JENSEN JSBW-650 Wall Mountable 2.1-Channel Bluetooth Soundbar Speaker with FM Radio User Manual
- June 6, 2024
- Jensen
Table of Contents
** WALL MOUNTABLE 2.1-CHANNEL BLUETOOTH
SOUNDBAR SPEAKER WITH FM RADIO **
MODEL: JSBW-650
USER MANUAL
PLEASE READ THIS USER MANUAL COMPLETELY BEFORE OPERATING THIS UNIT AND RETAIN
THIS BOOKLET FOR FUTURE REFERENCE.
Please contact Spectra Customer Service at
1-800-777-5331 if you have any
questions about operating this product.
IMPORTANT SAFETY INSTRUCTIONS
When used in a directed manner, this unit has been designed and manufactured to ensure your personal safety. However, improper use can result in potential electrical shock or fire hazards. Please read all safety and operating instructions carefully before installation and use, and keep these instructions handy for future reference. Take special note of all warnings listed in these instructions and on the unit.
- Read these instructions All the safety and operating instructions should be read before the appliance is operated.
- Keep these instructions The safety and operating instructions should be kept for future reference.
- Heed all warnings All warnings on the appliance and in the operating instructions should be adhered to.
- Follow all instructions All operation and use instructions should be followed.
- Do not use this apparatus near water The appliance should not be used near water; for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.
- Clean only with dry cloth The appliance should be cleaned only as recommended by the manufacturer.
- Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. The appliance should be situated so that its location or position does not interfere with its proper ventilation. For example, the appliance should not be situated on a bed, sofa, rug, or similar surface that may block the ventilation openings; or placed in a built-in installation, such as a bookcase or cabinet that may impede the flow of air through the ventilation openings.
- Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
- AC adaptor is used as a disconnect device and it should remain readily operable during intended use. In order to disconnect the apparatus from the mains completely, the AC adaptor should be disconnected from the main socket outlet completely.
- Only use attachments/accessories specified by the manufacturer.
- Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. ****
- Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
- This appliance shall not be exposed to dripping or splashing water and no object filled with liquids such as vases shall be placed on the apparatus.
- Power Sources The appliance should be connected to a power supply only of the type described in the operating instructions or as marked on the appliance. Do not overload wall outlet
- The battery shall not be exposed to excessive heat such as sunshine, fire, or the like
- The danger of explosion if the battery is incorrectly replaced. Replace only with the same or equivalent type.
- Do not attempt to dismantle, open or repair this product yourself. If a fault occurs, seek advice from your local qualified service technician or contact the distributor via the telephone number at the back of this instruction manual.
- Caution marking and nameplate are located on the bottom of the product.
IMPORTANT NOTE Avoid installing the unit in locations described below:
- Places exposed to direct sunlight or close to heat radiating appliances such as electric heaters.
- Places subject to constant vibration.
- Dusty, humid, or moist places.
- Sources of electrical noise such as fluorescent lamps or motors.
- In case of malfunction due to electrostatic discharge, the apparatus has to be reset by disconnecting it from the mains supply, wait at least for 60 seconds before reconnecting the AC power cord.
COMPLIANCE WITH FCC REGULATIONS
FCC ID: OKUSB78QGC0
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) this device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Protect Your Furniture
This product is equipped with non-skid rubber ‘feet’ to prevent the product
from moving when you operate the controls. These ‘feet’ are made from non-
migrating rubber material specially formulated to avoid leaving any marks or
stains on your furniture. However certain types of oil based furniture
polishes, wood preservatives, or cleaning sprays may cause the rubber ‘feet’
to soften, and leave marks or a rubber residue on the furniture. To prevent
any damage to your furniture we strongly recommend that you purchase small
self-adhesive felt pads, available at hardware stores and home improvement
centers everywhere, and apply these pads to the bottom of the rubber ‘feet’
before you place the product on fine wooden furniture.
DEAR JENSEN® CUSTOMER
Selecting fine audio equipment such as the unit you’ve just purchased is only
the start of your musical enjoyment. Now it’s time to consider how you can
maximize the fun and excitement your equipment offers. This manufacturer and
the Electronic Industries Association’s Consumer Electronics Group want you to
get the most out of your equipment by playing it at a safe level. One that
lets the sound come through loud and clear without annoying blaring or
distortion and, most importantly, without affecting your sensitive hearing.
