INNOSILICON T2THF BTC Minner User Manual

June 6, 2024
INNOSILICON

INNOSILICON T2THF BTC Minner User Manual
INNOSILICON T2THF BTC Minner

Overview

Product Overview

Assemble the miner

Open the package to check the miner
  • Check whether the warranty sticker is damaged, especially the one on hash board PSU port side. If the warranty sticker is damaged when you receive the miner, please contact our after-sales personnel in time.
  • Before assembling the miner, pls shake the miner gently. Please contact our after sales personnel immediately if there is metallic collision sound.
  • Check whether the two fans work well, if you find the fans broken please contact our after-sales personnel.
  • The wiring of the miner shall not be changed including the power cable and data cable interface as shown in the figure below.
    Assemble the miner

Notes:
There is an indicator on each hash board which shows the work status of the hash board. Being constantly lit means the hash board works properly.
Flickering represents over temperature of the hash board. Please check the fans of the miner, environment temperature and the ventilation conditions.
Being off means the hash board doesn’t work. Please try to reboot the miner or change the data cable. Pls contact our after-sales team if the problem still exists.

Assemble & Operate

Connect the miner and the router by the Ethernet cable and then the miner can start to run after being powered on.

Notes: T2THF miners consume much more power under some modes. Pls choose proper sockets.

Assemble & Operate

Normal Indicator: Being constantly lit represents static IP and flickering represents DHCP

Fault Indicator: Being on means there is something wrong with the network; Being off means it is OK.

IP SET button:
Press it for 1 to 4 seconds and the following functions can be realized:

  1. Sending the IP miner to the “Set IP” tool;
  2. Changing the miner to a Static IP within the specific range with the IP set tool:
    Press it for 4 to 15 seconds, the miner IP will be switched to DHCP and the pool settings will be restored to default settings.
    Press it for 15 to 30 seconds to switch the Dynamic (Static) IP to Static (Dynamic).

RESET button: Press the “Reset” button to restart the miner.

Operate the miner

Enter the miner console

DHCP is the default IP mode of the miner (The normal indicator of the control board now is flickering in green when the DHCP service of the router is enabled.). Find the IP via the IP scanner or the SetIP tool developed by our company. Pls refer to the official support center for the downloading address https://www.innosilicon.com/html/support_en/tool.html.

  1. Save Set IP in the PC on the same network with the miner, then double click the tool and choose the language.
    Operate the miner

  2. Report the miner IP

Enter the IP of the miner in the browser and press the Enter button to go to the miner console page. Chrome is the suggested browser. ( Please try with dragon admin if the password admin is invalid ).
Enter the miner console

Configure the pool

Pls configure the pool to start mining after login.
Please use the suggested pool as below:

  1. f2pool: stratum+tcp://btc-65536.f2pool.com:3333.
  2. poolin: stratum+tcp://btc-bj.ss.poolin.com:1800 or stratum+tcp://btc sz.ss.poolin.com:1800.
  3. ckpool:stratum+tcp://cn.ckpool.org:443 or stratum+tcp://pool.ckpool.org:3333.
  4. btc.top: stratum+tcp://t2.btc.top:8888 or stratum+tcp://bak.t2.btc.top:3333.
  5. slushpool: stratum+tcp://stratum.slushpool.com:3333.
    Configure the pool
View the miner hash rate

After configuring the pool, the miner will mine for you. You can view the hash rate in the Miner Status screen.
View the miner hash rate

Network configuration

Network configuration

Other pages

Change the operation mode

There are 4 modes available and please click the “Save” icon after your modification.

Change the operation mode

Overview

Overview

Firmware upgrade

Firmware upgrade

Modify the login password

Modify the login password

Reboot

Reboot

Factory reset

Innosilicon After-sales Team
Email: minersupport@innosilicon.com.cn

Specifications

Part Number

| T2THF
---|---

Algorithm

| Sha256
Size (L×W×H)|

266mm(L)203mm(W)278mm(H)

Net Weight

| 8.2 KG
Operating Temperature|

0–40 ℃(device junction temperature)

Network Connection|

Ethernet

Innosilicon Logo

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals