qtx QTFX-900 mkII 900W Fog Machine User Manual

QTFX-900 mkII 900W Fog Machine
User Manual

Introduction

Thank you for choosing the QTFX-900 mkII as part of your stage effects system. This machine is designed to provide generous fog output and reliable service for medium-sized venues. Please read these instructions fully to achieve the best results and avoid damage through misuse.

Unpacking

Your QTFX-900 mkII should reach you in good condition and should be supplied with IEC mains lead(s), mounting bracket, wireless controller with a remote, and wired handheld remote.
If there are any signs of damage or items missing from the packaging, contact your dealer immediately.

Warning

To prevent the risk of fire or electric shock, do not expose electrical parts to rain or moisture.
If liquids are spilled on the housing or through the vents, disconnect the mains, allow the QTFX-900 mkII to dry out, and have it checked by qualified personnel before further use.
Avoid any impact, dropping, or extreme pressure on the housing.
No user-serviceable parts inside – do not open the case.
Allow the QTFX-900 mkII to acclimatize to room temperature before operating.
Refer all servicing to qualified service personnel.

Placement

The QTFX-900 mkII has a built-in fluid tank and should be operated in an upright position.
If free-standing, ensure that the QTFX-900 mkII is positioned on a stable, non-slip surface.
If mounted at height, use the integral bracket and it is advisable to add a safety cable.

Safety

• Check for correct voltage and condition of IEC lead before connecting to a power outlet
• Check the condition of the remote lead and ensure that it is not trapped
• This unit must be earthed
• This unit uses a heating element – do not touch the nozzle area whilst in use!

Cleaning

• Use a soft dry or slightly damp to clean the casing
• Do not use strong solvents for cleaning the unit
• It is recommended to use fog machine cleaning fluid (160.670UK) periodically

Layout and connections

Setting up and operation

The QTFX-900 mkII requires fog fluid to produce the effect.
It is recommended to use one of the ranges of qtx fog fluids for best results.
A chart for recommended fog fluids is included further along in this document

• Unscrew the top cap of the tank and remove to fill with the selected fog fluid
• Replace the cap and close securely, ensuring the pipe is fed down to the bottom of the bottle so a consistent flow of fluid is supplied to the machine
• Select either wired or RF remote control and connect to the appropriate socket (4, 7)
• Connect the IEC mains plug
• Check the fog fluid level indicator at the rear and fill if necessary
• Switch the mains power on
• Heat up time is approximately 3-6 minutes. Please ensure that the remote button is not pressed during the heat-up time.
• If the fluid level is empty, the heater will shut down and the Fluid Low LED will light
• Switch off when not in use.
• Unplug from mains if not in use for long periods

Wired remote control

• When the machine is ready to operate, the light on the remote control will illuminate.
  You may now press the button for fog on demand.

• When the remote control light is off, the QTFX-900 mkII needs time to re-heat.
  Do not attempt to produce fog until the light is lit.

RF remote control

• There is a group of 4 DIP switches on the side of the RF controller to select the group Use only 1 switch at a time on any machine – more than 1 machine can be in a group
  DIP switch 1 ON (2, 3, 4 OFF)= group 1
  DIP switch 2 ON (1, 3, 4 OFF)= group 2
  DIP switch 3 ON (1, 2, 4 OFF)= group 3
  DIP switch 4 ON (1, 2, 3 OFF)= group 4
  The provided wireless fob transmitter has 4 buttons to actuate any of the groups

• Heat up time is approximately 3-6 minutes. Please ensure that the remote button is not pressed during the heat uptime

• When the machine is ready to operate, the “Ready” LED will light on the RF receiver You may now press the relevant group button for fog on demand

• When the “Heating” LED is lit, the QTFX-900 mkII needs time to re-heat. Do not attempt to produce fog until the light is lit.

Specifications

Troubleshooting
Warning: Hot components! … Switch off and allow to cool before touching the unit.

No light on the mains switch| Check mains voltage is correct and the socket is switched on
---|---
Check IEC lead is OK and connected properly
Check mains fuse and fuse in plug top
If fuse blowing repeatedly, refer to qualified service personnel
Wired remote light not lighting| Check remote is connected properly
If the light is permanently off, refer to qualified service personnel
No LEN lit on RF receiver| Check remote is connected properly
If LEN is permanently off, refer to qualified service personnel
No RF control| Check correct DIP switch setting
Check transmitter battery
The remote light is on but no fog output| Check fog fluid level (Fluid Low indicator)
If the fluid is OK and pumps working, the lines may be blocked
Check that nozzle is not blocked or obstructed
If blocked, clean with fog machine cleaner & distilled water

This product is classed as Electrical or Electronic equipment and should not be disposed of with other household or commercial waste at the end of its useful life. The goods must be disposed of according to your local council guidelines.
Errors and omissions excepted.
Copyright© 2021 AVSL Group Ltd, Unit 2 Bridgewater Park,
Taylor Road, Trafford Park, Manchester. M41 73Q.
AVSL (Europe) Ltd, Unit 3D North Point House,
North Point Bus. Park, New Mallow Road, Cork, Ireland.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>