Sound can be deceiving. Over time your hearing “comfort level” adapts to
higher volumes of sound. So what sounds “normal” can actually be loud and
harmful to your hearing. Guard against this by setting your equipment at a
safe level BEFORE your hearing adapts.
To establish a safe level:
- Start your volume control at a low setting.
- Slowly increase the sound until you can hear it comfortably and clearly, and without distortion.
Once you have established a comfortable sound level:
Set the dial and leave it there. Taking a minute to do this now will help to
prevent hearing damage or loss in the future. After all, we want you to listen
for a lifetime.
We Want You Listening For a Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and
enjoyment. Since hearing damage from loud noise is often undetectable until it
is too late, this manufacturer and the Electronic Industries Association’s
Consumer Electronics Group recommend you avoid prolonged exposure to excessive
noise.
Customer’s Record: The serial number of this product is found on its
bottom cover. You should note the serial number of this unit in the space
provided as a permanent record of your purchase to aid in identification in
the event of theft or loss.
ACCESSORIES
1 x AC Adaptor
1 x Remote Control,
1 x Stereo Audio Connection Cable with 3.5mm stereo plugs
1 x User Manual
1 x RCA Connection Cable
1 x Speaker Base for Stand
1 x Wall Mount Template
2 x Metallic Wall Mount Brackets
4 x Anchor (For Wall Mounting)
4 x Flat Head Screws (For Wall Mounting)
1 x Round Head Screw (For Vertical Base Mounting)
INSTALLATIONS
Placing the JSBW-650 on a table Ventilation
When placing the Sound Bar on an entertainment center, bookshelf, or any type
of enclosed space, be sure to allow at least 2-3 inches of space around the
Sound Bar for ventilation. If the Sound Bar is enclosed in a tight space,
without ventilation, heat generated from the Sound Bar could create potential
overheating. Placing the JSBW-650 on the floor (vertical configuration)
Attach the base as shown below and use the supplied round head screw to secure
it to the soundbar. Be sure the assembled soundbar is placed on a level
surface. Note: The JENSEN logo on the front of the speaker can be rotated 90
degrees for vertical mounting.
Mounting the JSBW-650 on a wooden wall
It’s important to be sure there are no electric, gas or water lines located
behind the wall where you are attaching the soundbar. We recommend having this
speaker professionally installed. Use the included wall mounting accessories
and template to attach the soundbar to the wall.
- Use the supplied wall mounting template to make drill hole marks on the wall. Make sure the marks are level before drilling.
- Attach the Metallic Brackets to the wall by screwing the supplied flat head screws directly into the marks that you have made on the wall as shown above.
- Place the soundbar onto the mounting brackets. Make sure the soundbar is attached firmly to the wall.
Mounting the JSBW-650 on the wall
Use a power drill to make pilot holes for the plastic anchors
- Use the supplied wall mounting template to make drill hole marks on the wall for the anchors. Make sure the marks are level before drilling.
- Use a 1/4″ (6.35mm) bit and a power drill (Not supplied) to drill holes on the marks.
- Insert the included plastic anchors into the holes and push them in until they are flush with the wall.
- Secure the supplied Metallic Brackets to the wall by screwing the included flat head screws into the anchors and tightening until the screw head is fully inserted and flush with the metallic bracket.
- Place the soundbar onto the mounting brackets. Make sure the soundbar is attached firmly to the wall.
LOCATION OF CONTROLS MAIN UNIT
Front View
Back View
Right Hand Side View
- MODE INDICATOR LED
- FM WIRE ANTENNA
- AUX-IN 1 L/R RCA CONNECTORS
- DC IN JACK
- AUX-IN 2 JACK
- FM TUNE +
- VOLUME + BUTTON
- POWER ON/STANDBY SOURCE BUTTON
- VOLUME – BUTTON
- REMOTE INFRARED SENSOR
REMOTE CONTROL
- POWER ON/STANDBY BUTTON
- VOLUME BUTTON
- SOURCE BUTTON
- BASS BUTTON
- TREBLE BUTTON
- TUNE-/SKIP BACKWARD
- BLUETOOTH PLAY/PAUSE BUTTON, FM Mono/Stereo BUTTON
- MUTE BUTTON
- VOLUME + BUTTON
- BASS + BUTTON
- BLUETOOTH PAIR BUTTON
- TREBLE + BUTTON
- EQ BUTTON
- TUNE+/SKIP FORWARD BUTTON
GETTING STARTED
CONNECTING THE JSBW-650 TO EXTERNAL AUDIO DEVICES
You can connect the JSBW-650 audio input to the audio output of your
television or DVD Player. Please see the figure below.
NOTE:
- Make sure that the power is turned off when connecting or disconnecting the other devices. Make sure that the other devices are connected to the correct terminals.
- This unit is not magnetically shielded and may cause color distortion on the screen of some TVs or video monitors. To avoid this, you may need to move the unit further away from the TV or monitor if unnatural color shifts or image distortion occurs.
CONNECTING THE AC POWER
This unit operates using the included AC adaptor with 16V 3.5A (center-
positive ) output and is compatible with standard 120V~ 60Hz AC household
power
- Insert the DC Plug of the AC Adaptor into the DC IN jack on the back of the unit. Plug the AC Adaptor into a standard 120V~ 60Hz AC wall outlet.
- Press the Power On/Standby button on the main unit or remote control to turn on the unit. Mode LED Indicator changes color from red to relative mode.
- Press the Power On/Standby button on the remote control or press and hold the SOURCE button on the main unit to turn the unit into standby mode after you
finish listening.
REMOTE CONTROL BATTERY INSTALLATION
The remote control operates on one CR2025 battery (included). To activate the
remote control, remove the insulation tab inserted in the battery compartment.
To remove the tab, pull it in the direction of the arrow in the illustration
as shown.
When the operation of the remote control becomes intermittent or
unsatisfactory, replace the original battery with a new 3-volt lithium
battery.
Replacing the battery in the remote control:
- Press in on the side of the battery holder and pull the holder out of the remote.
- Remove the exhausted battery and then install 1 new “CR2025” lithium battery according to the polarity diagram on the battery compartment.
- Insert the battery holder into the remote control and make sure it locks into place.
NOTE: Only use a well-known brand of battery to ensure the longest life
and best performance.
Battery Precautions
- Replacement of batteries must be done by an adult.
- The supply terminals are not to be short-circuited.
- Non-rechargeable batteries are not to be recharged.
- Exhausted batteries are to be removed.
- Only batteries of the equivalent type are to be used.
- Batteries are to be inserted with the correct polarity.
- Dispose of batteries properly.
- Do not dispose of batteries in a fire.
- The batteries may explode or leak.
WARNING
DO NOT INGEST BATTERY, CHEMICAL BURN HAZARD
The remote control supplied with this product contains a coin/button cell
battery. If the coin/button cell battery is swallowed, it can cause severe
internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children. If the battery compartment
does not close securely, stop using the product and keep it away from
children.
If you think batteries might have been swallowed or placed inside any part of
the body, seek immediate medical attention.
LISTENING TO THE FM RADIO
TUNING THE FM RADIO
- Press the POWER button to turn on the unit.
- Press the SOURCE button on the remote control or tap the /SOURCE button on the main unit repeatedly selects FM radio mode, the Mode Indicator LED turns to purple color.
- To manually tune a radio station, press the TUNE + / TUNE – button on the remote control repeatedly to change stations. Use the manual tuning method to tune to weaker stations that are occasionally skipped during Automatic Tuning.
- To automatically tune to the next radio station with the strongest signal, press and hold the / button on the remote for 1-2 seconds until the purple FM indicator begins to flash. Release the button or tap the TUNE + button on the main unit. The tuner will stop scanning when it receives the next strongest station signal.
- Press the VOLUME +/- button to adjust the volume control to the desired level.
- If necessary, press the EQ to select one of the preset EQ settings or the TREBLE and BASS +/- buttons on the remote control to adjust the separate treble and bass levels.
NOTE:
- Press and hold the EQ Button for 5 seconds to reset the EQ to the default (NORMAL) setting. BASS and TREBLE settings will also be reset to the center position.
- If you press the BASS or TREBLE buttons (+ or -) while listening, the EQ will reset to the default (NORMAL) setting to allow you to increase or decrease the BASS and TREBLE as needed.
FM & FM-Stereo reception
– When listening to the FM radio, press the FM MO/ST (MONO/STEREO) button to
switch between stereo mode and mono mode. It is preferable to receive the
program in mono when you are receiving a weak station.
HINTS FOR BEST RECEPTION:
To obtain the best FM/FM Stereo reception, unwrap and fully extend the FM
Antenna and adjust the position of the wire for the best station reception
NOTE: Automatic tuning depends on the signal strength of the broadcasting
station, so weak stations may be skipped. You can manually tune to find the
weak stations if a station gets skipped. With strong signals, the tuner may
stop before it reaches the actual broadcast frequency, so you may need to
manually tune for the best reception.
BLUETOOTH OPERATION
PAIRING (LINKING) A BLUETOOTH ENABLED CELL PHONE OR OTHER BLUETOOTH ENABLED DEVICE to the JSBW-650
-
With the power on, press the SOURCE button on the remote control or tap the /SOURCE button on the main unit repeatedly to select Bluetooth mode. The Mode
Indicator LED turns blue and will be flashing. The JSBW-650 is now ready to pair (link) with your Bluetooth device. -
Turn on the Bluetooth feature of your cell phone and enable the search or scan feature to find the JSBW-650.
-
Select “JSBW-650” from the device list when it appears on your device screen. If required, enter the passcode “0000” to pair (link) the JSBW-650 with your cell phone.
-
After successfully pairing (linking) your cell phone with the JSBW-650, the Mode Indicator LED stops flashing and remains lit blue. You can now play music from your cell phone or Bluetooth device wirelessly to the JSBW-650. Note: If you want to connect the JSBW-650 to another cell phone after pairing successfully, then you need to turn off the Bluetooth on the paired cell phone first if it is in range before going through the above steps. Otherwise, the JSBW-650 will automatically reconnect to the previously linked cell phone or device.
-
Press the VOLUME +/- button to adjust the desired volume level. 6. To turn off the JSBW-650 Bluetooth, press the POWER button on the remote control or press and hold the /SOURCE button on the main unit to turn the unit to standby mode. Mode Indicator LED turns red. Don’t forget to also turn off the Bluetooth feature on your cell phone or Bluetooth device
Notes:
- Refer to the manual of your cell phone or another Bluetooth-enabled device for Bluetooth operation, since it may vary from model to model.
- If your Bluetooth-enabled device does not support A2DP, it will not play the music through the speaker, even after it’s paired (linked).
- If you are pairing (linking) your computer to the JSBW-650 using Bluetooth, you may need to set the JSBW-650 as your computer’s default sound device.
CONTROLLING THE MUSIC PLAYBACK ON YOUR BLUETOOTH DEVICE USING THE REMOTE CONTROL
- Press the POWER button to turn on the unit.
- Turn on the Bluetooth of your cell phone or device which was previously paired with the JSBW-650, press the SOURCE button on the remote control or tap /SOURCE button on the main unit repeatedly to select the Bluetooth mode, the Mode Indicator LED turns blue and begins flashing.
- After the Bluetooth device is paired with the JSBW-650, wait for around 5 seconds and then press the PLAY/PAUSE button on the remote control to start music playback from your cell phone or Bluetooth device.
- Press the PLAY/PAUSE button to pause or resume playback.
- Press the VOLUME+/- button to adjust your desired volume level
- If necessary, press the TREBLE or BASS +/- buttons on the remote control to adjust the separate treble and bass levels.
- Press the or button on the remote to select the desired music track.
- Press the POWER button on the remote control or press and hold the button on the main unit to turn off the unit after listening.
Re-linking to a cell phone or Bluetooth device
If your cell phone or Bluetooth device is already paired with the JSBW-650,
but became unlinked at some point, even with both Bluetooth devices turned on.
You can re-link them by
- Press and hold the PAIR button to re-link your cell phone. The Mode Indicator LED will turn blue and flash while linking.
- Select the JSBW-650 from the devices list on your cell phone for linking. The Mode Indicator LED stops flashing and remains lit blue if the JSBW-650 and your cell phone have been re-linked successfully.
- You can also re-link the JSBW-650 by using the Bluetooth operation of your cell phone. Please refer to the operation manual of your cell phone for more information.
PRESET EQ (REMOTE CONTROL ONLY)
The JSBW-650 features 5 different EQ modes to enhance your listening
experience. You can select the desired effect by pressing the “EQ” button on
the remote control repeatedly at the following sequence: ****
In addition, you can adjust treble and bass effects by using the TREBLE &
BASS +/- buttons.
