INNOSILICON T3S-39T BTC Miner with Highest Efficiency and Stability User Manual
- June 6, 2024
- INNOSILICON
Table of Contents
INNOSILICON T3S-39T BTC Miner with Highest Efficiency and Stability
Overview
Specifications
Part Number | T3S-39T |
---|---|
Algorithm | Sha256 |
Size (L×W×H) | 422mm(L)142mm(W)201mm(H) |
Net Weight | 9.38KG |
Operating Temperature | 0–40 ℃(device junction temperature) |
Network Connection | Ethernet |
Mode | Factory |
--- | --- |
Hash rate | 39TH±5% |
Power dissipation | 2150W±10% |
Assemble the miner
Open the package to check the miner
- Check whether the warranty sticker is damaged, especially the one on hash boards PSU port side. If the warranty sticker is damaged when you receive the miner, please contact our after-sales personnel in time.
- Before assembling the miner, pls shake the miner gently. Please contact our after-sales personnel immediately if there is metallic collision sound.
- Check whether the two fans work well, if you find the fans broken please contact our after-sales personnel.
- The wiring of the miner shall not be changed.
Notes:
There is an indicator on each hash board which shows the work status of the
hash board. Being constantly lit means the hash board works properly.
Flickering represents overtemperature of the hash board. Please check the fans
of the miner, environment temperature and the ventilation conditions. Being
off means the hash board doesn’t work. Please try to reboot the miner or
change the data cable. Pls contact our after-sales team if the problem still
exists.
Assemble & Operate
Connect the miner and the router by the Ethernet cable and then the miner can
start to run after being powered on.
Notes : T3S-39T miners consume much more power under some modes. Pls
choose proper sockets.
- Normal Indicator:Being constantly lit represents static IP and flickering represents DHCP
- Fault Indicator:Being on means there is something wrong with the network; Being off means it is OK. IP SET button:
- Press it for 1 to 4 seconds and the following functions can be realized:
- Sending the IP miner to the “Set IP” tool;
- Changing the miner to a Static IP within the specific range with the IPset tool
Press it for 4 to 15 seconds, the miner IP will be switched to DHCP and the pool settings will be restored to default settings.
Operate the miner
Enter the miner console
DHCP is the default IP mode of the miner (The normal indicator of the control
board now is flickering in green when the DHCP service of the router is
enabled.). Find the IP via the IP scanner or the SetIP tool developed by our
company. Pls refer to the official support center for the downloading address:
https://[www.innosilicon.com/html/support_en/tool.html](http://www.innosilicon.com/html/support_en/tool.html).
- Save SetIP in the pc on the same network with the miner, then double click the tool and choose the language.
- Report the miner IP Enter the IP of the miner in the browser and press the Enter button to go to the miner console page. Chrome is the suggested browser. (Please try with dragonadmin if the password admin is invalid.)
Configure the pool
Pls configure the pool to start mining after login. Please use the suggested
pool as below:
- f2pool :stratum+tcp://btc-65536.f2pool.com:3333
- 2 poolin : stratum+tcp://btc-bj.ss.poolin.com:1800 or stratum+tcp://btc-sz.ss.poolin.com:1800 3 ckpool:stratum+tcp://cn.ckpool.org:443 or stratum+tcp://pool.ckpool.org:3333
- 4 btc.top :stratum+tcp://t2.btc.top:8888 or stratum+tcp://bak.t2.btc.top:3333
- 5 slushpool :stratum+tcp://stratum.slushpool.com:3333
View the miner hash rate
After configuring the pool, the miner will mine for you. You can view the hash
rate in the Miner Status screen.
Network configuration
Other pages
Change the operation mode
There are 4 modes available and please click the “Save” icon after your modification.
Overview
Firmware upgrade
Modify the login password
Reboot
Factory reset
Innosilicon After-sales Team Email: miner_support@innosilicon.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>