CaTeFo Star200 Dual-Channel Digital Wireless Microphone Instruction Manual

Audio & Video Equipment

Star200
Dual-Channel Digital Wireless Microphone

General Instruction

CaTeFo Star200 is a new generation 2.4 GHz wireless microphone system, dual- channel for capturing audio with dual subjects to your smartphones, tablets, DSLR cameras, consumer camcorders, PCs etc.

To provide a stable and hassle-free audio system,  CaTeFo developed the new “CA Technology” to offers strong signal and pick up detailed, broadcast- quality  sound accurately

The CaTeFo Star200 T1 kit includes one transmitter, T2 kit includes two transmitters, which are very small and lightweight enough to clip to shirts and clothing. The receiver has 16-level control audio adjustment and 3.5mm headphone jack to monitor real time audio.

Product introduction

Star200 Transmitter TX

1. Power key
   Long press to turn on or off the transmitter

2. LED indicator
   Pairing indicator

3. Mic input
   Connect to lavalier microphone

4. Built-in microphone
   Built-in microphone

5. Pair keys
   Short press for pairing with receiver

Star200 Receiver RX

1. Power key
   Long press to turn on or off the receiver

2. LED indicator
   Pairing indicator

3. Audio output
   Connect to camera, smartphone, audio recorder with supplied cables

4. 3.5mm monitor jack
   Real time monitor the audio with earphone

5. Pair keys
   1. Short press for pairing with transmitter
   2. Volume control

Operation Guide

1. Long press power button to turn on the transmitter and receiver.
2. Choose the built-in microphone or clip the supplied lavalier microphone to transmitter as audio input. “How to pair”.
3. The receiver and transmitter are paired from factory, if not, please pair the TX and RX manually referring Page 5
4. Connect the receiver to your camera, audio recorder or mixer with supplied 3.5mm TRS audio cable, or connect the receiver to your smartphone or tablet with the supplied 3.5mm TRRS audio cable
5. Ready to record.

How to pair

1. Short press transmitter “+” “-” key at the same time, the indicator flight every second
2. Short press receiver “+” “-” key at the same time, the indicator flash every second.
3. The transmitter and receiver will pair automatically.
4. The LED indicator will light on, if not, please repeat step 1 and 2.

Specifications

Ouput: 3.7V, 100MA,
Hardware Version| Transmitter board: TI-DM24-TX V1.2
Receiver board: TI-DM24-RX V1.2
Software Version| 0000FFFF-Unknown manufacturer
crystal oscillator.| 48.00MHz
module chip.| IC: CC8520 IC  TI Chip

Transmitter

Receiver

TRRS cable for Smartphone
Weight| 24g
Dimensions| 42x42x15mm

Packing List

Star200 T1

• 1×Star200 TX transmitter
• 1×Star200 RX receiver
• 1×Lavalier microphone
• 1×3.5 TRS to TRRS audio cable for smartphone
• 1×3.5 TRS to TRS audio cable for camera
• 2×Type C charging cables
• 1×User manual
• 1×Warranty card

Star200 T2

• 2×Star200 TX transmitters
• 1×Star200 RX receiver
• 2×Lavalier microphones
• 1×3.5 TRS to TRRS audio cable for smartphone
• 1×3.5 TRS to TRS audio cable for camera
• 3×Type C charging cables
• 1×User manual
• 1×Warranty card

FCC Caution.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna. -Increase the separation between the equipment and receiver. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. -Consult the dealer or an experienced radio/TV technician for help.

*RF warning for Portable device:
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

Shuntoo Tech Co.,Ltd
www.shuntoo.com
Email: info@shuntoo.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>