INNOSILICON T2TS-26T BTC Miner Bitcoin Miner 1980W SHA-256 include PSU and Power Cord User Manual
- June 6, 2024
- INNOSILICON
Table of Contents
INNOSILICON T2TS-26T BTC Miner Bitcoin Miner 1980W SHA-256 include PSU and Power Cord User Manual
Overview
Specifications
Typical Hash rate and Power Dissipation parameters under the four Modes:（Pls refer to 3.5.1 in the manual for mode modification）
Assemble the miner
2.1 Open the package to check the miner
- Check whether the warranty sticker is damaged, especially the one on hash boards PSU port side. If the warranty sticker is damaged when you receive the miner, please contact our after-sales personnel in time.
- Before assembling the miner, pls shake the miner gently. Please contact our after-sales personnel immediately if there is metallic collision sound.
- Check if the fan works well, if you find the fans broken please contact our after-sales personnel.
- The wiring of the miner shall not be changed.
Notes:
There is an indicator on each hash board which shows the work status of the
hash board.
Being constantly lit means the hash board works properly.
Flickering represents overtemperature of the hash board. Please check the fans
of the miner, environment temperature and the ventilation conditions.
Being off means the hash board doesn’t work. Please try to reboot the miner or change the data cable. Pls contact our after-sales team if the problem still exists.
2.2 Assemble & Operate
Connect the miner and the router by the Ethernet cable and then the miner can start to run after being powered on.
Notes: T2TS-26T miners consume much more power under some modes. Pls choose proper sockets.
Normal Indicator: Being constantly lit represents static IP and
flickering represents DHCP
Fault Indicator: Being on means there is something wrong with the
network; Being off means it is OK.
IP SET button :
Press it for 1 to 4 seconds and the following functions can be realized:
- Sending the IP miner to the “Set IP” tool;
- Changing the miner to a Static IP within the specific range with the IPset tool
Press it for 4 to 15 seconds, the miner IP will be switched to DHCP and the pool settings will be restored to default settings.
Press it for 15 to 30 seconds to switch the Dynamic (Static) IP to Static (Dynamic).
RESET button: Press the “Reset” button to restart the miner.
Operate the miner
3.1 Enter the miner console
DHCP is the default IP mode of the miner (The normal indicator of the control board now is flickering in green when the DHCP service of the router is enabled.). Find the IP via the IP scanner or the SetIP tool developed by our company. Pls refer to the official support center for the downloading address https://www.innosilicon.com/html/support_en/tool.html.
a. Save SetIP in the pc on the same network with the miner, then double click the tool and choose the language.
b. Report the miner IP
Enter the IP of the miner in the browser and press the Enter button to go to
the miner console page.
Chrome is the suggested browser. (Please try with dragon admin if the password
admin is invalid.)
3.2 Configure the pool
Pls configure the pool to start mining after login.
Please use the suggested pool as below:
- f2pool：stratum+tcp://btc-65536.f2pool.com:3333
- poolin: stratum+tcp://btc-bj.ss.poolin.com:1800 or stratum+tcp://btc-sz.ss.poolin.com:1800
- ckpool：stratum+tcp://cn.ckpool.org:443 or stratum+tcp://pool.ckpool.org:3333
- btc.top：stratum+tcp://t2.btc.top:8888 or stratum+tcp://bak.t2.btc.top:3333
- slushpool：stratum+tcp://stratum.slushpool.com:3333
3.3 View the miner hash rate
After configuring the pool, the miner will mine for you. You can view the hash rate in the Miner Status screen.
3.4 Network configuration
3.5 Other pages
3.5.1 Change the operation mode
There are 4 modes available and please click the “Save” icon after your modification.
3.5.2 Overview
3.5.3 Firmware upgrade
3.5.4 Modify the login password
3.5.5 Reboot
3.5.6 Factory reset
Innosilicon After-sales Team
Email: miner_support@innosilicon.com.cn