COOSPO BC200 Wireless Bicycle GPS Computer User Manual

: June 5, 2024
: COOSPO

COOSPO BC200 Wireless Bicycle GPS Computer

COOSPO-BC200-Wireless-Bicycle-GPS-Computer-

Button function

COOSPO-BC200-Wireless-Bicycle-GPS-Computer-fig-1

Icons

Icon Description

GPS signal status/Icon ﬂashing means acquiring
satellite signals Satellite signals are available
No satellite signal
Battery level
Paused
Auto Pause
Cadence sensor: The icon is on when connected/The icon is ﬂashing when the sensor is disconnected or under searching
Speed sensor: The icon is on when connected/The icon is ﬂashing when the sensor is disconnected or under searching
Power meter: The icon is on when connected / The icon is ﬂashing when the sensor is disconnected or under searching
Heart rate monitor: The icon is on when connected / The icon is ﬂashing when the sensor is disconnected or under searching
It’s available to scroll the page up and down by pressing the button
It’s not available to scroll the page up and down by pressing the button
Bluetooth accessory
ANT+ accessory

Standard Accessories

Main Device x1
Charging Cable x1
User Manual x1
Out Front Bike Mount x1
Rubber Pad for Out Front Mount x2
Standard Bike Mount x1
Rubber Pad for Standard Bike Mount x1
Rubber Ring (Big x 2, Small x 2)
Screw Wrench x1

How to Install

Standard Mount Installation

Install the rubber pad onto the mount
Tie the mount onto the bar with the rubber rings
Tie up the mount
Install the main device onto the mount
Rotate the main device for 90 degrees
Installation completed

Out front mount installation

COOSPO-BC200-Wireless-Bicycle-GPS-Computer-fig-20

Install the rubber pad onto the handlebar
Unscrew the screw in the mount
Install the mount onto the handlebar on the rubber pad, tighten up the screw
Install the main device onto the mount
Rotate the main device for 90 degrees
Installation completed

Charging

Please charge the device before ﬁrst time use.
Please use DC 5V power adapter for charging.
During the charging, the battery icon will ﬂash until fully charged.

The product has a built-in battery. Do not throw the product into a ﬁre. Please choose an adapter that meets the rated voltage of the device to charge the device to avoid damage to the device.

Initial Setup

For the 1st time use, please select the language before use.
User Proﬁle Setting (To make the exercise calculation more accurate, please set the user proﬁle correctly)
Bike Proﬁle Setting.

Total Distance: Select and conﬁrm to reset the total distance Spd Source: Set the priority for the source of the speed

Common wheel size and circumference(Wheel Size L (mm))

12 × 1.75 935mm
14 × 1.5 1020mm
14 × 1.75 1055mm
16 × 1.5 1185mm
16 × 1.75 1195mm
18 × 1.5 1340mm
18 × 1.75 1350mm
20 × 1.75 1515mm
20 × 1-3/8 1615mm
22 × 1-3/8 1770mm
22 × 1-1/2 1785mm
24 × 1 1753mm
24×3/4 Tubular 1785mm
24 × 1-1/8 1795mm
24 × 1-1/4 1905mm
24 × 1.75 1890mm
24 × 2.00 1925mm
24 × 2.125 1965mm
26 × 1.75 2023mm
26 × 1.95 2050mm
26 × 2.00 2055mm
26 × 2.10 2068mm
26 × 2.125 2070mm
26 × 2.35 2083mm
26 × 3.00 2170mm
26 × 7/8 1920mm
26 × 1(59) 1913mm
26 × 1(65) 1952mm
26 × 1.25 1953mm
26 × 1-1/8 1970mm
26 × 1-3/8 2068mm
26 × 1-1/2 2100mm
26 × 1.40 2005mm
26 × 1.50 2010mm
27 × 1 2145mm
27 × 1-1/8 2155mm
27 × 1-1/4 2161mm
27 × 1-3/8 2169mm
27.5×1.75 2114mm
27.5×2.125 2174mm
27.5×1.5 2074mm
27.5×1.95 2146mm
29×2.1 2288mm
29×2.2 2298mm
29×2.3 2326mm
650× 35A 2090mm
650 × 38A 2125mm
650 × 38B 2105mm
700 × 18C 2070mm
700 × 19C 2080mm
700 × 20C 2086mm
700 × 23C 2096mm
700 × 25C 2105mm
700 × 28C 2136mm
700 × 30C 2170mm
700 × 32C 2155mm
700C Tubular 2130mm
700 × 35C 2168mm
700 × 38C 2180mm
700 × 40C 2200mm
700 × 42C 2224mm
700 × 44C 2235mm
700 × 45C 2242mm
700 × 47C 2268mm

