, and expenses arising from or in connection with this manual or the contained product.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>