SHINING 3D AccuFab-D1s Dental 3D Printer User Guide

June 4, 2024
SHINING 3D

3D Printer AccuFab-D1s Go
Digital With SHINING 3D
SHINING 3D AccuFabD1s Dental 3D
Printer Quick Start Guide

Installation Procedure

STEP 1 Unpacking

  1. Remove steel clasps on the wooden case to open it. Cut the straps and open the inner box.

  2. Open the cover, take out the accessory box, resin tank x 2, power adaptor and power cable from fixing foam. Take out resin tanks and remove the protective films.SHINING 3D AccuFab D1s Dental 3D Printer - adaptor

  3. Take out the printer and remove the PE bag. Open the chamber door, and take out the fixed foam1 &2 .

  4. Take out build platform 3 in the fixed foam 1.

SHINING 3D AccuFab D1s Dental 3D Printer - build
STEP 2 Boot Printer
Plug in the power adaptor and connect it with the power cable. Press the power button 4 in the back, then press the power button 5 in the front.SHINING 3D
AccuFab D1s Dental 3D Printer - adaptor 1

STEP 3 Install the Printer
The build platform bracket will move up automatically after booting the printer. It is time to install the resin tank and the build platform.
Install the resin tank Remove the protective film on the protection glass. Inset the resin tank into the card slot and push it to the end in the direction indicated in the
figure. When the edges of the resin tank are inside at right angles, it means the resin tank is placed appropriately.SHINING 3D AccuFab D1s Dental 3D
Printer - resin tank

Install the build platform
Remove the protective film on the build platform. Open the handle and insert the build platform into the bracket in the direction indicated in the figure. Close the handle and lock the platform.SHINING 3D AccuFab D1s Dental 3D
Printer - handle

STEP 4 Add Material
Shake for 2 mins before pouring material into the resin tank to avoid sediment.
Note that the resin level should be between the indicator lines of minimum and maximum.SHINING 3D AccuFab D1s Dental 3D Printer -
maximum.

Note: You can also add resin during printing without pausing.

Product Preview

SHINING 3D AccuFab D1s Dental 3D Printer - Chamber Doo

Part List.

SHINING 3D AccuFab D1s Dental 3D Printer - fig

  1. Build Platform: Due to the test printing in the factory, the surface may have a few scratches, which will not affect regular use.
  2. Flash Drive: Flash drive contains Installer of AccuWare, Printer profile “*.sndev” , Activation file (.ac), User Manual, Quick Start Guide and “Factory test reports”.
  3. Angular Knife: Used to remove models from the platform after printing is finished.
  4. Putty Knife: Used to remove models from the platform after printing is finished.
  5. Scraper: Used to stir resin in the tank to avoid sediment.
  6. Brush: Used to clean extra resin on the model.
  7. Cleaning Box: Used to store parts or alcohol.
  8. Cloth: Used to clean optical path including projector lens, protection glass, and resin tank glass.
  9. PET Card: Used to level the platform and remove the cured layer

First Print

STEP 1 Installation of Software
Insert the flash drive that came with the printer into the PC, Copy the installation file to the PC. “AccuWare_3.1.X.XXX_release_install.exe” And run it. Install the software following the installation wizard. Click Finish to finish and run the software.
Note: DO NOT run the installation file from the flash drive.SHINING 3D
AccuF abD1s Dental 3D Printer - fig 1 STEP 3 Import Printer Profile
Open the AccuWare software, and click “Settings” at the top right corner. Choose “Import printer profile”and “From Local”. Locate the data file (AccuFab- D1s_XXXX-XXXXX.sndev) and click. Click “Confirm” to finish.SHINING 3D
AccuFabD1s Dental 3D Printer - software

STEP 4 Update Material Profile
Click “Settings” on the top-right. Click “system setting-update check-update” to finish the update. SHINING 3D AccuFab D1s Dental 3D Printer - chamber
4

STEP 5 Data Preparation

  1. Make sure Printer Series(AccuFab-D1s), Printer Serial No.(same as the serial number on the printer label), material and layer thickness are correct and click “Next”.
    Note: When virtual machine is selected, The sliced file can’t be used for printing

  2. Click “folder” on the left. Select the STL file for printing and click “Next”.SHINING 3D AccuFab D1s Dental 3D Printer - printing

  3. In the “Layout” scene. The model can be manipulated by position, angle, size and quantity. For more detail operations, please check for
    detailed information. After the layout procedure is done, click “Next”. SHINING 3D AccuFab D1s Dental 3D Printer - manipulated

  4. Click “Auto Support” to generate support automatically. Please check for detailed information if manually add/delete is needed. Click “Next”.SHINING 3D AccuFab D1s Dental 3D Printer - supports

  5. Click “Slice” and save the “.slp3” file to a flash drive.SHINING 3D AccuFab D1s Dental 3D Printer - adaptor7

STEP 6 Print

  1. Insert the flash drive. On FabWare’s main interface, tap “Queue”. And then tap the Flash drive button on the down-right.SHINING 3D AccuFab D1s Dental 3D Printer - button
  2. Click to choose the model to be printed in the flash drive file list.SHINING 3D AccuFab D1s Dental 3D Printer - printed
  3. Confirm printing (1.Resin 2.ResinTank 3.Light Path) ,and then click “Next”.SHINING 3D AccuFab D1s Dental 3D Printer - printing 1
  4. Close the chamber door and tap next to start printing.SHINING 3D AccuFab D1s Dental 3D Printer - chamber door

Note: If you find the software expired, please active the license according to the .

STEP 7 Post-processing
After finishing the print, take down the build platform and remove the model. Clean, dry, and cure the model. For more details about postprocessing, please check .

http://support.shining3ddental.com/en/support/solutions
Document Download Center: https://www.shining3d.com/download-center/
Support Center: https://support.shining3ddental.com/en/support/solution
Aftersales service: -Create support ticket —-Check ticket status
Technical resource: – FAQs ‘Basic Tutorials -Useful tips. -Webinars

APAC HEADQUARTERS
SHINING 3D Tech.Co.,Ltd.
P: +#86-571-82999050
No.1398 Xiangbin Road, Wenyan, Xiaoshan, Hangzhou, China, 311258| AMERICAS REGION
SHINING 3D Technology Inc.
P: +1415 259 4787 1740 César Chavez St. Unit D. San Francisco, CA 94124, United States| EMEA REGION
SHINING 3D Technology GmbH
P: +49-711 28444089
BreitwiesenstraBe 28, 70565 Stuttgart, Germany
---|---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals