GRUNDIG GDKP 5460 B Wall Mounted Cooker Hood User Manual

: June 6, 2024
: GRUNDIG

Cooker Hood
GDKP 5460 B
User Manual

Please read this user manual first!
Dear Valued Customer,
Thank you for preferring this Grundig appliance. We hope that you get the best results from your appliance which has been manufactured with high quality and state-of-the-art technology. For this reason, please read this entire user manual and all other accompanying documents carefully before using the appliance and keep it as a reference for future use. If you hand over the appliance to someone else, give the user manual as well. Follow the instructions by paying attention to all the information and warnings in the user manual.
Remember that this user manual may also apply to other models. Differences between models are explicitly described in the manual.

Meanings of the Symbols
Following symbols are used in various sections of this user manual:
Important information and useful hints about usage.
WARNING: Warnings against dangerous situations concerning the security of life and property.
WARNING: Warning for the danger of fire.
WARNING: Warning for electric shock.

This appliance has been produced in environmentally friendly facilities without harming nature.

Important safety and environmental instructions

General safety

Important Safety Instructions Read Carefully And Keep For Future Reference This section contains safety instructions that will help protect from risk of fire, electric shock, exposure to leak microwave energy, personal injury or property damage. Failure to follow these instructions shall void any warranty.

Grundig products comply with the applicable safety standards; therefore, in case of any damage on the appliance or power cable, it should be repaired or replaced by the dealer, service center or a specialist and authorized service alike to avoid any danger. Faulty or unqualified repair work may be dangerous and cause risk to the user.
This appliance is intended to be used in household and similar applications such as:
– Staff kitchen areas in shops, offices and other working environments;
– Farmhouses
– By clients in hotels and other residential type environments;
– Bed and breakfast type environments.
Operate the appliance for its intended purpose only as described in this manual.
The manufacturer cannot be held liable for damages resulting from improper installation or misuse of the product.
This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
Children shall not be allowed play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of your product must be at least 65 cm.
If the instructions for installation for the gas hob specify a greater distance, this has to be taken into account.
Make sure that your mains power supply complies with the information supplied on the rating plate of the appliance.
Never use the appliance if the power cable or the appliance itself is damaged.
Prevent damage to the power cable by not squeezing, bending, or rubbing it on sharp edges. Keep the power cable away from hot surfaces and naked flame.
Use the appliance with a grounded outlet only. WARNING: Do not connect the appliance to the mains until the installation is fully complete.
Place the appliance in a way so that the plug is always accessible.
Do not touch the lamps if they have operated for a long time. They can burn your hands since they will be hot.
Follow the regulations set out by competent authorities on the discharge of the exhaust air (this warning is not applicable for use without flue).
Operate your appliance after putting a pot, pan etc. on the hob. Otherwise, high heat may cause deformation in some parts of your product.
Turn off the hob before taking the pot, pan etc. from it.
Do not leave hot oil on the hob. Pans with hot oil may cause self-combustion.
Pay attention to your curtains and covers since oil may catch fire while cooking food such as fries.
The grease filter must be cleaned at least monthly. The carbon filter must be replaced at least every 3 months.
The product shall be cleaned in accordance with user manual. If the cleaning was not carried out in accordance with the user manual, there may be fire risk.
Do not use non-fire-resistant filtering materials instead of the current filter.
Only use the original parts or parts recommended by the manufacturer.
Do not operate the product without the filter and do not remove the filters while the product is running.
In the event of be started any flame, de-energize your product and cooking appliances.
In the event of be started any flame, cover the flame and never use water to extinguish.
Unplug the appliance before each cleaning and when the appliance is not in use.
The negative pressure in the environment should not exceed 4 Pa (4×10 bar) while the hood for electric hob and appliances running on another type of energy but electricity operate simultaneously.
In the environment where the appliance is being used, the exhaust of devices running on fuel oil or gas, such as room heater must be absolutely isolated or device must be hermetical type.
When connecting the flue, use pipes with a diameter of 120 or 150 mm. Pipe connection must be as short as possible and have as few elbows as possible.
Danger of choking! Keep all the packaging materials away from children.
CAUTION: Accessible parts may become hot when used with cooking appliances.
The product outlet must not be connected to air channels that include other smoke.
The ventilation in the room may be insufficient when the hood for the electric hob is used simultaneously with the devices operating on gas or other fuels (this may not apply to appliances that only discharge the air back into the room).
Objects placed on the product may fall. Do not place any objects on the product.
Do not flambe under your product. WARNING: Before installing the Hood, remove the protective films.
Never leave high naked flames under the hood when it is in operation
Deep fat fryers must be continuously monitored during use: overheated oil can burst into flames.

Compliance with the WEEE Directive and Disposing of the Waste Product:

This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE). This symbol indicates that this product shall not be disposed of with other household wastes at the end of its service life. Used devices must be returned to an official collection point for the recycling of electrical and electronic devices. To find these collection systems please contact to your local authorities or retailer where the product was purchased. Each household performs an important role in recovering and recycling of old appliances. Appropriate disposal of used appliances helps prevent potential negative consequences for the environment and human health.

