iclever BTH12 Wireless Kids Headphone User Manual
- June 6, 2024
- iclever
Table of Contents
Wireless Headphones
Model: BTH12
User Manual
Package Contents
1x clever BTH12 Wireless Headphones
Product Diagram
1. Power Button
2. LED Indicator
3. Microphone
4. 3.5mm Audio Input
5. Type-C Charging Port| 6. Volume – / Previous Track
7. MFB Button
8. Volume + / Next Track
9. Light Mode Switch Button
---|---
On / Off
-
Power on:
Switch the button to the “ON” direction. Then the LED indicator flashes blue for 1 second, and the colorful lights are on. -
Shutdown:
Switch the button to “OFF direction, and the headphone is turned off. The LED indicator flashes blue for 1 second and then goes off.
Bluetooth Pairing
- In the power-on state, switch the button to the “ON” direction; the colorful lights are on; Bluetooth enters the pairing state, and the red and blue lights flash alternately.
- Turn on the Bluetooth of the mobile phone. Then find and select the “iClever-BTH12” Bluetooth pairing name in the device list for Bluetooth pairing connection.
Light Mode Switching
Short press the light mode switch button, and you can switch multiple light modes at will.
Volume Limit Gear Switching
- Press and hold the “+” & buttons at the same time to switch the volume limit to 74dB, and the voice broadcast to “74dB”.
- Press and hold the “+” & “– buttons at the same time to switch the volume limit to 85dB, and the voice broadcast to “85dB”.
- Press and hold the “+” & “-Is buttons at the same time to switch the volume limit to 94dB, and the voice broadcast to “94dB”.
Note : The default power-on and factory reset are at 94dB volume limit.
Operation of Buttons
Volume Up | Short press the “+” button. |
---|---|
Volume Down | Short press the “-” button. |
Next Track | Press and hold the “+” button for 2 seconds. |
Previous Track | Press and hold the “-” button for 2 seconds. |
Play / Pause | Press the MFB button once. |
Answer / End A Call | Press the MFB button once. |
Reject A Call | Keep pressing the MFB button for seconds. |
Activate Siri | Press the MFB button twice. |
Clear The Pairing List | Press and hold the “+” button and “-” button |
simultaneously for 4 seconds in the
power-on state to clear the pairing list. Then the headphone will automatically enter
a pairing state.
Frequency band | 2.402GHz-2.480GHz |
---|---|
Potenza massima di trasmissione | 8dBm |
Voice Prompt
Power On | Power on |
---|---|
Power Off | Power off |
Pairing | Pairing |
Successful Pairing | Connected |
Disconnection | Disconnected |
Low Power | Battery Low |
How to Charge the Headphone
Connect the Type-C cable to the Type-C port on the headphone, and a 5V power outlet (power adapter is not included). The indicator light will glow red to indicate charging. When the headphone is fully charged, the indicator light will change from red to blue.
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions (1)This device may not cause harmful
interference. (2)This device must accept any interference received, including
interference that may cause undesired operation.
IC Caution
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
Hereby, Thousandshores Deutschland GmbH declares that the radio equipment type Wireless Headphones BTH12 is in compliance with Directive 2014/53/EU. The full text of the EU declaration conformity is available at the following internet address: Http://files.iclever.com/BTH12-DOC- EN.pdf