maytronics Dolphin Trident Pro Robotic Pool Cleaners User Guide

: June 6, 2024
: maytronics

Table of Contents

Cautions & Warnings
Helpful Hints
Robot Operation
Remote Control
Digital power supply
Caddy Assembly
Read User Manual Online (PDF format)
Download This Manual (PDF format)

**maytronics Dolphin Trident Pro Robotic Pool Cleaners User Guide

**

Dolphin TRIDENT PRO

Thank you for purchasing a Maytronics Robotic Pool Cleaner. The Robotic Pool Cleaners by Maytronics deliver advanced cleaning technologys, long lasting performance and easy maintenance. You and your family will be free to enjoy swimming with full confidence that your pool is completely clean.

Cautions & Warnings

Use the originally supplied power supply only.
Do not use an extension cable in any case whatsoever.
Ensure the electrical outlet is protected by a ground fault interrupter (GFI) or an earth leakage interrupter.
Keep the power supply out of standing water.
Do not enter the pool while the Pool Cleaner is working.
Unplug the power supply before servicing.
Do not pull the Pool cleaner from the pool using the cable.
Use the Pool Cleaner in the following water conditions only: Chlorine Max 4 ppm; pH 7.0 – 7.8; Temperature 6 -34°C (43-93°F); NaCI Maximum = 5000 ppm.
Specifications: Motor protection: IP 68 Minimum depth: 0.80m/2.6ft Maximum depth: 5m/16.4ft

Helpful Hints

When working, the Power Supply should be placed in the shade.
If the Dolphin is fitted with combined or wonder brushes, gently aqueeze the brushes until they are soaked with water.
Release minimal required floating cable length to ensure proper pool coverage. Leave excess cable rolled outside the pool.
After each cleaning cycle wash the filter bag or cartridge. Clogged filter bags reduce scanning and cleaning efficiency.
Once a week unplug the cable from the power supply, unwind the tangled portions of the cable, straighten it out and leave it in the sun for several hours.
Store the pool cleaner in a shady place on its Caddy, if not on a caddy, place the pool cleaner upside down.

For a detailed Manual (including videos): manuals.maytronics.com/9991083-TRIPRO

Robot Operation

Set up
Position the power supply at least 3mJ /10ft away from the edge of the pool.

Change the handle position to diagonal. This will determine the speed at which the robot advances along the waterline.
Into the pool
Operation

The robot will now begin working for a complete cleaning cycle. At the end of the cycle, it will automatically switch itself off.

Out of the pool
Cleaning the filter
Periodical maintenance
Unplug the supply before servicing
Storage
Coil the cable and store in a cool, dry place on the Caddy. Do NOT store the robot where it will be exposed to direct sunlight, excessive heat or to frost.

Remote Control

Menu Screen

Menu Screen Menu
Screen

Digital power supply

Input – 100-250 AC Volts
50-60 Hertz
180 Watt
Output – <30 VDC
IP 54

Digital power supply

Full filter indicator

The power supply is equipped with a unique filter status indicator. The red LED indicates 2 filter conditions:

When blinking – The filter is partially blocked
When lighted – The filter is blocked and must be emptied and cleaned

If the LED does not shut-off after the filter has been emptied and cleaned, press the RESET button while the robot is working.
Digital power supply

Weekly Timer

When the power supply is switched on, the 3 LEDs will blink for 5 seconds. At this time by pressing the SELECT button you may choose a pool cleaning schedule for the coming week.

Note! – The robot will always begin to work upon set-up.

LED 1 – The robot will automatically work every day for a full cycle = 7 times a week.
LED 2 – The robot will automatically work every other day for a full cycle – 3 times a week.
LED 3 – The robot will automatically work every 3 days = 2 times a week.

If you do not press any of the buttons in the first S seconds after the power supply has been switched on the robot will work for one cycle only.

While the robot is working in weekly timer mode the LED will blink constantly between cycles. At the end of the week the power supply automatically switches off. You must reschedule the robot.

For a detailed Manual (including videos): manuals.maytronics.com/9991083-TRIPRO