Compliance with RoHS Directive

The product you have purchased complies with the EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive.

Package Information

Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.

General appearance

Overview

Control and parts

Inner chimney
Outer chimney
Control panel
Aluminum grease filter
Lighting

Technical data

Supply voltage & Frequency	220-240V~ 50 Hz
Lamp power	2×3 W
Motor power	210 W
Flow rate – 3. Level	645 m³/h
Insulation class of motor	Class F
Insulation class	Class I

Operation of the appliance

Controlling the appliance

Key	Function
A :1. stage button	Operates the appliance on 1st speed. When you press this

button again to turn off the appliance, the screen speed stage turns off.
B : 2. stage button| Operates the appliance on 2nd speed. When you press this button again to turn off the appliance, the screen speed stage turns off.
C : 3rd stage button| Operates the appliance on 3rd speed. When you press this button again to turn off the appliance, the screen speed stage turns off.
D : Light On/Off| You may illuminate the cooking area by pressing this button. Re-press the button to turn off the lamp.

Energy-efficient usage

When using your appliance, adjust the speed settings according to vapor and odor intensity, in order to save energy.
Use low speeds (1-2) under normal conditions, and high speed (3) for intense odor and vapor.
The lamps on the hood are placed for illuminating the cooking area.
Using them for environmental lighting shall cause unnecessary energy expenditure and insufficient lighting.

Operating the hood

Your appliance contains a motor that has various speeds.
For better performance, we recommend using low speeds under normal conditions and high speeds in cases of strong odors and intense vapour.
You can start your appliance by pressing on the desired speed setting button. (A, B, C).
You may illuminate the cooking area by pressing the lamp (D).

Automatic stop

Your appliance has an Automatic Stop feature, enabling it to ventilate for a bit more and remove the unwanted odors and vapor inside the environment and turn off automatically after the cooking is done. To enable the Automatic Stop feature, press the any speed stage button (A, B, C) on the control panel for longer than 2 seconds; the 15-minute timer function shall be activated. When the automatic stop feature is active, pressing the same speed button shall disable the automatic stop function and the appliance’s motor shall stop. This feature is disabled when you switch between different speed stages. If you want the appliance to stop automatically, you need to enable the automatic stop feature again.

Replacement of lamp

Make the electrical connections of the appliance. Your appliance uses 3W spot LED lamp. For re- placing the lamps, push downwards on the holder from its behind, turn it counter-clockwise, and take it out downwards. Apply the above operation in reverse to install new lamps (Figure 3).

Bulb|
---|---
Bulb power| 3 W
Holder/Socket| GZ 10
Bulb voltage| 220 – 240 V
Size| 53*50 mm
ILCOS code| DR/F3-220-240- GZ10-50-53
Luminous flux| 250 Im
Correlated colour temperature| 3000 K

This product contains a light source of energy efficiency class “F”.

Operation with chimney connection

Vapour is extracted through the flue duct, which is fastened to the connection head on the hood.
The diameter of the flue duct must be the same as the connection ring. In horizontal settings, the pipe has to have a slight upward slope (around 10º) so that the air can exit the room easily.

Operation without chimney connection

Air is filtered through the carbon filter and recirculated in the room. The carbon filter is used when it is impossible to use a flue in the house.
In flueless use, remove the flaps inside the flue adapter.
Remove the aluminum grease filter. To install the carbon filter, fit the filter to the tabs by centering it on the plastic piece on both sides of the fan body. tighten it by turning right or left.
Replace the aluminum grease filter.

Cleaning and maintenance

Before cleaning and maintenance, unplug the product or turn off the switch.

Cleaning of aluminum grease filter

An aluminum grease filter is used to retain the oil particles in the air. An aluminum grease filter may change color after repeated cleaning. This is normal, and you do not have to replace your filters.

Push the aluminum grease filter lock forward.
Then pull it slightly down and pull it out (Figure 4). Otherwise, you may bend the filter. Wash and rinse the aluminum grease filter with liquid detergent and replace the aluminum grease filter to their seats by carrying out the steps specified above in reverse order. These aluminum grease filter are used to retain the oil particles in the air.

You may also wash the aluminum grease filter in the washing machine.
CAUTION: In case of normal use, clean your aluminum grease filter once a month.

Replacement of carbon filters

The appliance you have purchased is appropriate for use with carbon filters.

Remove the aluminum grease filter (Figure 4).
Place the lower part of the carbon filter to the motor cabinet (Figure 5).
Press on the tab of the carbon filter and push it forward, and ensure that the tabs of the carbon filter are engaged and locked (Figure 5).
Attach the aluminum grease filter.

CAUTION:

Carbon filters shall never be washed.
Replace carbon filters once every 3 months.
You can obtain the carbon filter from the authorized services.

Installation of appliance

** WARNING: Before starting the installation, read the safety information on the user manual.
WARNING:** Failure to install with screws and stabilizers in accordance with these instructions may result in electric shock. For the installation of the hood, please contact the nearest Authorized Service. It is the customer’s responsibility to prepare the location and electrical installation of the hood.

