SHINING 3D S3DEINSCANSE EinScan-SE Elite Desktop 3D Scanner User Guide
- June 6, 2024
- SHINING 3D
Table of Contents
SHINING 3D S3DEINSCANSE EinScan-SE Elite Desktop 3D Scanner User Guide
Preparation
Unpacking Checklist
- **Scanner Head
**
- **Turntable
**
-
Scanner Stand
-
**Scanner Bracket
**
- **Calibration Board
**
- **Calibration Board Holder
**
-
Power Cord
-
Power Adapter
-
USB Cable A
-
**USB Cable B
**
- **Quick Guide
**
- Please only use water to clean the calibration board, avoid touching any corrosive liquid.
PC Requirement
- Operating System: Win IO / 64bit
- Port: at least One USB2.0 / 3.0 port
- RAM: > El G
- Graphic Card: NVIDIA Series
- Graphic Memory: > 1 G
- CPU: i5 or higher
Scanner Assembly
-
STEP 1: Turntable Assembly
Place the turntable onto scanner stand. -
STEP 2: Scanner Head Assembly
Place the scanner head onto the bracket.
Screw the scanner into the socket on the stand.
-
Step 3: Connect the Scanner to Turntable
Plug USB cable into back of scanner, and turntable.
-
Step 4: Connect the Scanner to a Computer
Plug USB cable into back of scanner and computer USB port.
-
Step 5: Connect the Power Supply
Plug power cord into outlet and the back of scanner. -
Step 6: Turn on the Scanner
Press the touch switch for 1 second to turn the scanner on.
Software Installation
Software Download
Download software and user manual from http://www.einscan.com/software- download.
-
Step 1: Download & Service
-
Software Download
-
user Manual
-
-
Step 3: License Acquisition
During installation. you need to obtain license file online to activate your scanner. Make sure the scanner has been connected well and your computer is networking so as to detect your a computer and validate your license.
If you fail to get license online, please contact your supplier or mail your scanner serial number ( Sticker on the back of the scanner head ) toeinscan_support@shining3d.com to get the license file. Save the license file to your desktop. Click ”Local and browse the license file and“Import“.
Calibration
-
Step 1: Calibration Board Assembly
Insert calibration board onto the board holder.
-
Step 2: calibration Board Placement
Place the calibration board on the center of the turntable facing the scanner.
-
Step 3: Run the Calibration
Open software. choose your scanner model of EinScan-SE and go to NEXT.Getting started with calibration button, following the on-screen instructions to turn the calibration board in 3 directions.
Calibration Tips
You should calibrate the scanner in the initial set-up, or IF YOU MOVE THE
SCANNER OR TURNTABLE.
When you find the scanned quality is not as good as initial set-up, you can re
calibrate your scanner. Calibration is needed when alignment mistake or
failure frequently appear during the scanning.
How to Get a Successful Scan
What Can Be Scanned?
Great to Scan Under Auto Scan Mode
- Objects larger than 3O”3O”3O mm (1.2”1.2”1.2 in)
- Objects smaller than 25O25O”250 mm (3838”38 in)
- Object weighing less than 5 kg (11 lbs)
Difficult to Scan
- Transparent objects like glass
- Shining or reflective objects like varnished metal parts.
- Dark color object like black keyboard.
- Fuzzy objects like hair.
- Solution: Painting white powder on objects will improve the scan quality.
Do NOT Suggest to Scan
- Moving objects
- Hollow pattern object like Eiffel Tower souvenirs
- Objects smaller than 3O3O3O mm (1.2”1.2”1.2 in)
Note: If the size and weight of the object are out as mentioned above,
please scan on tripod without turntable by Fixed Scan Mode.
Our Scan Process
-
Step 1: Build Project
Click “New Project” button to start a new scan. -
Step 2: Texture Scan Option
Choose texture scan if color texture is needed for scanning. Or,choose non- texture scan . (Texture scan is taking little longer time, and white balance ” test should be done before texture scanning).
-
Step 3: Place Object
Make sure the object is stable during the scanning. -
Step 4: Adjust Brightness
Choose the brightness setting according to your object surface condition. Too much red appears on the object shown in the window means over bright. Note- Please check the exposure instruction in user manual.- **Bright
**
* **Dark or difficult to scan.
**
* **Bright Dark
**
* **Medium
**
-
Step 5: Scan
Click Scan button to start scanning. -
Step 6: Edit Scan
SHIFT+Left mouse: Select redundant data, the selected section will show as red. The tool bar on the top will allow you to do further edit.
Edit buttons
1. Deselect
2. Revert
3. Delete
4. Undo
5. Show/Hide Stripes
Click to save data and exit the single-piece edition.
-
Step 7: Complete the Scan in More Directions
Sometimes, if one rotate can‘t give you a full scan, you can place the object in other directions to capture the missing faces After edit, save the current scanned data. the current data will be aligned to the last scanned data automatically. -
Step 8: Manual Alignment
If automatic alignment fail during scanning, you can use manual alignment. (Misalignment doesn’t frequently happen. Please refer the detail of manual alignment in user manual). -
Step 9: Mesh
When the scan is completed. go mesh directly. Watertight or Unwatertight model can be selected due to your request.
Watertight is closed model which can be printed directly. Unwatertight model is a go mesh directly.Watertight or Unwatertight model can be selected due to your request. non-closed model keeping the missing scanned area as it is, which is usuallychosen for further design purpose in other program.
- Step 10: Save
Asc, stl,obj and ply are available.
Press the touch switch for 1 second twice to turn the scanner off.
Technical Support
Register at support.shining3d.com for support
or contact through:
Email:
einscan_support@shining3d.com
Skype: einscan_support
For more videos of the scanners, please follow our YouTube channel “ SHINING
3D” .
APAC Headquarters
SHINING 3D Tech. Co., Ltd. Hangzhou, China
P: +86-571-82999050
Email: sales@shining3d.com
No. 1398, Xiangbin Road, Wenyan, Xiaoshan,Hangzhou, Zhejiang, China,
311258
EMEA Region
SHINING 3D Technology GmbH. Stuttgart, Germany
P: +49-711-28444089
Email: sales@shining3d.com
Breitwiesenstraße 28,, 70565, Stuttgart, Germany
Americas Region
SHINING 3D Technology Inc. San Francisco, United States
P: +1415-259-4787
Email: sales@shining3d.com
1740 César Chávez St. Unit D. San Francisco, CA 94124
www.shining3d.com
www.einscan.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>