qtx 151.608UK Tetra 4 In 1 Stage Light Effect User Manual

qtx 151.608UK Tetra 4 In 1 Stage Light Effect

Caution: Please read this manual carefully before operating Damage caused by misuse is not covered by the warranty.

Introduction

Thank you for your purchase of the QTX TETRA light effect. This model can deliver an extra wide array of colourful projections coupled with powerful UV/strobe and laser effects. Please read and keep this user manual to get the best from your purchase and avoid damage through misuse

Warning

• To prevent the risk of fire or electric shock, avoid contact with moisture or humid environments.
• No user-serviceable parts inside – Do not open the case – refer all servicing to qualified service personnel.

Please do not open cover, contains high voltage. This product is not serviceable or repairable by the end user. Please refer to qualified personnel for service and repair.

Caution: Laser radiation

Avoid pointing directly towards eyes. Laser output can cause injury if viewed directly. This product is a Class 3B laser and should only be installed and used by persons who are trained in the management of laser radiation and are able to operate in accordance within the guidance given by the Health and Safety Executive (HSE) in HS(G)95: “The Radiation Safety of Lasers used for Display purposes”. Copies of this guide can be downloaded from: www.avsl.com/assets/documents/hsg95.pdf

Safety

Check for correct mains voltage and condition of power lead before connecting to a power outlet.

Placement

• Use the included mounting bracket to fix to a stand or lighting truss
• Use secondary safety fixings if mounting overhead.
• Ensure adequate airflow around the fixture housings
• Ensure adequate access to controls and connections

Cleaning

• Use a soft cloth with a neutral detergent to clean the casing as required
• Do not use strong solvents for cleaning the unit

In the box

Please open the package carefully and check that all contents are present and in good condition. Contact your retailer if any part is missing or broken.

• TETRA LED & laser light effect
• I.R. remote control
• Mounting bracket
• Laser keys (x2)
• UK mains plug to IEC lead

Rear panel

Installation

Install the TETRA free standing on a stable surface or suspended from a lighting stand or truss. When mounting to a stand or truss, use the included adjustable fixing bracket and ensure that a safety wire is used if mounting overhead. If the TETRA is to be operated by DMX control, connect the DMX control signal to the DMX IN connector using an XLR lead and connect further DMX fixtures being controlled from the DMX OUT connector. Connect mains power to the TETRA using the supplied IEC lead or equivalent, ensuing the supply voltage is correct and capable of the load demand.

Remote control

• The TETRA is supplied with an infra-red remote control for quick operation.
• This is powered by a CR2025 button cell, which should be engaged by pulling out the plastic tab.
• Point the remote towards the front of the TETRA housing, where the I.R. receiver is located.
• The remote controls are explained in the diagram below

Onboard Menu

For more detailed setup and operation, the TETRA has an onboard control panel at the rear. Using the MENU, UP, DOWN, ENTER buttons to navigate gives in- depth control of the internal functions. The onboard control menu functions are described in the table below.

Standalone operation

As described in the menu above, the TETRA can be operated in standalone mode by setting the operation of water effect, fireball, UV and white flood/strobe LEDs. Various preset, auto and sound-activated modes can also be accessed using the I.R. remote control.

DMX operation

The TETRA light effect is compatible with standard DMX512 control. Connect a DMX controller to the TETRA using an XLR DMX lead into the DMX IN connector. Connect further DMX light fixtures that are being controlled from the DMX OUT connector to the DMX IN of each fixture in a daisy-chain. Set the DMX start address of the TETRA and all other lighting fixtures in the chain to accommodate all the required channels for each. The TETRA has 11 DMX channels and the table below is described with the DMX start address set to A001.

DMX Channels

3

| 000 – 009| Fireball off
010 – 044| Fireball Red
045 – 079| Fireball Green
080 – 114| Fireball Blue
115 – 149| Fireball Red + Green
150 – 184| Fireball Green + Blue
185 – 219| Fireball Red + Blue
220 – 255| Fireball Red + Green + Blue

4

| 000 – 009| Laser off
010 – 099| Laser Red
100 – 199| Laser Green
200 – 255| Laser Red + Green
5| 000 – 009| UV off
010 – 255| UV on
6| 000 – 007| All effects on
008 – 255| Combinations of 1, 2, 3 or 4 effects
7| 000 – 009| Strobe off
010 – 255| Strobe fast to slow
8| 000 – 009| Water wave motor off
010 – 255| Water wave motor fast to slow
9| 000 – 009| Fireball motor off
010 – 255| Fireball motor fast to slow

10

| 000 – 009| Laser motor off
010 – 127| Laser motor fast to slow clockwise
128 – 255| Laser motor slow to fast anticlockwise

11

| 000 – 050| Manual setting from DMX channels 1-10
051 – 150| Auto program 1
151 – 200| Auto program 2
201 – 250| Sound program 1
251 – 255| Sound program 2

Specifications

This product is classed as Electrical or Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life. The goods must be disposed of according to your local council guidelines

Copyright© 2021 AVSL Group Ltd, Unit 2 Bridgewater Park, Taylor Road, Trafford Park, Manchester. M41 7JQ.

AVSL (Europe) Ltd, Unit 3D North Point House, North Point Bus. Park, New Mallow Road, Cork, Ireland.

www.avsl.com

References

• AVSL
• AVSL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>