NOTE:
- Press and hold the EQ Button for 5 seconds to reset the EQ to the default (NORMAL) setting. BASS and TREBLE settings will also be reset to the center position.
- If you press the BASS or TREBLE buttons (+ or -) while listening, the EQ will reset to the default (NORMAL) setting to allow you to increase or decrease the BASS and TREBLE as needed.
MUTE (Remote Control Only)
– Press the MUTE button on the remote control to mute the sound output from
the speaker temporarily, the Mode Indicator LED will flash.
– Press the button again to resume normal speaker playback.
LISTENING TO AUDIO FROM A TV/DVD PLAYER/VCR OR DVR
You can connect the JSBW-650 to other external audio devices using the AUX-IN
1 RCA connectors located on the back of the unit.
- Connect the external TV/DVD/VCR/DVR to AUX-IN 1 RCA connectors on the back of the unit (RCA connection cable included). Make sure the color coded plugs are attached to the corresponding color-coded connectors on the device.
- Press the POWER button to turn the unit on.
- Select external audio input by pressing the SOURCE button on the remote control or tap the /SOURCE button on the main unit repeatedly to select AUX IN 1 mode, Mode Indicator LED turns green.
- The volume level can now be controlled through the main unit. Operate all other functions on the external device as usual.
AUXILIARY INPUT
This unit provides an auxiliary audio signal input jack for connecting
external audio devices like MP3 players, CD players and listening to them
through the speakers of this unit.
- Use an audio cable (included) with one 3.5 mm stereo plug on each end of the cable.
- Plug one end into the AUX-IN 2 jack on the right-hand side (top panel) of the main unit and the other end of the cable into the Line-out Jack or Headphone Jack of your external audio device.
- Turn on the external audio device and the main unit.
- To select auxiliary audio input, press the SOURCE button on the remote control or tap /SOURCE button on the main unit repeatedly to select AUX IN 2 mode, Mode Indicator LED turns orange.
- The volume level can now be controlled through the main unit. Operate all other functions on the auxiliary device as usual.
NOTE: If you connect this unit to the Line-Out jack of your external device then you only need to adjust the volume control of this unit. If you connected the Headphone Jack of your external device then you may need to adjust both the volume control of your external device and the volume control of this unit to find the most desirable volume setting. Press the POWER button to turn off the unit when you finish listening. Don’t forget to switch off the power of your external device as well.
CARE AND MAINTENANCE
- Do not subject the unit to excessive force, shock, dust, or extreme temperature.
- Do not tamper the internal components of the unit.
- Clean your unit with a dry cloth. Solvent or detergent should never be used.
- Avoid leaving your unit in direct sunlight or in hot, humid, or dusty places.
- Keep your unit away from heating appliances and sources of electrical noise such as fluorescent lamps or motors.
CLEANING THE UNIT
- To prevent fire or shock hazards, disconnect your unit from the AC power source when cleaning.
- The finish on the unit may be cleaned with a dust cloth and cared for as other furniture, Use caution when cleaning and wiping the plastic parts.
- If the cabinet becomes dusty wipe it with a soft dry dust cloth.
- Do not use any wax or polish sprays on the cabinet.
- If the front panel becomes dirty or smudged with fingerprints it may be cleaned with a soft cloth slightly dampened with a mild soap and water solution.
- Never use abrasive cloths or polishes, as these will damage the finish of your unit.
CAUTION: Never allow any water or other liquids to get inside the unit while cleaning.
TROUBLESHOOTING GUIDE
Should you experience difficulties in the use of this player please refer to the following chart or call 1-800-777-5331 for Product Service and Support.
Symptom | Possible Problem | Solution |
---|---|---|
The unit does not respond (no power) | The unit is disconnected from the AC | |
outlet. | Reconnect to the AC outlet. | |
The AC outlet has not been powered. | Try the unit on another outlet. | |
Unit is ON but there is low or no volume | The volume control has been turned | |
all the way down. | Turn the Volume control to higher output. | |
No Sound | Bluetooth speaker is not linked with the cell phone | Go through the |
“Bluetooth Operations” process to link the speakers.
Speaker placement out of range| Relocate the speaker within Bluetooth
operating range
Noise or sound distorted on FM
broadcast| The station is not tuned properly for FM.| Full extend or rotate
the wire antenna for best reception.
