cablematic S2B5232R Wireless Bluetooth Adapter

Package content:

BLE Beacon RS-232 Reader

White Box Dimension : 11 x 6 x 5 (cm)
Total Package Weight : 105 g

• BLE RS-232 reader x 1
• A4 User manual x 1
• Mini USB Cable x 1
• BLE RS-232 reader x 1
• A4 User manual x 1
• Mini USB Cable x 1

Profile:

Top view:

LED       Description
Blue         Flash when data received
Red          Solid when power on

DB9 connector: (Male)

Pin| Signal| DTE Direction| DCE Direction| Description
---|---|---|---|---
1| N/A|  |  |
2| RxD| Output| Input| Transmitted data
3| TxD| Input| Output| Received data
4| N/A|  |  |
5| GND|  |  | Ground
6| N/A|  |  |
7| RTS|  |  |
8| CTS|  |  |
9| Vin|  |  | Power Input (5~27 VDC)

Rear Side:

Default : All pin is “0”, Baud rate 9,600 bps., 8 Data bits, None parity, 1 Stop bit. Baud rate option : DIP No. 8 is set to “1” (On): The baud rate is 115,200 bps, 8 Data bits, None parity, 1 Stop bit.

Packet Format:
Default : All DIP switch is “0”. The reader will filter “Uconnect™”, “iBeacon™”,

$,,,<tag id>,,,,,#

Field	Description
$	start of report
msg type	Type of message ex. 0: reserved, 1: Uconnect™ tag

2: iBeacon™, 3: Eddystone™, 4: Altbeacon™

reader id| 6 bytes ID of reader in hex => 12 chars
tag type ()| type of tag ex. 1: tag w/o g-sensor, 2: tag w/ g-sensor ..
tag id| 6 bytes ID of tag in hex => 12 chars
tag batt ()()| batt voltage of tag in 1/10 volt unit
tag button status ()| button status ex. 0: released, 1: pushed
tag motion status ()| motion status ex. 0: non-moving, 1: moving
Sensor ()()| Various sensor data (11 bytes)
tag rssi| tag read rssi

| end of report

Remark

1. (*): The message is “0” for iBeacon™, Eddystone™ and Altbeacon™ beacon.

2. (**): Eddystone™-TLM version 0 include the Tag battery information, 1/10V; The version is none “0” will display “0” in the “Tag batt” column.

3. (*): Tx Power for the iBeacon™, altBeacon™, Eddystone™-UID, Eddystone™-URL and Eddystone™-EID beacon
   Example:**

   • $1,00A05053849D,1,00A050172A2C,30,0,0,,-71#
   • $2,00A05053849D,0,58E72F0CEF88,0,0,0,0,-48#
   • $3,00A05053849D,0,772BB24ADC36,0,0,0,0,-48#
   • $4,00A05053849D,0,012AC345EB45,0,0,0,0,-49#

Raw BLE packet: The Bluetooth discovering broadcast will be filtered. All BLE beacon will be reported. DIP No. 1 is set to “1” (On) and “0” else

• Prefix: “$”
• First column: RSSI value
• Mac. ID: “00A05053849D”
• Raw packet data is between “$” and “CR” ”LF”
• Suffix: CR LF

EX:
$-78,00A05053849D,0201061BFF5900AABC0100A050172A2C1E00000000000000000000000000BB
$-83,00A05053849D,1EFF06000109200073C68487B4DFB227B7546E97078954811C4EB1E40DC1DF

Add the “>” at the end of Raw BLE packet: DIP No. 2 is set to “1” (On) and “0” else.

Prefix: “$”
First column: RSSI value
Raw packet data is between “$” and “>”
Suffix: “>

EX: $-85,02010605166E2A850A04160F18090F09425055434B205420383030423635> 3.4 Add the “>” and “CR” “LF”at the end of Raw BLE packet: DIP No. 2 is set to “1” (On) and “0” else Prefix: “$”
First column: RSSI value
Raw packet data is between “$” and “>”
Suffix: “>” “CR” “LF

Raw iBeacon® packet only: DIP No. 1 & 2 is set to “1” (On) and “0” else

Prefix: “$”
First column: RSSI value
Mac. ID: “00A05053849D”
Raw packet data is between “$” and “CR” ”LF”
Suffix: “CR” ”LF”
EX: $-85,00A05053849D,02010605166E2A850A04160F18090F09425055434B205420383030423635

Raw Eddystone™ packet only: DIP No. 1 & 2 is set to “1” (On) and “0” else

TPMS packet: DIP No. 3 is set to “1” (On) and “0” else Raw data, EX: 66F35AC800
GPS Tracker & TPMS: DIP No. 1 & 3 is set to “1” (On) and “0” else, Add “AT$SNDTXT=” with TPMS packet as the section 3.6

EX : AT$SNDTXT=66F35AC800

GPS Tracker & iBeacon™ tag In/Out: DIP No. 2 & 3 is set to “1” (On) and “0” else.

When a new iBeacon™ is detected, flag=1, major, minor, power and RSSI

EX: 1;23A01AF0232A45189C0E323FB773F5EF00010002C523
1 = new beacon

UUID = 23A01AF0232A45189C0E323FB773F5EF
major = 0001
minor = 0002
measured power = C5
RSSI = 0x23

When the iBeacon™ left the device (life time ~30sec.), flag=0

EX: 0;23A01AF0232A45189C0E323FB773F5EF00010002
0 = lost beacon
UUID = 23A01AF0232A45189C0E323FB773F5EF
major = 0001
minor = 0002

Output format: 0x02 [data from §3.8.1 & §3.8.2] 0x0D 0x0A 0x03
EX : 0x02 1;23A01AF0232A45189C0E323FB773F5EF00010002C523 CR LF 0x03

TPMS APP for ID setting: DIP No. 6 is set to “1” (On) and “0” else

TPMS APP for ID setting: DIP No. 1 & 6 is set to “1” (On) and “0” else, Add “AT$SNDTXT=” with TPMS packet as the section 3.10

Power supply:

• Voltage: 5~40 VDC, Don’t exceed the limit.
• There’re 3 ways to power the adapter: Mini USB, Terminal Block and pin9 of DB9, please choose one. Don’t power the adapter by more than one source.
• The mini USB cable is inside the standard package.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>