Other Settings

Zone:
Set the value for each heart rate zones, power zones, and cadence zones
Alarm:
Set the alarm for heart rate, power, and cadence. The device will beep if it reached the preset value, and a warning message will pop up during the cycling.
Smart Pause:
When this function is turned on, the cycling recording will be paused automatically when the speed is 0. It will get resumed when the speed is detected.
Altitude:
Set the numbers here to calibrate the current altitude.
Smart Lap:
Set the location or the distance used for smart lap counting.
Tone:
Set the key tone and the warning tone.
Back Light:
Set the mode of how to turn the backlight oﬀ and the brightness.
Unit:
Set the unit to Metric System or Imperial System.
Time:
Set time format 12/24; time zone setting.
Language:
Set language.
Storage:
Data overwrite setting; clear historical record.
Factory Reset:
Factory reset and wipe all data.
About:
Check Ant+ ID, ﬁrmware, and hardware version.

Page Setting

Set the display content in the page setting.
The content to be displayed in the self-deﬁned page.

Connecting the Sensors

Please make sure the sensors are in wake-up mode( for example the heart rate monitor should be worn properly, for cadence, speed, and power sensor, rotate the crank or the wheel to wake it up). COOSPO-BC200-Wireless-Bicycle-GPS-
Computer-fig-29

Connection completed

Add New Sensor and Turn oﬀ Old Sensor
Select the desired sensor, and then select to connect a new sensor or turn oﬀ the old sensor in the popped-up window

Power Calibration
Select Power, and then select Calibrate in the popped-up window COOSPO-
BC200-Wireless-Bicycle-GPS-Computer-fig-32

Power calibration only works in the ANT+ power meter, the Bluetooth power meter doesn’t support this function

Starting a Ride

Once the device is turned on, it will automatically search for satellite signals, it may take 15~90 seconds to acquire signals. Please make sure you acquire the satellite signal for the ﬁrst time use

Display and Button

View History

Press the button to scroll up and down COOSPO-BC200-Wireless-Bicycle-GPS-
Computer-fig-35

Sync Data

USB connection

Turn on the device’s synchronization function “USB connection” (long press the lower right button in standby mode to quickly enter the USB synchronization function);
Connect the device to the computer with a USB cable.
The computer will recognize the device as a new disk, ﬁnd the folder “ﬁt activity”, and copy the ﬁles in the folder to the computer.
Upload the activity ﬁle(.ﬁt) to www. strava.com to view the data.

Bluetooth Connection

Download CoospoRide in Google Play or App Store

Applicable Smart Phones

IOS 7.0 or above, iPhone 4s model or above Android 4.3 or above with Bluetooth 4.0
Turn on the Bluetooth connection synchronization function of the cycling computer(long press the upper right button in the standby state to quickly enter the Bluetooth synchronization function);
Open the CoospoRide App, enter the step of binding the cycling computer, and select the cycling computer named BC200 in the device list to bind the device (the mobile phone needs to enable Bluetooth and allow Bluetooth permission);
Click to connect cycling computer;
Select the exercise record you want to sync and click sync.

Specifications

Display| LCD, 2.6 in| Backlights

parameter

| Yes
---|---|---|---
File Transfer| USB/Bluetooth(APP)| DEai cphlaPyagde| 2~9

Spaminaish/Rususigaun

Wireless

Battery Type

aara e

| GPS & BDS & Glonass
Di ay

Size

| 5 pages

60 x 88 x 20 mm

| Di play d

Laps Count

| 70+

Yes

Attentions
The information contained in this manual is for reference only. The product described above may be subject to alteration owing to the manufacturer’s continuing research and development plans without prior notice.

Disclaimer
The information contained in this manual just for reference. The product described above may be subject to alteration owing to the manufacturer’s continuing research and development plans, without making an announcement in advance. We shall not bear any legal responsibility for any direct or indirect, accidental or special damages, losses, and expenses arising from or in connection with this manual or the contained product.

FCC statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oﬀ and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit diﬀerent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Changes or modiﬁcations not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

this device may not cause harmful interference, and.
this device must accept any interference received, including interference that may cause undesired operation.

IC statement
This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Contact your local government or a retailer for additional information.

Do not open or modify the product.
Do not disassemble or attempt to service this product.
This product is safe under normal and reasonably foreseeable operating conditions.
If the product is operating improperly, call COOSPO support.
The product must be returned to the manufacturer for any service or repair.