Position of the appliance

Distance between the cooker and the cooker hood must be considered prior to assembly. This distance should be 65 cm (Figure 6).
Distance must be measured from the surface of grate for gas cookers,
From the surface of the glass for electric cookers.

Installation accessories

Product
Inner chimney
Outer chimney
Ø150/120 mm plastic flue adapter
Chimney connection plate
User manual
Assembly pattern
Hanging plates (2x)
Ø6 mm plastic dowel (2x)
Ø10 mm plastic dowel (4x)
5.5×60 wall mount screw (4x)
M5x35 hanging plate connection screw (2x)
3.9×22 chimney connection plate screw (2x)
3.5×9.5 chimney connection plate screw (2x)
M4 washer (2x)
Chimney clamp

The information required to make the location suitable for the installation of the hood is given below.

Wall mounting

Wall must be flat, straight and have sufficient bearing capacity.
Depth of drilling holes must comply with the length of bolts.
The bolts and dowels provided are suitable for brick walls. For other construction materials (e.g. drywall, plate, porous concrete), suitable fixing dowels and nuts shall be used.

CAUTION: Before drilling, ensure that there are no power, gas or water pipes in the close proximity of the drilling locations. Draw a mid location line from the ceiling perpendicular to the lower edge of the hood (Figure 7). Fix the assembly scheme on the wall. For points A and B, take the maximum dimensions of the hood as a reference, and drill points A and B you have marked with a Ø6 mm drill bit, and tap Ø6 mm plastic wall plugs. Install the chimney connection plate to the wall with 2 pieces of 3.9×22 screws (Figure 8).
To install the hood body, drill points C,D,E,F are specified in the installation template with a Ø10 mm drill bit and tap Ø10 mm plastic dowels to these points (Figure 8).
Install 2 pieces of 5.5×60 mounting screws to points C and D with a clearance of 5 mm between the screw head and the wall (Figure 8).

Install two pieces of hanging plates to the body of the hood with M5x35 mounting screws (Figure 8).

Hold the cooker hood by its body and place it on the mounting screws on the wall and tighten the screws (Figure 9).
Install M4 washers to the 5.5×60 suspension screws. Secure the cooker hood with 5.5×60 screws to the wall through the mounting hole on the interior of the appliance (Figure 9).

Connecting to chimney

If you are going to use the Ø 120/150 mm plastic Chimney adapter, connect one end of the pipe to this adapter, if you are not going to use it, to the direct output on the product. Connect the other end of the pipe to your chimney. Check that these two connections are tight enough so they will not come out when the appliance runs on full power. Check if the flaps inside the chimney operate when they are tightened with clamps. Connect the chimney connection duct outside the adapter (Figure 11/a). If the connection duct is fitted inside the adapter, suction of air shall not occur as the chimney flap that prevents the return of air will remain closed (Figure 11/b). The length of the pipe connection as well as the number of elbows must be as minimum as possible.
A: Chimney exit pipe
B: Nonreturn flaps
C: Plastic flue The valves are closed then the appliance is not operating and prevents possible outside odor and dust from entering inside.

Installation of the hood to the chimney

Make the electrical connection of your hood before starting the installation of the chimney. Slip the chimney plates around the body. Install the chimney plate to the chimney fastening plate that is secured to the wall from its upper outer edges (Figure 12).

Inner chimney
3.5×9.5 screw
Chimney connection plate

Storage

If you do not intend to use the appliance for a long time, store it carefully.
Before lifting the appliance unplug it and then let it cool completely.
Keep the appliance and its accessories in their original packages.
Store it in a cool, dry place.
Always keep the appliance out of the reach of children.

Handling and transportation

During handling and transportation, carry the appliance in its original packaging. The packaging of the appliance protects it against physical damages.
Do not place heavy loads on the appliance or the packaging. The appliance may be damaged.
Dropping the appliance will render it non-operational or cause permanent damage.

Troubleshooting

Troubleshooting	Root cause	Help
The appliance is not working.	Check your fuses.	Fuse may be blown, inspect

and restore it.
The appliance is not working.| Check the electrical connection.| Mains voltage shall be between 220 and 240 V.
The appliance is not working.| Check the electrical connection.| Check if other appliances in your kitchen operate.
The illumination light does
not operate.| Check the electrical connection.| Mains voltage shall be between 220 and 240 V.
Illumination light does
not operate.| Inspect the lamp switch.| Lamp switch shall be at “on” position.
Illumination light does
not operate.| Inspect the lamps.| The lamps of the appliance shall illuminate.
Air inlet of the appliance is inadequate.| Inspect the aluminum filter.| Under normal operating conditions, the aluminum grease filter shall be cleaned at least once in a month.
Air inlet of the appliance is inadequate.| Check the air discharge chimney.| The air discharge chimney shall be at “on” position.
Air inlet of the appliance is inadequate.| Inspect the carbon filter.| The filters of the appliances with carbon filters shall be replaced once in every 3 months under normal conditions.

Beko Grundig Deutschland GmbH
Thomas-Edison-Platz 3
63263 Neu-Isenburg
www.grundig.com