qtx Tri-PAR Rechargeable PAR Uplighter User Manual

qtx Tri-PAR Rechargeable PAR Uplighter

Tri-PAR Rechargeable PAR Uplighter

Item ref: 154.047UK User Manual

Please read through this manual thoroughly before use, any damage caused by misuse of product will not be covered by warranty.

Compact yet surprisingly powerful, the QTX Tri-PAR is perfect for many events and scenarios. Three super bright 4W LEDs provide colourful mixes and washes for walls and ceilings and the internal, rechargeable battery means the unit is totally portable and can be placed in any location without requiring a power source. Simple to operate using the onboard control panel, supplied RF remote control or DMX if preferred, the Tri-PAR is packed with features and integrated light shows that are sure to illuminate any occasion

In the box

Your Tri-PAR should arrive with you in a single carton in good condition. The carton should contain

• 1 x main unit
• 1 x remote control
• 1 x UK IEC mains lead
• 1 x user guide

Warning:

To prevent the risk of fire or electric shock, do not expose the unit to rain or damp environments. In the event of a spillage,disconnect the mains and allow the unit to dry out naturally.
Qualified personnel should then check the unit before continuing use.

Please do not open cover, contains high voltage. This product is not serviceable or repairable by the end user. Please refer to qualified personnel for service and repair.

Placement

• Ensure the unit is placed on a flat surface.
• Ensure there is at least 50cm clearance around the unit to allow for proper ventilation.
• Do not place the unit near heat sources such as radiators or heaters.
• Avoid placing the unit in direct sunlight or near strong light sources.
• Keep away from damp or dusty environments.
• Ensure adequate airflow around the fixture housings.
• Ensure adequate access to controls and connections.

Cleaning

Use a soft, dry cloth to clean the unit. Do not use any cleaning agents or solvents.

• Use a soft cloth with a neutral detergent to clean the casing as required.
• Use a vacuum cleaner to clear ventilation grilles of any dust or debris build-ups.
• Do not use strong solvents for cleaning the unit.

Front/rear panel controls

1. Battery status indicators
2. LED display
3. Manual control buttons
4. Microphone
5. DMX input
6. DMX output
7. On/off switch
8. IEC power output
9. IEC power input (fused)

Charging the battery:

The Tri-PAR can be either mains or battery-powered as it contains an internal rechargeable lithium battery. To charge the unit, simply connect to mains power using the IEC lead supplied and keep the Power Switch (7) off. When charging, the battery status light will glow red and when completely charged, it will turn green. It’s recommended to fully charge the Tri-PAR before first use and let the power run down each time before recharging to achieve optimum battery life of the unit.

Manual control menu:

• Press the MENU button to enter the settings menu.
• Press UP and DOWN buttons to navigate through various setting functions.
• Press ENTER button to save the desired setting.

Advanced parameter settings:
In A001 mode press and hold the Enter button for 3 seconds to enable/disable.
Press Menu button at any time to return to normal mode.

Remote control

The Tri-PAR is supplied with an I.R. remote control for quick access to most of the basic functions of the unit. This has a maximum range of approximately 4-5m and must be aimed towards the front of the unit. Controls and functions are listed on the diagram below:

• 1. On/off
• 2. Auto mode
• 3. Sound mode
• 4. Strobe
• 5. Speed+
• 6. Speed-
• 7. Mode+
• 8. Mode-
• 9. Dimmer+
• 10. Dimmer-
• 11. Red
• 12. Green
• 13. Blue
• 14. White
• 15. Colour jump
• 16. Colour fade
• 17. Master dimmer
• 18. Slave ID set
• 19. Sound sensitivity
• 20. Auto speed
• 21. Reset
• 22. Blackout
• 23. Full on
• 24. Full off

1. Dimmer/speed increase
2. Dimmer/speed decrease
3. Green static colour
4. Red static colour
5. No function
6. No function
7. Static colour mix 1
8. Static colour mix 2
9. Static colour mix 4
10. Static colour mix 5
11. Static colour mix 7
12. Static colour mix 8
13. Power off
14. Power on
15. Blue static colour
16. White static colour
17. DMX mode
18. Auto mode 1 (colour jump)
19. Strobe mode
20. Static colour mix 3
21. Auto mode 2 (colour fade)
22. Static colour mix 6
23. Sound mode
24. Static colour mix 9

DMX mode:

The Tri-PAR can be controlled by DMX signal, simply connect the DMX signal source to the DMX input on the unit via a balanced XLR lead. Extra fixtures can be controlled by the same DMX signal by looping through the DMX out on the unit. To enter DMX mode, select A001 from the menu and confirm the correct settings.

The Tri-PAR can be controlled by DMX signal, simply connect the DMX signal source to the DMX input on the unit via a balanced XLR lead. Extra fixtures can be controlled by the same DMX signal by looping through the DMX out on the unit. To enter DMX mode, select A001 from the menu and confirm the correct start address by using the “UP” and “DOWN” buttons and “ENTER” to confirm.
This unit has 4, 6 or 8 DMX channels as indicated in the table below:

(slow to fast）

| 1-255 red dimmer
CH3| 1-255 blue dimmer| 1-255 red dimmer| 1-255 green dimmer
CH4| 1-255 white dimmer| 1-255 green dimmer| 1-255 blue dimmer
CH5|  | 1-255 blue dimmer| 1-255 white dimmer
CH6|  | 1-255 white dimmer| 1-10 off ，11-255 strobe (slow

to fast）

CH7|  |  | 1-10 off

11-50 color mix mode (use Ch8 for variations)

51-100 color jump mode

101-150 gradual change mode 151-200 mutation pattern

201-220 Color jump sound

 |  |  | control

221-240 Color changing strobe sound control

241-255 mutation pattern voice control

---|---|---|---
CH8|  |  | 1-255 speed (slow to fast)

Specifications

Troubleshooting

No power (mains)| Check IEC lead and fuse (if fuse continually blows, refer to your dealer)
---|---
Check the unit is charged and the power switch is in the On position
No light output| Check control panel mode settings
Check DMX settings from controller (dimmer levels, blackout etc.)

Unresponsive to DMX

| Check that unit is in DMX mode and ensure DMX address remains lit to confirm receiving DMX signal
Check DMX controller is not set to black out
Check DMX controller is on correct fixture/page
Check master dimmer value
Check correct DMX address is set
Check DMX connection and leads
Overheating/cutting out| Ensure adequate ventilation and unit is not too close to a heat source

This product is classed as Electrical or Electronic equipment and should not be disposed with other household or commercial waste at the end of its useful life. The goods must be disposed of according to your local council guidelines.

Errors and omissions excepted. Copyright© 2022 AVSL Group Ltd, Unit 2 Bridgewater Park,Taylor Road, Trafford Park, Manchester. M41 7JQ.

www.avsl.com

AVSL (Europe) Ltd, Unit 3D North Point House,
Taylor Road, Trafford Park, Manchester. M41 7JQ. North Point Bus. Park, New Mallow Road, Cork, Ireland.154.047UK User Manual

References

• AVSL
• AVSL

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>