KEDOMO F02 Foldable Mini Drone User Guide
- June 6, 2024
- KEDOMO
Table of Contents
KEDOMO F02 Foldable Mini Drone
DRONE DIAGRAM
REMOTE CONTROL DIAGRAM
- Power ON/OFF
- Left Joystick
- Right Joystick
- Headless Mode
- One-key Return
- One-key Landing
- One-key Takeoff
- Fast/Slow Switch
- Right Trimming
- Left Trimming
- Backward Trimming
- Forward Trimming
- Roll
- Phone Clamps
INSTALLING BATTERIES
3×1.5V AAA batteries for the remote control (not included)
Insert the
battery into the drone (3.7V 650mAh Li-Po battery included)
RECHARGING DRONE BATTERY
First, take the battery out of the drone and connect one end of the USB
charging cable to the USB interface of the computer (or USB power adapter) and
the other end to the battery charging jack. The USB light will be on when
charging and off when fully charged, and the charging time will be about 40
minutes.
NOTE:
Only use the provided charging cable. Do not use the provided charging cable
to charge other products.
READY TO FLY
HOW TO SET THE FREQUENCY
Step1: Turn on the power of the fuselage and place the drone on a level
surface.
Step2: Turn on the power switch of the remote control.
Step3: The two LED lights at the front of the drone will flash. Push the
left joystick of the remote control to its highest point, then pull it to its
lowest point. The controller will “beep”, indicating that frequency setting is
complete. After completion, the LED light at the front of the drone will be
steadily lit.
CONNECTING YOUR MOBILE DEVICE
- Download the “WiFi_CAM” app on your mobile device from the App Store/Google Play or by scanning the QR code below.
- Power on the drone and the LED lights will flash. Go to Wifi settings on your mobile device and connect to the network (KIDOMO___xxxxxx).
USER MANUAL
Scan the QR code or visit the following website to download the detailed user
manual.
https://www.kidomo.net/manual/kidomoF02.pdf
CONTACT US
For any inquiries about KIDOMO products, please feel free to contact us. We
will respond within 24 hours.
Email: support@kidomo.net
Tel: 301-670-7335 (US) Mon-Fri 9am-5pm
(EST)
Official website: www.kidomo.net
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1)this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body
IC Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference; and
- This device must accept any interference, including interference that may cause undesired operation of the device.
The term “IC: “ before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Industry Canada technical specifications. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna transmitter. End-user must be provided with transmitter operating conditions for satisfying RF exposure compliance.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>