cablematic AN133 Wi-Fi Smoke Detector Instruction Manual
- June 6, 2024
- CABLEMATIC
Table of Contents
Wi-Fi Smoke Detector
Introduction:
This product is a smart photoelectric smoke sensor, with an ultra-low-power MCU design. It is an early warning device, that can’t detect gas, heat, or fire, nor stop a fire or put out the fire. It is capable of real-time detecting the presence of smoke. Once detect the danger of fire smoke, a red LED will be ON and alarms to alert you and your family timely. It can be widely used in households, lounges, coffee houses, dancing halls, and any other places that need fire alarm monitoring.
Specifications
Input Voltage: DC3V LRO3
Static Current: :≤15uA
Alarm Current: :≤5160mA
Low-voltage notification:≤ 2.4v
Alarm Sound Level: 80db/1m
MR: 802.11 b/g/n
Detecting Range: 20m.
Installation Method: Ceiling Mounted
Working Temperature: -101°C-.+50°C
Working Humidity: ≤5 95%RH
Flat Ceiling Mounting
The preferred location to install a smoke sensor is in the center of the
ceiling because smoke, heat, and combustible products rise to ceil and will
laterally spread. Keep at least 30cm distance from lights or decorations, and
at least 15cm away from walls and corners.
Sloping Ceiling Mounting
If the Ceiling is sloping, please install the smoke sensor at a horizontal
distance of 90cm away from the ceiling top.
How to use:
-
Clockwise rotation of the mounting bracket, take out, and prepare to install the battery.
-
Input 2pcs AAA battery inside, the LED indicator ON, and then OFF.
-
Download the “TuyaSmart” App, or Scan below QR code to download.
https://smartapp.tuya.com/tuyasmart -
Register a Tuya Smart App account with your mobile phone, and log in. Click “+” at “My Home” or the Mid-blank space to add a device, choose Security Sensor, find Sensor (WiFi), and click.
-
Press the RESET for more than 5 Seconds with the PIN, the LED indicator flashes quickly, start network configuration automatically. Input the WiFi code to start connecting.
-
Press RESET for 5 seconds with PIN when configuration network, indicator flashes slowly, start manual network configuration mode. Input WiFi account and code to add a device.
-
Configuration network successfully, click smoke detector, long-press TEST, the buzzer will have DI DI sound, App receive the notification ” Detecting smoke”; Release TEST, App will show “No Smoke Detected”
-
Mute function
Please make sure there is no real danger of fire when using the mute function. Under known and non-fire alarm conditions, please do not block or by any other form to prohibit alarming. Press the Test/Mute button to lower sensitivity and relieve the alarm.
Test: To burn cotton produces smoke and face the smoke detector. When the smoke detector has a DiDi alarm, press TEST/MUTE to stop alarming. Please do not use a flame to do the test. -
State and Trouble Shooting
State| LED| Sound Alarm
---|---|---
Normal| Red LED flashes every 60 seconds| No
Test| Red LED ON| Rapid ‘Di-Di-Di’
---|---|---
Alarm| Red LED ON| Rapid ‘Di-Di-Di’
Low Power| Red LED flashes two times every 60 seconds| No
Standby| 15 seconds Test alarming. LED OFF| No
Auto Network Configuration| LED Indicator flashes every 1 second| No
Manual Network Configuration| LED Indicator flashes every 3 seconds| No -
If the smoke detector can’t work normally, please do check as follow:
1. If the battery has been used over, so please replace the battery timely.
2. Please clean the smoke detector timely.
3. If correct install the mounting bracket.
4. Smoke alarming ( TEST) has no notification, please make sure the distance
from installing place to the router is within 10 meters.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>