rega Neo MK2 Advance Turntable Power Supply User Guide

rega Neo MK2 Advance Turntable Power Supply

SETUP – GETTING STARTED

Switch the mains power on. Push the power button on the front panel to turn the Neo on. When the power supply is switched on, the Rega logo will illuminate RED (red indicates that 331/3 rpm is selected).

To change to 45 rpm, press the 33/45 button, this will turn the Rega logo to GREEN and will select 45 rpm. To re- select 331/3 rpm, press the button again.

IMPORTANT: When using the Neo, always position the drive belt in the 331/3 top position of the drive pulley as shown. To minimise the risk of hum being picked up by the cartridge, the Neo should be situated as far from the turntable as the cables will allow.

The Neo PSU is compatible with the following Rega models: P3-24 / RP3 / Planar 3 2016 / RP6 / P5 / P7 / RP40 Special Edition / RP8 or any older Rega turntable fitted with the aftermarket 24V motor upgrade kit.

WARNING: Only use the supplied PS1 AC adaptor.

NEVER connect a power adaptor to the turntable and another to the Neo, simultaneously.
The original power adaptor supplied with your turntable is no longer required when you connect the Neo.

WARNING: Connecting two power AC adaptors may cause serious damage.

Connect the turntable using the supplied DIN lead between the rear of the Neo and the rear of the turntable.
Make sure the PS1 AC adaptor is plugged in and connected to the 24V AC input socket on the back of the Neo.

SPEED ADJUSTMENT

Speed control adjustments are located on the rear panel of the Neo.
Speed program switch – This enables ‘set speed’ mode.
Program mode LED – This indicates the two modes of operation: Default mode (factory speed setting) and running in the speed adjusted mode.
Speed adjustment – This adjusts the speed. The step size of the speed control is 0.01 rpm.

IMPORTANT: If your drive belt is five or more years old, it’s highly recommend that it is replaced as this can cause small inconsistencies in speed which could prevent optimum adjustment when setting the Neo.

ADJUSTING THE SPEED

Note: The speed is adjusted whilst running at 331/3 rpm. Any adjustments made at 331/3 rpm will be automatically applied to 45 rpm.

1. Select 331/3 rpm.
2. Press the ‘speed program’ switch once to put the unit into ‘setup mode’ – the ‘program mode’ LED will now be permanently on.
3. Adjust the speed using the speed adjustment control. Turning clockwise will increase the speed and turning counter clockwise will decrease the speed. The step size is 0.01 rpm.
4. When the speed has been set, press the ‘speed program’ switch once to put the unit into ‘run mode’. The ‘program mode’ LED will now go out and flash approximately every 10 seconds indicating the speed has been changed from the factory setting.

TO RETURN THE UNIT TO FACTORY SETTINGS

1. Select 331/3 rpm.
2. Press and hold down the ‘speed program’ switch until the ‘program mode’ LED flashes every few seconds. Keep the button pressed until a solid LED is illuminated.
3. Whilst illuminated, press the ‘speed program’ switch button once again to fully factory reset and return to ‘run mode’.

MEASURING THE SPEED

REGA STROBE KIT (SOLD SEPARATELY)
The best way to adjust the speed of your turntable is to use the Rega Strobe kit. A stroboscopic disc is an optical instrument used to measure the speed of the
turntable by freezing the bars on the disc. The bars are illuminated by an accurate quartz locked LED pulsing at 100Hz.

MOBILE APP
Rega, along with a London mastering studio, have used the iPhone RPM app (available on the App Store) developed by Philip Broder, to check and adjust the speed of a turntable using the Neo, with positive results. We have verified the basic accuracy of the RPM app using Rega’s in-house speed measuring equipment, but as this is a third-party app we cannot guarantee the readings because of uncertainties, which could be caused by the age, condition, and operating system of the phone the app is installed on.

If you are in any doubt, you should check the calibration of the RPM app using a suitable reference.

SPECIFICATIONS

• Output to motor bi-phase
  24 V AC protected by resettable fuse.

• Power consumption
  7.2 W

• Voltage
  24 V AC

• Power supply
  Rega PS1 only

• Speed control step size
  0.01 rpm

WARNINGS
Do not unplug the power supply from the turntable whilst the unit is on. Turn off the power supply before unplugging. Do not operate the power supply without the turntable connected. A 24 V AC plus a 20 V DC signal is present on the pins of the plug. If these are shorted, it will cause damage to the power unit. Use only with the supplied Rega PS1 power supply. Never expose the unit to rain or moisture. Do not open the case covers. There are no user serviceable parts inside.

WEEE COMPLIANCE

This symbol indicates that the electronic equipment bearing it should not be disposed of as general household waste at the end of its life. The equipment should be disposed of at a collection point for waste electrical and electronic equipment in accordance with national legislation and Directive 2012/19/EU.
For more information about how to dispose of your waste electronic equipment, please contact your local authority or retailer where you purchased the product.
In the UK, please return your product to the retailer.

www.rega.co.uk
Rega Research Ltd.
6 Coopers Way
Temple Farm Industrial Estate Southend-on-Sea, Essex SS2 5TE

NEO MK2
User Manual v1
MADE IN ENGLAND
SINCE 1973

Documents / Resources

| rega Neo MK2 Advance Turntable Power Supply [pdf] User Guide
Neo MK2, Advance Turntable Power Supply, Neo MK2 Advance Turntable Power Supply
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>