coospo H808S Bluetooth Heart Rate Monitor Chest Strap User Manual

H808S Bluetooth Heart Rate Monitor Chest Strap
User Manual
SCAN for more.https://www.coospo.com/download-center-h808s/

Standard Accessories

Product Introduction
H808S transmits real-time heart rate data through Bluetooth or ANT+ to heart rate receiving device, sports, and health App, helping you to manage your exercise intensity scientifically. This user manual will help you to use the product better, please keep it for reference.
Note: This product is used for sports purposes only and it is not meant to replace any medical device.

Function and Operation

Attention: Please be wearing the heart rate monitor first before attempting to pair it with your phone. If you aren’t wearing the monitor it will be in sleep mode and cannot be found by Bluetooth.
Wearing the Heart Rate Monitor

1. Moistening the electrode areas of the chest strap.
2. Attaching the heart rate Monitor to the chest strap, marked ‘L’ towards the Left.
3. Adjusting the length of the chest strap so that it can be fastened tightly but comfortably to your body. Be sure that the moist electrode areas are firmly against your skin and that the front of the Monitor is in a central and upright position.
4. When two “beep” sounds are heard, the LED flashes green, indicating that the heart rate sensor has been worn correctly and a heart rate signal has been detected.

Connect to the App

1. Turning on Bluetooth:
   Setting-Toggle Bluetooth to ON position.
   Don’t search for the device or try to pair on this page, just turn on Bluetooth and go to the Fitness App!

2. Start App and connect with the device in the App.

3. When this device is paired with App via Bluetooth, the blue light starts to flash.

4. When the heart rate monitor is removed, a “beep” will be heard, indicating that the product stops working.

Connecting with ANT+ Watch

1. Refer to the first page of ‘Wearing the Heart Rate Monitor’ to correctly wear the heart rate Monitor.
2. Find and add H808S to the ANT+ device list.
3. Follow the prompts on the watch to start training and view your real-time heart rate data on the display.

Maintenance

H808S is high-tech electronic equipment. Following the product’s nursing instructions can ensure the stability of the product and prolong its service life.

1. Heart Rate Monitor
   Detach the connector from the strap after each use and dry the connector with a soft towel. Do not use cleaning chemicals.

2. Chest Strap
   Rinsing the strap under running water and hang it to dry after each use. Cleaning straps in a washing machine or dryer is strongly prohibited.

Never use cleaning chemicals.
(Cleaning chemicals may cause rapid aging of the strap and shorten the service life.)
Do not stretch the strap or bend the electrode areas sharply.
Do not store the heart rate Monitor in a wet and gas-tight environment to prevent snap oxidation. Please store it in a cool dry environment.

Battery Replacement

If the device cannot be detected, please consider replacing the battery.

1. Use a coin, clip the groove, rotate it in the OPEN direction, and open the battery door.
2. Remove batteries, and properly dispose of used batteries in accordance with local environmental regulations.
3. Place the new battery in the battery bin (positive+up) correctly and rotate the battery door in the reverse direction of OPEN with a coin until the battery door is covered.

To avoid danger, batteries should be kept away from children.

Specifications

Applicable Smart Phones
IOS 7.0 or above, iPhone 4s model or above
Android 4.3 or above with Bluetooth 4.0

Compatible Apps

CoospoRide, Wahoo Fitness, Zwift, Openrider, Runkeeper, Endomondo, Nike+ Run Club, Sports Tracker, Polar Beat, Apple Health, Heartool, or other Apps with heart rate display features.
Note: When using Nike+ Run Club, please refer to the steps for displaying heart rate data in the App running settings.

FCC statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and.
2. This device must accept any interference received, including interference that may cause undesired operation

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Contact your local government or a retailer for additional information.

• Do not open or modify the product.
• Do not disassemble or attempt to service this product.
• This product is safe under normal and reasonably foreseeable operating conditions.
• If the product is operating improperly, call COOSPO support.
• The product must be returned to the manufacturer for any service or repair.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>