DYNALOG DR-DF100B Mini Drone for Kids User Manual
- June 9, 2024
- DYNALOG
Table of Contents
DR-DF100B Mini Drone for Kids
User Manual
One Key Return
Press and hold the button, then the drone will return along the parallel
direction where the tail of the drone pointed when the drone took off the last
time. The LEDs on the drone keep flashing when the drone is returning.
Press and hold the button again or move the Right Control Stick forward to
cancel this mode, or the drone will keep flying back. 
High-Speed Rotation
Press the button to make the drone rotate at high speed. Press the button
again or move the Right Control Stick to any direction to exit this mode.
Note: This function can’t be activated when the battery of the drone is low.
Circle Fly
In the case of barrier-free within 5m radius around the drone, press the a
button to fly the drone in circle.
Press the button again or move the Right Control Stick to any direction to
exit this mode.
Note: This function can’t be activated when the
battery of the drone is low.
Photo/Video
Please connect the drone to your mobile device first (refer to Page 19), then
go to the App Dynalog Casper to check your photos and videos. Press the button
to take a photo.
Press the button to start recording a video; press it again to stop recording
and save the video.
Altitude Hold/Hover
This is one of the default settings of the drone. When you release the Left Control Stick after an ascent/descent action, the drone will hover at the current flight height For a stable flight, press the trim buttons to adjust accordingly.
Emergency Stop
Press and hold the button, then the drone will stop in the airand fall.
Note: It’s NOT recommended to use this function during normal flight for
landing, which may result in serious damage for your drone.
App Operation Guide
1. App Downloading and Installation
Download and install Dynalog Casper into your mobile device from App
Store'”/Google Play’ or by scanning the QR code below.
App’s Name: Dynalog Casper App’s
QR Codes:
|
---|---
https://qrs.ly/tsdtxcg| https://qrs.ly/rrdtxcn
Name of the Drone’s WiFi:
DR-DF100B-B or DR-DF100B-W
Note: Google Play™ is a trademark of Google Inc., and App Store™ is a
trademark of Apple Inc.
2. Link the App with the Drone
Step 1: Press and hold the ON/OFF button till the drone’s LEDs start
flashing to turn on the drone. Then place the drone on a flat surface with the
head forward.
Step 2: Go to the Wifi settings of your mobile device and connect to the
drone’s Wifi(please refer to the”Name of Drone’s WWI” mentioned above). Tip:
The drone’s Wifi has no Internet access. To prevent your mobile device from
automatically switching to cellular data, it’s recommended that you turn off
cellular data when connecting to the drone’s Wifi.
Step 3: Open Dynalog CasperApp and tap Start to enter the App. Tap ****to
turn on the App, and the LEDs on the drone turn to solid on at a successful
connection.
Step 4: Tap to calibrate the drone.
Notes:
- If the drone’s Wifi is not listed or the App doesn’t show the preview image, please restart the drone and search the Wifi of the drone again.
- Make sure the drone’s Wifi is only connected to one device.
- Please allow the App Dynalog Casper to access the necessary permissions of your mobile device.
- Tapp to check the recorded videos and captures photos.
3. Function Overview of the App
1. Back
2. VR Mode
3. Trajectory Flight
4. Calibrate
5. Virtual Remote ON/OFF
6. Drone Battery Status
7. Wifi Signal| 8. Trim clockwise/anticlockwise
9. Emergency Stop
10. Trim leftward/rightward
11. Trim forward/backward
12. Turn Left/Turn Right/ Ascend/Descend
13.Forward/Backward/ Leftward/Rightward
---|---
A Speed Switch
B 360° Flip
C Headless Mode
D One Key Take-off/Landing| E Gestures for Photo/Video
F Photo
G Video
H Voice Control
---|---
VR Mode:
VR device (not included) is required to activate VR Mode.
Trajectory Flight:
Tap to activate this mode. Draw a path in the frame on the right side of the
screen and the drone will fly following the path. Tap to modify flight
distance and time accordingly. Tap again to exit this mode.
Calibrate:
Tap to calibrate the drone directly.
If the LEDs of the drone flash quickly after a sudden impact, please tap to
calibrate the drone.
Battery Status:
Check the battery status of the drone.
Wifi Signal:
Check the Wifi status of the drone to avoid losing control. When it drops to 2
or 1 bar, please do not fly the drone far away.
Gestures for Photo/Video:
Tap to activate this function. Stand in front of the camera at a distance of
1.5-3 meters, face the camera and make a gesture with your right hand to take
a photo, a gesture to start or stop recording a video.
Photo:
Tap once to take a photo. Please allow Dynalog Casper to access the photos on
your phone before taking a photo.
Video:
Tap once to start recording, tap again to end and save the video. The interval
time between recording and saving a video should be over 3 seconds.
Voice Control:
Press and hold CI to speak the following voice commands: Take off, landing,
forward, backward, left, right. Please allow Dynalog Casper to access the
microphone on your phone before speaking the voice command.
STOP
Stop: Tap STOP and a pop-up window will show to confirm if you would like
to stop the drone.
Note: It’s NOT recommended to use this function during normal flight for
landing, which may result in serious damage for your drone.
Camera Views:
: View from the drone’s camera
: View from your mobile device’s rear camera
:View from your mobile device’s front camera
Note: To fly the drone with the remote and see the image through your
mobile device in the App operation mode, tap ****to OFF, then restart the
remote and wait for the automatic pairing.
TROUBLESHOOTING GUIDE
Ql. How to avoid losing my drone?
- Make sure the distance between the drone and the remote/App is effective. We recommend flying the drone on windless days. If you insist on flying the drone in the wind, we recommend flying at HIGH speed.
- It’s essential to calibrate the drone before flying.
Q2. Drone LEDs do not light up.
- Ensure that you’ve turned on the drone.
- Replace or charge the drone battery.
- Make sure that you did not press the button on the remote to trun off the drone’s LED indicators.
Q3. Drone LEDs keep flashing, but the drone never responds to any command from the remote.
- Restart the drone and remote.
- Replace or charge the drone battery.
- Make sure the batteries of the remote have enough power.
Q4. The flight is not stable.
- Return the drone and restart to do a flight calibration as instructed.
- Make the flight trimming accordingly.
- Fly the drone when the weather is good.
Q5. The response from the drone to the control is not sensitive.
- Make sure the distance between the drone and the remote is effective.
- The remote signal may be interfered, please land the drone and go to another place to fly it.
Q6. Connection between the drone and the App is frequently lost.
- Make sure the distance between the drone and the mobile device is effective.
- Make sure your mobile device is not connected to another network.
Q7. The App doesn’t respond to voice commands.
- Ensure the drone App has access to the microphone function of your mobile device.
Q8. Some of the functions don’t work in the App.
- Make sure the switch for the App GO is ON.
Q9. The drone will fly beyond the control range.
- Activate the Headless Mode, then move the Right Control Stick to fly the drone back.
SPECIFICATIONS
USB Cable
Input| 5V 2A
Output| 5V 0.5A
Rated Power| 2.5W
FCC Caution:
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the users authority to operate the equipment. This
device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference,
and (2) this device must accept any interference received, including
interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
For Remote:
This equipment complieswith FCC radiation exposure limits set forth for an
uncontrolled environment. For R/C QUADCOPTER This equipment complieswith FCC
radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 20cm
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>