ENERLITES 961501-C-USB Brass Pop-up Floor Box with TRWR and USB Outlets Instruction Manual

ENERLITES 961501-C-USB Brass Pop-up Floor Box with TRWR and USB Outlets

Product Information

Specifications

• Product Name: 961501-C-USB and 961501-S-USB One Gang Pop-up Floor Box Assembly with 20A Duplex Tamper Resistant and USB Charger
• Features: One gang pop-up floor box with a tamper-resistant 20 amp duplex receptacle with a USB charger
• Wire Recommendation: 10-12 AWG Stranded or Solid Copper wire

Product Usage Instructions

Installation

WARNING: Turn the POWER OFF at the circuit breaker before installing the Floor Box.

Read and understand these instructions before installing. This device is intended for installation by the National Electric Code and local regulations. It is recommended that a qualified electrician perform this installation. Make sure to turn off the circuit breaker or fuse(s) and make sure the power is off before wiring the device. Use copper wire only, or equivalent.

Before Installation: Ensure there is sufficient depth & space below the subfloor.

1. Step 1: For carpeted floors: Cut out a section of carpet smaller than the size of the cover.
2. Step 2: Route 3/8(9mm) Deep For Outer Tabs.

Wiring Directions

1. Insert the HOT wire to the LINE terminal and tighten the screw.
2. Insert the NEUTRAL wire to the NEUTRAL terminal and tighten the screw.
3. Insert the GROUND wire to the GREEN terminal and tighten the screw.

Warranty Information
For warranty information, please refer to the warranty documentation provided with the product.

FAQ

• Q: Can this floor box be used in outdoor installations?
  A: This floor box is designed for indoor use only.

• Q: What is the maximum load capacity of the USB charger?
  A: The USB charger has a maximum load capacity of 20 amps.

SPECIFICATIONS

Cover Material

• 961501 ……………………………………………………………………………Brass(C) or Nickel-Plated Brass(S)
• Receptacle Rating …………………………………………………………………………………………..20A 125VAC
• USB Ports ……………………………………………………………………………………………………2.1 Amp @ 5V
• Box Material ……………………………………………………………………………………………..Galvanized Steel
• Knockout size …………………………………………………………………………………………………1/2″ and 3/4″
• Adjustable Height ………………………………………………………………………………………….up to 1″ depth

DESCRIPTION/ FEATURES

Included is a One Gang pop-up floor box with a tamper-resistant 20 amp duplex receptacle with a USB charger.

• Compact and stylish design with adjustable height function metal box with the choice of Brass(C) or Nickel-Plated Brass(S).
• Corrosion-resistant hardware ensures a long life span and reliable performance. Easy access to power when you need it. Snap the cover closed when not in use.
• Used for carpet and wood floors. Also great for countertop applications.

WARNING Turn the POWER OFF at the circuit breaker before installing the Floor Box.

Read and understand these instructions before installing. This device is intended for installation by the National Electric Code and local regulations. It is recommended that a qualified electrician perform this installation. Make sure to turn off the circuit breaker or fuse(s) and make sure the power is off before wiring the device. Use copper wire only, or equivalent.
NOTES: 10-12 AWG Stranded or Solid Copper wire is recommended.

FLOOR BOX INSTALLATION

Before Installation:
Ensure there is sufficient depth & space below the subfloor.

Step 1
For carpeted floors: Cut out a section of carpet smaller than the size of the cover.

For wood sub-floors and finished hardwood floors:

• Tape the template on the area you want to place the floor box.
• Use a knife to cut the outline of the box. Start with the ears and move inwards.
• Following the outline, cut the box shape without the ears completely through the subfloor or hardwood floor.
• Following the outline, cut 3/8″ deep into the subfloor or hardwood for the mounting ears.
  • Using a router is recommended

Step 2

• Remove knockouts and secure the box onto the floor. Pull the wires through the opening of the floor and the knockout and connect the wires based on the wiring diagram.
• Use the proper connector/ clamp at the knockouts to secure the wires and to avoid accidental wire stripping.
• Secure the box to the opening using wood screws.

WIRING DIRECTIONS

1. Insert the HOT wire to the LINE terminal and tighten the screw.
2. Insert the NEUTRAL wire to the NEUTRAL terminal and tighten the screw.
3. Insert the GROUND wire to the GREEN terminal and tighten the screw.

WARRANTY INFORMATION

This device is warranted to be free of material and workmanship defects for 2 years from the date of purchase. Original receipt or proof of purchase from an authorized retailer must be presented upon warranty claim. ALL claims must be verified and approved by Enerlites, Inc. Warranties from other Enerlites products may vary. This warranty is nontransferable and does not cover normal wear and tear or any malfunction, failure, or defect resulting from misuse, abuse, neglect, alteration, modification, or improper installation. To the fullest extent permitted by the applicable state law, Enerlites shall not be liable to the purchaser or end user customer of Enerlites products for direct, indirect, incidental, or consequential damages even if Enerlites has been advised of the possibility of such damages. Enerlites’ total liability under this or any other warranty, express or implied, is limited to repair, replacement or refund. Repair, replacement or refund are the sole and exclusive remedies for breach of warranty or any other legal theory.

© 2019 Enerlites Inc. CA, U.S.A.
WWW.ENERLITES.COM
0202190134-02
REV 20230802

References

• Manufacturing Lighting Controls & Wiring Devices - Enerlites

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>