Retune the FM broadcast station.
Sound is distorted| The volume level is set too high.| Decrease the volume.
| The sound source is distorted.| If the external device’s original sound
source is of poor quality, distortion and noise are easily noticed with high-
power speakers. Try a different audio source such as a music CD.
---|---|---
If you are using an external sound source like the older generation of iPods,
try reducing the output volume on the device itself. Also, try turning the
bass boost OFF or changing the EQ setting.
The unit gets warm after extended play at high volume| This is normal.| Turn
the unit off for a period of time or lower volume.
SPECIFICATION
Power requirement:
Main Unit | AC-DC Adaptor DC 16V, 3.5A |
---|---|
Remote Control | 1 X DC 3V CR2025 lithium Battery |
Frequency Range Radio Band | FM 87.5 ~ 108 MHz |
At Spectra, environmental and social responsibility is a core value of our
business. We are dedicated to the continuous implementation of responsible
initiatives with an aim to conserve and maintain the environment through
responsible recycling.
Please visit us at http://www.spectraintl.com/green.htm for more information
on Spectra’s green initiatives or to find a recycler in your area.
The Bluetooth® word mark and logos are registered trademarks owned by
Bluetooth SIG, Inc. and any use of such marks by Spectra Merchandising Intl,
Inc. is under license. Other trademarks and trade names are those of their
respective owners.
90 DAY LIMITED WARRANTY AND SERVICE
VALID IN THE U.S.A. ONLY
SPECTRA MERCHANDISING INTERNATIONAL, INC.
Warrants this unit to be free from defective materials or factory workmanship
for a period of 90 days from the date of original customer purchase and
provided the product is utilized within the U.S.A. This warranty is not
assignable or transferable. Our obligation under this warranty is the repair
or replacement of the defective unit or any part thereof, except batteries,
when it is returned to the SPECTRA Service Department, accompanied by proof of
the date of original consumer purchase, such as a duplicate copy of a sales
receipt.
You must pay all shipping charges required to ship the product to SPECTRA for
warranty service. If the product is repaired or replaced under warranty, the
return charges will be at SPECTRA’s expense. There are no other express
warranties other than those stated herein.
This warranty is valid only in accordance with the conditions set forth below:
-
The warranty applies to the SPECTRA product only while:
a. It remains in the possession of the original purchaser and proof of purchase is demonstrated.
b. It has not been subjected to accident, misuse, abuse, improper service, usage outside the descriptions and warnings covered within the user manual or non-SPECTRA-approved modifications.
c. Claims are made within the warranty period. -
This warranty does not cover damage or equipment failure caused by electrical wiring, not in compliance with electrical codes or SPECTRA user manual specifications, or failure to provide reasonable care and necessary maintenance as outlined in the user manual.
-
Warranty of all SPECTRA products applies to residential use only and is void when products are used in a nonresidential environment or installed outside the United States.
This warranty gives you specific legal rights, and you may also have other
rights which vary from state to state. TO OBTAIN SERVICE please remove all
batteries (if any) pack the unit carefully and send it to freight prepaid to
SPECTRA at the address shown below. IF THE UNIT IS RETURNED WITHIN THE
WARRANTY PERIOD shown above, please include a proof of purchase (dated cash
register receipt) so that we may establish your eligibility for warranty
service and repair of the unit without cost. Also, include a note with a
description explaining how the unit is defective. A customer service
representative may need to contact you regarding the status of your repair, so
please include your name, address, phone number, and email address to expedite
the process.
IF THE UNIT IS OUTSIDE THE WARRANTY PERIOD, please include a check for
55.00 to cover the cost of repair, handling, and return postage. All out-of-
warranty returns must be sent prepaid.
It is recommended that you contact SPECTRA first at
1-800-777-5331 or by email at
custserv@spectraintl.com for updated information on the unit requiring
service. In some cases, the model you have may be discontinued, and SPECTRA
reserves the right to offer alternative options for repair or replacement.
SPECTRA MERCHANDISING INTERNATIONAL, INC. 4230 North Normandy Avenue, Chicago,
IL 60634, USA. 1-800-777-5331
To register your product, visit the link on the website below to enter your
information. http://www.spectraintl.com/wform.htm
Printed in China (JSBW-650A)
FCC Warning
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation. Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>